Green Energy

The Deye SUN-25K-SG01HP3-EU-AM2 is a high-performance, three-phase hybrid inverter with high-voltage battery compatibility. It has been specially developed for demanding PV applications in residential and commercial environments and impresses with its high efficiency, flexible application options, and robust construction.Highlights at a glanceHigh rated power: 25 kW for high-performance PV systems in residential and commercial environments.AC and DC coupling: Enables the retrofitting of existing solar systems and the flexible integration of battery storage.High efficiency: A maximum efficiency of 97.6% and an MPPT efficiency of over 99% ensure maximum energy yield.Scalable: Up to 10 units can be connected in parallel for on-grid and off-grid operation, enabling flexible system extension.Intelligent monitoring: Smart functions enable remote monitoring and maintenance, including remote parameter adjustment and firmware updates.Comprehensive safety: Equipped with various protective mechanisms, including overvoltage, overcurrent, and earth fault protection.Efficient energy conversion with high-voltage technologyWith a maximum DC input power of 32,500 W and an MPPT efficiency of 99.9%, the SUN-25K achieves outstanding performance. The intelligent MPPT control ensures high yields even in cases of shading or unevenly aligned module fields. The inverter is optimised for high-voltage lithium-ion batteries (160–700 V), which enables particularly high charging and discharging efficiency.Flexibility and scalabilityWhether grid-connected, hybrid, or off-grid: the inverter offers flexible application options. The AC and DC coupling enables the simple retrofitting of existing solar installations. The parallel connection of up to 10 devices, as well as two separate battery inputs, provide scalable solutions for increasing energy demands. With six freely definable time slots for charging and discharging the battery, energy can be used or stored in a targeted way. Reliability and protectionThanks to protection class IP65 and intelligent cooling, operation is ensured even under demanding conditions. Safety features such as polarity reversal, overvoltage, short-circuit and residual current protection provide maximum operational safety. Certifications according to VDE-AR-N 4105, EN 50549 and other international standards confirm the high quality of the device. Who is the Deye SUN-25K-SG01HP3-EU-AM2 suitable for? This inverter is ideal for:Commercial enterprises with high energy and storage requirementsHomeowners seeking maximum self-sufficiency with high-voltage technologyInstallers planning flexible, future-proof systemsProject developers implementing AC-coupled retrofit solutions  ModelDEYE SUN 25K-SG01 HP3-EU-AM2 Battery input data Battery typeLi-lon Battery voltage range (V)160~700 Max. charging current (A)50 Max. discharging current (A)50 Number of battery inputs1 Charging strategy for Li-Ion batterySelf-adjustment to BMS PV string input data Max. DC input power (W)32500 Rated PV input voltage (V)1000 Starting voltage (V)180 MPP voltage range (V)150-850 Full load DC voltage range (V)500-850 Rated DC input voltage (V)700 PV input current (A)26+26 Max. PV short-circuit current (A)39+39 Number of MPPT2 Strings per MPPT2+2 AC output data AC rated power and UPS power (W)25000 Max. AC output power (W)27500 AC rated output current (A)37,9 /36,3 Max. rated AC output current (A)41,7 / 39,9 Max. continuous AC pass-through (A)80 Peak power (without grid)1,5x rated power, 10 s Generator input/Intelligent load/AC coupling current (A)30,4 / 80 / 30,4 Output power factor0,8 leading to 0,8 lagging Output frequency and voltage50/60Hz; 3L/N/PE 220/380, 230/400Vac Grid typeThree-phase Total harmonic distortion (THD)< 3% ( rated power ) Direct current injection<0,5% ln Efficiency Max. efficiency97,60% Euro efficiency97.00% MPPT efficiency99,90% Protection ProtectionsAnti-islanding protection, reverse polarity protection on PV string input, insulation resistance detection, differential current monitoring unit, output overcurrent protection, output short-circuit protection, output overvoltage protection Overvoltage categoryDC Type II/AC Type III Certifications and standards Grid approvalsVDE4105 IEC61727/62116 VDE0126 AS4777.2 CEI 0 21 EN50549-1 G98 G99 C10-11 UNE217002 NBR16149/NBR16150 Safety EMC/StandardIEC/EN 61000-6-1/2/3/4, IEC/EN 62109-1, IEC/EN 62109-2 General data Operating temperature range (℃)-45~60°C, >45° C output reduction CoolingIntelligent cooling Noise (dB)<55 dB Communication with BMSRS485; CAN Weight (kg)30.5 Size (mm)408B×638H×237T（Without connectors and brackets） Degree of protectionIP65 Installation styleWall mounting Warranty10 years  FAQs about the Deye SUN-25K-SG01HP3-EU-AM2Which grid codes are stored in the inverter?The inverter contains all standard grid codes, which can be set directly in the “Setting → Grid” menu. These include VDE-AR-N 4105 for Germany, EN 50549 for the EU, and CEI 0-21 for Italy, among others. As a rule, no additional NA protection is necessary once the correct country profile has been activated.Which high-voltage storage solutions are compatible and how do I set the BMS correctly?The approved storage solutions include BYD HVS and HVM, Pylontech Force H1 and H2, Dyness Tower, and the Deye GB-L Series, among others. Each storage is assigned a specific setup number, which is selected in the menu “Battery → Lithium → Setup Number”. Alternatively, the same number can be set using the DIP switches on the battery. As manufacturers may change this at any time, it is recommended to check with a current compatibility list beforehand.How much PV power can I connect without the inverter clipping?According to the data sheet, up to 32,500 W DC input power is permitted, while the AC output power is 25 kW. This gives a DC/AC ratio of 1.3. In practice, a ratio of 1.1 to 1.2 is recommended, which corresponds to about 27.5 to 30 kWp.How loud is the inverter in operation?In standby mode, the inverter remains almost silent, as the fans only start when required. In normal operation, the noise level is below 55 decibels, as specified by the manufacturer. The device is therefore suitable for cellars and technical rooms.Can settings and firmware updates be made via the app?Yes, all settings can be controlled remotely via the Deye Cloud or the SUN-APP. This includes changes to charging and export parameters, firmware updates for the inverter, BMS and HMI, as well as possible emergency shutdown of the unit. The connection is made via Wi-Fi, LAN, or the factory hotspot network. Scope of delivery: Deye SUN-25K-SG01HP3-EU-AM2 (25 kW HV hybrid inverter) 1 x Deye SUN-25K-SG01HP3-EU-AM2 inverterAn extremely powerful three-phase high-voltage hybrid inverter with 25 kW output, integrated LCD touchscreen and three MPPT trackers for demanding photovoltaic systems.1 x wall mount bracketA reinforced metal mounting rail for safe mounting of the heavy industrial device on a load-bearing wall.1 x Wi-Fi stick (data logger)A pluggable communication module for connection to the internet for remote monitoring via Deye Cloud or Solarman App.3 x current transformers (CT - Current Transformer)External clip-on current transformers for measuring the energy flows at the house connection, necessary for zero feed-in and optimising self-consumption.1 x set of PV connectors (MC4-compatible)The necessary pairs of DC connectors (plus and minus) for connecting the PV strings to the inverter.1 x set of battery connection plugs (high voltage)Special high-voltage connectors for the safe electrical connection of a compatible HV battery storage unit.1 x communication cable (BMS)A pre-assembled RJ45 data cable for connection between the inverter and the battery management system.1 x mounting kit (screws and wall plugs)A set of stainless steel screws and heavy-duty wall plugs for the professional installation of the wall mount.1 x User ManualA printed manual with detailed installation instructions, circuit diagrams, and safety instructions.

The OLight Baton 3 Premium Edition is a complete, ultra-compact lighting system for professional users. It combines an extremely powerful miniature torch with an innovative, portable charging case. This system ensures that the torch is fully operational at all times, even on long working days without access to an external power source. It is the ideal solution for surveyors, field technicians and executives who need a reliable and always charged lighting tool.Highlights at a glancePortable charging case: Recharges the torch completely up to 3.7 times and thus enormously extends the total runtime.Compact and powerful: Up to 1,200 lumens output in a housing shorter than an index finger.Always ready for use: The torch is kept safe in the case and at the same time charged automatically.Modern charging connection: The charging case itself is quickly and easily charged via a universal USB-C port.Flexible use: Magnetic end cap and two-way clip enable hands-free working.Powerful for mobile professionalsThis system was designed for daily professional use in the field. Surveyors and inspectors can rely on their torch being fully charged even after several uses throughout the day. Service technicians have a powerful light for detailed work, which they can easily recharge in the case in the vehicle between jobs. For executives on construction sites or in production plants, the Baton 3 is a discreet yet extremely powerful light source that fits in any document or laptop bag and is always ready for use.An intelligent system for maximum autonomyThe strength of the Baton 3 Premium Edition lies in the interplay of its components. The torch itself is a small powerhouse, producing a wide, even beam for close and medium range with its TIR lens. The charging case is more than just a storage box: it is a power bank with its own 3500mAh battery. An LED indicator on the outside shows the case's charging status. Inside, the torch is charged wirelessly as soon as it is inserted, and another indicator signals the charging process.Thoughtful design for professional useEvery detail of the Baton 3 is designed for professional efficiency. The grippy texture of the aluminium housing ensures a secure grip. The two-way clip allows deep and discreet carrying in a pocket or attaching to the brim of a cap for use as a headlamp. The strong magnetic end cap allows it to be attached to metallic surfaces, turning the torch into a flexible, hands-free work light. Features  ModelOLight Baton 3 Premium Edition Product typeLED torch with charging case Max. light output (lumens)1200 Max. range (metres)166 Light intensity (candela)6889 Battery (torch)1x IMR16340 Li-Ion, 550 mAh Battery (charging case)3500 mAh Charging typeWireless charging case (USB-C) Water resistanceIPX8 (torch only) Housing materialAluminium alloy Dimensions (L x Ø, mm)63 x 21 (torch only) Weight (g)approx. 53 (torch only, incl. battery) Special featuresIncluding charging case, magnetic end cap  FAQs about the OLight Baton 3 Premium EditionWhat is the main advantage of the Premium Edition over the standard Baton 3?The crucial advantage is the supplied portable charging case. It serves not only as a robust transport box, but also recharges the torch multiple times while on the move. This makes you independent from stationary power sources throughout the working day and guarantees maximum readiness for use.Can I charge the torch without the case?Yes. The torch itself has the typical OLight magnetic end cap and can, if necessary, also be charged directly with a compatible magnetic charging cable (MCC).How do I recognise the charging status of the case and torch?The charging case has an external LED that shows its own charging status when opened or connected to a power source. Another LED inside the case lights up red while the torch is charging and green when it is fully charged. The switch on the torch itself also shows the battery status during operation.For which professional users is this system ideal?It is ideal for mobile professionals such as inspectors, surveyors, field service technicians, technical sales staff and project managers who need a compact but powerful torch they can rely on all day.How is the torch protected against accidental activation?The Baton 3 has an electronic lockout function. This is activated by holding down the side switch when the torch is switched off and reliably prevents unintentional activation in the pocket or in the charging case.

The OLight Seeker 4 Pro NW is a high-performance, rechargeable LED torch designed for demanding professional use. It combines extreme brightness with superior, true-to-life colour rendering thanks to the neutral white LED. An innovative metal rotary switch enables intuitive, infinitely variable control of brightness. With its robust construction and intelligent charging system, the Seeker 4 Pro NW is a reliable tool for security services, industry, emergency services and authorities.Highlights at a glanceExtreme brightness: Up to 4,600 lumens of illumination output for wide area and intensive lighting.Superior colour rendering: Neutral white LED (NW) for true-to-life colours and detail recognition.Intuitive operation: Stepless dimming via a robust metal rotary switch for precise light control.Robust and reliable: Housing made from a durable aluminium alloy, IPX8 waterproof.Intelligent charging system: Includes multifunctional holster charging station for stationary operation.Powerful in professional applicationsThe Seeker 4 Pro NW was developed for professional users for whom reliability and performance are crucial. For security services, turbo mode allows large areas to be illuminated, while the neutral white LED helps with identification of persons. In industrial maintenance, the true-to-life colour display makes it easier to inspect equipment and to correctly identify, for instance, colour-coded cables. rescue services and authorities benefit from the robust build, simple operation even with gloves, and the high light output for search and rescue missions.Innovative technology for professional useThe core of the Seeker 4 Pro NW is its well-considered operating concept. The side metal switch is used not only for switching on and off but, by rotating, also allows continuous and precise brightness adjustment for any situation. The supplied high-performance 21700 lithium-ion battery ensures long runtimes. The unique charging holster can be permanently mounted on a wall or in a vehicle and charges the torch automatically as soon as it is docked. This ensures it is always ready for use.Focus on safety and durabilitySafety features are essential for professional use. An integrated proximity sensor automatically reduces light output when the light is directed at a nearby object to prevent overheating or damage. An electronic lock prevents the torch from being unintentionally switched on during transport. The housing, made from a high-quality aluminium alloy, is not only IPX8 waterproof but also drop-resistant from heights of up to 1.5 metres. Features  ModelOLight Seeker 4 Pro NW Product typeProfessional LED torch Max. light output (lumens)4600 Max. lighting range (metres)260 Light colourNeutral white (4000K - 5000K) Light intensity (candela)16900 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging methodUSB-C and magnetic charging port WaterproofingIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)133 x 35 Weight (g)approx. 205 (incl. battery) Special featuresStepless brightness adjustment  FAQs about the OLight Seeker 4 Pro NWWhat is the advantage of neutral white (NW) in professional use?Neutral white light reproduces colours much more naturally than the bluish-cold light of many standard LEDs. This is crucial when inspecting technical equipment, searching for people, or assessing situations where correct colour recognition is important.For which professional groups is the Seeker 4 Pro NW particularly suitable?It is ideal for security personnel, industrial and maintenance technicians, employees of energy suppliers, police officers, emergency services and all professional users who need a robust and extremely bright torch with intuitive operation.How does the charging holster work?The supplied holster can be mounted on a wall (e.g. in a workshop or station) or in a vehicle. It has a charging connection. As soon as the torch is placed into the holster, it charges automatically and is therefore always ready for the next use.What does the built-in proximity sensor do?The sensor is a safety feature. It detects when the lamp head is very close to an object (e.g. in a pocket or accidental covering) and automatically reduces the brightness to prevent overheating or possible damage.How is the torch protected against unintentional activation?The Seeker 4 Pro NW features an electronic lock. By pressing and holding the switch when switched off, the torch is locked and cannot be accidentally activated, for example in a bag or case.

The OLight Baton 4 is the latest generation of ultra-compact high performance torches designed for everyday professional use. It combines an impressive increase in light output with innovative features in an extremely handy and pocketable format. Unique, laser-perforated indicators for brightness and battery status as well as an improved switch take user-friendliness to a new level. It is the perfect tool for all professional users who need maximum performance in the smallest possible format.Highlights at a glanceInnovative laser indicators: Laser-perforated indicators directly on the metal housing for a clear display of brightness and battery status.High performance in a mini format: Up to 1,300 lumens and 170 metres light range in an extremely compact housing.Improved ergonomics: Enlarged, easy-grip side switch for safe and intuitive operation even with gloves.Flexible use: Strong magnetic end cap and a two-way clip allow hands-free operation.Easy charging: Proven magnetic charging connection at the end of the lamp for uncomplicated charging.Powerful in professional applicationsThe Baton 4 was developed for the mobile professional for whom minimum size and maximum benefit are crucial. Inspectors, assessors and technicians appreciate it as a tool that can be carried inconspicuously in a shirt pocket and, when required, provides powerful illumination for detailed work. For security forces in civilian clothes or management staff it is a discreet but extremely powerful torch that is instantly available for patrols or unforeseen situations.Advanced technology and intuitive operationThe outstanding feature of the Baton 4 is the new status indicators. The indicators for the five brightness levels and battery status shine through precise, laser-perforated micro-holes in the aluminium housing. This enables clear and intuitive legibility without affecting the robustness of the housing. The enlarged metal switch offers improved tactile feedback for more reliable operation in all working conditions.Sophisticated design for professional useDespite its small size, the Baton 4 is a fully-fledged tool for work. The TIR lens produces a broad, soft light-beam, ideal for close-range applications. The two-way clip allows the lamp to be carried deep in the pocket or attached to the brim of a cap to act as a headlamp. The proven magnetic end cap allows it to be attached to metal surfaces, making the lamp a flexible, hands-free work light. Features  ModelOLight Baton 4 Product typeCompact LED torch Max. Light output (lumens)1300 Max. Beam distance (metres)170 Light intensity (candela)7225 Power supply1x IMR16340 Li-Ion battery, 650 mAh Charging typeMagnetic charging connector (MCC) WaterproofingIPX8 Housing materialAluminium alloy Dimensions (L x Ø, mm)63 x 21 Weight (g)approx. 52.5 (incl. battery) Special featuresLaser-engraved indicators, Magnetic end cap  FAQs about the OLight Baton 4What is the main innovation of the Baton 4 compared to the Baton 3?The main innovation is the laser-perforated indicators, which provide a clearer and more aesthetically pleasing display of brightness and battery status directly on the metal housing. In addition, the Baton 4 offers a higher maximum brightness (1,300 vs. 1,200 lumens) and an ergonomically improved switch.How do the new laser indicators work?The light from internal LEDs is directed outwards through tiny laser-generated openings in the aluminium housing. This creates a sharp and easy-to-read display without the need for separate plastic windows, ensuring durability and waterproofing of the housing.Is this torch compatible with the Baton 3 Premium Edition charging case?No, the Baton 4 is not compatible with the Baton 3 charging case. A dedicated, new version of the charging case is available for the Baton 4 (Baton 4 Premium Edition), tailored to the new dimensions and features.For which professional users is this model ideal?It is ideal for all professional users who require an extremely compact and lightweight, yet very bright torch for everyday carrying and use. This includes technicians, inspectors, project managers, and security personnel.How is the torch protected against accidental activation?The Baton 4 features an electronic lock-out function. This is activated by pressing and holding the side switch with the light switched off, reliably preventing accidental activation during transport in a bag.

The OLight X9R Marauder is a high performance professional searchlight that redefines the boundaries of mobile lighting technology. With a monumental light output of 25,000 lumens, it has been developed for the most extreme and demanding operational scenarios where massive and far-reaching illumination is essential. Intelligent thermal management, a high-capacity battery pack and intuitive operation make the X9R Marauder the ultimate lighting tool for professional emergency services, authorities and large-scale industrial operations.Highlights at a glanceMonumental light output: Extreme 25,000 lumens for illumination at the level of vehicle headlights.Extreme range: Up to 630 metres light range for identifying objects at long distances.Self-sufficient energy source: Integrated, rechargeable battery pack with eight high-performance rechargeable batteries.Intelligent control: Eight precisely selectable light levels with real-time display for power and battery status.Maximum safety: Active heat management and proximity sensors to prevent overheating.Powerful in professional large-scale operationsThe X9R Marauder was developed for situations in which conventional torches are not sufficient. Fire brigades and search and rescue services (SAR) can be used to illuminate entire disaster areas, extensive wooded areas or unclear accident sites. For the Coastguard and maritime operations the powerful beam penetrates haze and darkness to search for people or objects on the water. In the industrial sector it is used for large-scale inspections of industrial plants, open-cast mining areas or for monitoring large company premises by Security services.Intelligent technology for extreme performanceAt the heart of the X9R Marauder are six XHP70.2 LEDs, which use an advanced lens system to create an optimised light cone for area and range. To ensure that the enormous power is always available safely, the lamp has an active heat management system with internal liquid cooling and external cooling fins. The permanently installed battery pack consisting of eight 18650 high-performance rechargeable batteries provides the necessary energy and is quickly recharged via a powerful mains or car adapter.Safety and control at the highest levelWith an output of 25,000 lumens, safety is the top priority. The X9R Marauder has an intelligent proximity sensor that automatically reduces the light output when an object approaches the lamp head, to prevent heat damage. It is operated via a single, multifunctional side switch. A digital display next to the switch provides real-time information about the selected light level, the remaining power in lumens and the exact battery level, which enables precise application planning. Features  ModelOLight X9R Marauder Product typeHigh performance LED headlamp Max. Light output (lumens)25000 Max. Light range (metres)630 Light intensity (candela)99225 Power supplyIntegrated battery pack (8x 18650) Charging typeDC power adapter WaterproofnessIPX7 Housing materialAluminium alloy Dimensions (L x Ø head, mm)320 x 100 Weight (g)approx. 1855 (incl. battery) Special featuresActive heat management, proximity sensor  FAQs about the OLight X9R MarauderFor which professional groups is this searchlight designed?The X9R Marauder is a specialised tool for professional users who require maximum light output. This primarily includes fire brigades, THW, search and rescue services (SAR), coast guards, police, security services for large facilities and industrial inspectors.How is overheating prevented at 25,000 lumens?The lamp utilises a multi-stage protection system. An active heat management system monitors the temperature and gradually reduces the output if necessary. In addition, a proximity sensor immediately reduces the output if the light beam is blocked.Is the battery replaceable?No, the battery pack is designed as a permanently integrated and sealed unit to ensure maximum performance, safety and waterproofness. It is charged via the supplied charging adapters.How long does it take to fully charge the battery?Thanks to the powerful charging adapter, the charging time for the fully discharged battery pack is approx. 3 hours.How is the lamp transported?Due to its size and weight, the OLight X9R Marauder is supplied in a robust, waterproof transport case. A practical shoulder strap is also included for use in the field, making it easier to carry.

The OLight Warrior X 4 is a professional, tactical LED spotlight designed for maximum range and uncompromising reliability in demanding operational scenarios. Its design focuses on the key tactical requirements: a highly focused light beam for identifying the most distant targets and operation reduced purely to the rear switch for intuitive handling under stress. With an innovative dual charging system and its extremely robust construction, the Warrior X 4 is the ideal instrument for police, security services and hunters.Highlights at a glanceExtreme range: Up to 630 meters beam range for reliable identification of targets at long distance.Purely tactical operation: All functions are controlled via a single, two-stage and multifunctional tail switch.Dual charging system: Offers both the proven magnetic charging connector and a concealed, waterproof USB-C connector.Maximum robustness: Powerful stainless steel bezel and increased drop resistance from 2 meters height.High performance: Up to 2,600 lumens luminous flux for intensive and far-reaching illumination.Powerful in tactical long-distance applicationsThe Warrior X 4 was specifically developed for professional users for whom a high range is crucial. For police and border security it enables the monitoring of large, open areas and the identification of persons or vehicles from a safe distance. security services responsible for large areas such as industrial plants, airports or solar parks can use the Warrior X 4 to quickly and effectively control the entire perimeter. In the hunting field it is used for reliably targeting game at long distances.Uncompromising control for tactical operationsThe operating concept of the Warrior X 4 is deliberately designed for simplicity and speed under stress and dispenses with a side switch. All lighting functions are controlled via the metal tail switch. A light press activates the low mode for close range, a firm press immediately switches to turbo mode for maximum range. This ensures that in critical situations, the correct light mode is always available intuitively and without delay.Robust construction with innovative charging conceptThe housing made of high-strength aluminium alloy is designed for the toughest operating conditions. The front bezel made of stainless steel not only protects the optics, but can also be used as a glass breaker in emergency situations. A technological highlight is the innovative charging connector: In addition to the familiar magnetic OLight charging cable, a waterproof USB-C port is concealed under a rotatable protective ring at the end of the torch. This provides maximum charging flexibility in professional everyday life, as the torch can be charged with any standard USB-C cable. Features  ModelOLight Warrior X 4 Product typeTactical LED spotlight Max. light output (lumens)2600 Max. beam distance (meters)630 Light intensity (candela)99310 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging typeUSB-C Water resistanceIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)149 x 39.5 Weight (g)approx. 249 (incl. battery) Special featuresTactical tail switch, glass breaker  FAQs about this Tadiran batteryIs this battery rechargeable?No, this is a primary lithium battery and must not be recharged under any circumstances. Attempting to charge the cell is dangerous and may result in overheating, leakage or bursting of the cell.What does the 'axial wire' connection mean?This model is equipped with connecting wires that exit from the centre of the positive and negative poles of the cell and run in opposite directions along the longitudinal axis. This configuration allows for very flexible mounting and direct soldering to the electronics without the need for a battery holder.What does the passivation effect mean with this battery?After prolonged storage, a protective layer forms on the lithium surface, which minimises self-discharge. On first load, this layer can cause a short voltage delay. For applications that require high current pulses immediately, suitable circuit designs or special battery types should be considered.For which devices is this battery type suitable?This type of battery is intended exclusively for professional and industrial electronics. These include, among others, meters, memory backup, security technology, medical devices and sophisticated tracking systems where the battery is soldered directly.How long is the battery shelf life and how should it be stored?The battery has a shelf life of over 10 years. For maximum shelf life, we recommend storage in a cool and dry place with low humidity.

The OLIGHT Marauder 2 is a professional high performance hand torch designed as the ultimate tool for illumination at the highest level. It offers a revolutionary dual light system with an extreme 14,000 lumen floodlight for area illumination and a sharply focused 800-metre high beam for distance. With its integrated, powerful battery pack and USB-C power bank function, the Marauder 2 is not only a light source, but also a self-sufficient power hub for the most demanding applications in the fields of search and rescue, security and industry.Highlights at a glanceExtreme performance: Up to 14,000 lumens floodlight and 800 metres range in high beam mode.Integrated power bank: Serves as a self-sufficient power source for charging mobile devices via USB-C.Innovative dual light system: Easy change between maximum area illumination and extreme range.Intuitive operation: Quick change of light type via toggle switch and 7-stage brightness control via rotary switch.Fast charging: Powerful USB-C charging port (30W) for short charging times.Powerful in professional large-scale operationsThe Marauder 2 has been developed for scenarios where maximum light output and flexibility are essential. Search and rescue services and fire brigades can illuminate entire accident sites as bright as day using the floodlight and search distant areas with the high beam. During industrial inspection of infrastructure such as bridges, dams or wind turbines, the high beam enables safe inspection from a great distance. For security services and authorities it is used for extensive monitoring of terrain. The power bank function is a critical feature to keep communication devices ready for use in the field.Two specialised light profiles for maximum performanceThe heart of the Marauder 2 is its advanced optical system. Twelve high-performance LEDs are arranged in a ring and, thanks to a special lens matrix, produce an extremely wide and homogeneous floodlight. In the centre is a separate, high-intensity LED with a converging lens that produces a sharply focused light beam for maximum range. The toggle switch allows seamless switching between these two optimised light profiles.Intelligent energy management and intuitive controlThe permanently installed battery pack consisting of three 21700 lithium-ion batteries offers an enormous energy reserve of 54Wh. The bidirectional 30W USB-C port enables not only extremely fast charging of the torch itself, but also charging external devices such as smartphones, tablets or GPS devices. The innovative 3D rotary switch, surrounded by seven-stage LED indicators for brightness and battery status, enables precise and always readable control of all functions.Features  ModelOLight Marauder 2 Product typeHigh performance hand torch Max. light output (lumens)14000 (floodlight) / 850 (high beam) Max. beam distance (metres)450 (floodlight) / 800 (high beam) Light intensity (candela)160000 Power supplyIntegrated battery pack (54Wh) Charging typeUSB-C (Power Delivery) Water resistanceIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)140 x 79 Weight (g)approx. 750 (incl. battery) Special featuresPower bank function, proximity sensor  FAQs about the OLight Marauder 2How does the power bank function work?The USB-C port of the Marauder 2 is bidirectional. To charge external devices, simply connect them to the torch with an appropriate cable. The Marauder 2 recognises the connected device and supplies power to charge it. This is ideal for providing power to communication devices or other important electronics in use.What is the main difference to the Marauder Mini?The main difference lies in sheer power and functionality. The Marauder 2 provides double the floodlight output (14,000 vs 7,000 lumens), a greater range (800m vs 600m), and features the crucial USB-C power bank function. The Mini is optimised for compactness, while the Marauder 2 is designed for maximum performance and self-sufficiency.Does the torch have safety functions at this performance?Yes, the Marauder 2 is equipped with a number of protective mechanisms. Intelligent heat management reduces output if the temperature is too high to avoid damage. A proximity sensor automatically dims the light if an object comes too close to the lamp head, to prevent glare and fire hazards.How can I recognise the charging and brightness status?Around the rotary switch there are two rows of LED indicators. One row shows the selected brightness level (level 1 to 7), the other row shows the remaining battery charge in real time.How is the torch protected against unintentional switching on?By turning the switch by more than 90 degrees, a mechanical lock is activated that reliably prevents accidental switching on during transport.

The OLIGHT Baton Turbo is the top-of-the-line, high-performance model in the Baton series, designed for professionals who need maximum power in a compact EDC (Everyday Carry) format. It combines extreme brightness with a long runtime and the proven, robust features of the Baton family. This version in OD Green (olive green) is ideal for tactical operations and use in the great outdoors where inconspicuous equipment is required.Highlights at a glanceExtreme brightness: An exceptionally high light output for a lamp of this size, ideal for illuminating large areas.Tactical colour scheme: The OD Green housing ensures low visibility in outdoor environments.Superior runtime: Powered by a high-energy lithium-ion battery for long-lasting use.Intelligent protection sensor: An integrated proximity sensor protects against overheating in the event of accidental activation.Flexible use: Two-way clip and a strong magnetic end cap enable versatile, hands-free application scenarios.Powerful in professional applicationsThe Baton Turbo was designed for situations in which a compact lamp has to deliver the performance of a larger model. Security forces at night patrols can use the turbo mode to intensely and quickly illuminate suspicious areas. Rescue and emergency services use it as a powerful first light at accident scenes, which can be easily worn on the uniform. For Industrial technicians inspecting large, dark facilities, it provides the necessary brightness without blocking your hands.Advanced technology for maximum performanceAt the heart of the Baton Turbo is a high-performance LED that, with a TIR lens, creates a wide yet powerful beam. A specially adapted high-capacity lithium-ion battery provides the energy needed for impressive performance and long runtimes. An intelligent proximity sensor constantly monitors the distance in front of the lens and automatically reduces output to prevent overheating in pockets or holsters and maximise safety.Ergonomic design for everyday professional useDespite its enormous power, the Baton Turbo retains the ergonomics and compactness of the Baton series valued by professionals. The housing made of high-quality aluminium alloy is provided with a grippy texture for a secure grip even with gloves. Operation is via an enlarged, intuitive side switch that enables quick selection of the different brightness levels while indicating the battery charge status. Features  ModelOLight Baton Turbo Product typeHigh performance LED torch Max. light output (lumen)2500 Max. beam distance (metres)145 Light intensity (candela)5295 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging methodMagnetic charging connector (MCC3) Waterproof ratingIPX8 Housing materialAluminium alloy Dimensions (L x Ø, mm)114 x 26 Weight (g)approx. 148 (incl. battery) Special featuresProximity sensor, Magnetic end cap  FAQs about the OLight Baton TurboWhat distinguishes the "Turbo" model from other Baton lamps?The "Turbo" model is consistently designed for the highest luminous output within the compact Baton format. It usually uses a larger battery and a more powerful LED than the standard models to achieve superior brightness and range for demanding professional users.What is the advantage of the OD Green colour?The OD Green (olive green) colour is a classic tactical colour. It reduces reflections and ensures the equipment is less conspicuous in natural environments such as forests or rural areas. This is particularly advantageous for security personnel or in official use.How does the proximity sensor work?The sensor detects when an object is directly in front of the lens and automatically dims the light to a low level. This prevents overheating if accidentally switched on in a pocket and protects the user from strong glare during close-range work.For which professional groups is this high power in a compact lamp useful?It is ideal for professional users who often need to quickly illuminate a large area but cannot or do not wish to carry a large lamp. This includes police officers on patrol, paramedics, security personnel and mobile technicians.How is the lamp secured against unintentional activation?The lamp features an electronic lock function. This is activated by pressing and holding the side switch when the lamp is switched off and reliably prevents accidental activation during transport.

The OLight Arkfeld Ultra is an innovative and multifunctional 3-in-1 lighting tool, developed to meet the highest professional demands. In a unique, ultra-flat housing, it combines a powerful torch with neutral white light, a practical UV light and an eye-safe class 1 green laser. The intuitive selection of the light source via a central rotary switch makes the Arkfeld Ultra the ideal companion for presentations, inspections, expert opinions and technical field service.Highlights at a glance3-in-1 functionality: Combines powerful white light, 365nm UV light and a green class 1 laser in one device.Eye-safe laser: Class 1 laser (<0.39mW) for safe professional use in presentations and as a target pointer.Powerful white light: Up to 1,300 lumens for bright and clear illumination with colour-true, neutral white light.Flat pocket design: Compact, rectangular housing with clip that can be carried comfortably without rolling.Intuitive operation: Central rotary switch for quick and clear selection of the desired light source.Powerful in a wide range of professional applicationsThe Arkfeld Ultra is a versatile instrument that optimises workflows in numerous industries. In presentations and training the green laser, which is clearly visible in daylight, serves as a professional pointer. Technicians, inspectors and appraisers use the bright white light for general inspection, the UV light to detect leaks or counterfeits and the laser for precise marking of defects from a distance. In logistics and warehousing the laser makes it easier to point to high goods, while the white light helps when reading documents.Innovative design and intuitive controlThe unique selling point of the Arkfeld Ultra is its flat, rectangular design. Not only does it prevent rolling away on smooth surfaces, but it also enables extremely comfortable carrying in shirt or trouser pockets. Operation is geared towards efficiency: a central ring around the main switch allows quick and precise switching between the three light sources (white light, UV, laser) without having to click through different modes.Safety and professional benefits in detailThe integrated green laser of class 1 is classified as eye-safe for normal use according to international standards. This enables unrestricted use in professional environments without having to comply with the strict safety regulations for more powerful lasers (class 2 or 3). The 365nm UV light is another professional tool, ideal for checking security features on documents and banknotes, crack testing or leak detection with fluorescent contrast agents. Features  ModelOLight Arkfeld Ultra Product typeLED light with UV & laser Max. light output (lumens)1000 Max. light range (metre)100 UV light900mW at 365nm LaserClass 1 (<0.39mW) Power supplyIntegrated battery (1500 mAh Li-Po) Charging typeMagnetic charging connection (MCC) WaterproofnessIPX7 Housing materialAluminium alloy Dimensions (L/W/H, mm)120 x 27 x 16 Weight (g)approx. 111 Special featuresThree light sources, function selector switch  FAQs for the OLight Arkfeld UltraWhat does "Class 1 Laser" mean and what is the advantage?Class 1 is the highest safety level for laser products. It means that the laser is harmless to the human eye under normal and foreseeable use. The advantage in a professional environment is that no special laser safety officers or protective measures are required, which makes its use considerably easier.How do I select between white light, UV light and laser?The selection of the light source is simple and direct via the rotary switch surrounding the main button. By turning the ring to the corresponding symbol, the function is preselected and then activated with the main button.Is the green laser visible in daylight?Yes. Green laser light is significantly more visible to the human eye than red light, especially in bright ambient conditions. This makes it a superior tool for presentations or pointing at objects in daylight.For which inspection tasks is the UV light suitable?The 365nm UV light is ideal for checking security features on banknotes and ID cards, for leak detection using fluorescent contrast agents in air conditioning and hydraulic systems, for crack testing of materials, and for revealing organic traces in forensics or hygiene management.What is the main advantage of the flat design?The rectangular design prevents the light from rolling off surfaces. In addition, it allows for a very comfortable and inconspicuous carry in a pocket, similar to a pen or a small tool, as opposed to conventional round torches.

The OLight Perun 3 is a multifunctional and extremely powerful LED lamp designed for professional users who require hands-free working at the highest level. It combines the functionality of a headlamp with the flexibility of a hand-held angle lamp and a magnetic work light. With an impressive brightness of up to 2,500 lumens, an intelligent safety sensor and an additional red light mode, the Perun 3 is an indispensable tool for industry, trade, emergency services and security personnel.Highlights at a glanceMultifunctional design: Can be used as a headlamp, hand lamp or magnetic work light.High light output: Up to 2,500 lumens for wide and very bright illumination of the work area.Integrated red light: Separate red light mode to maintain night vision and for signalling purposes.Intelligent protection sensor: Automatically reduces the brightness when obstacles are near to prevent glare.Convenient charging: Proven magnetic charging port at the end of the lamp for easy charging.Powerful in professional applicationsThe Perun 3 is designed for work assignments where both hands must remain free. Industrial technicians and craftsmen use it to illuminate machines and equipment, with the magnetic end cap allowing flexible positioning on metallic surfaces. Rescue services and fire brigades appreciate the high light output for use in the dark and the option to carry the lamp on the head or equipment. For Security services it is a versatile tool for inspections and patrols where the red light mode ensures discreet illumination.Maximum flexibility for hands-free workingThe core of the Perun 3 is its versatility. With the comfortable and breathable headband, it becomes a fully-fledged headlamp. With one movement, the lamp body can be removed from the holder and used as a powerful, hand-held angle lamp. The strong magnetic end cap expands the range of applications by allowing secure attachment to vehicles, switch cabinets or steel girders, to illuminate the work area perfectly and stationary.Intelligent technology for safe useFor professional use, the Perun 3 is equipped with intelligent features. An advanced proximity sensor detects when an object is directly in front of the lens (e.g. a wall or a document) and automatically dims the brightness. This protects against glare and prevents excessive heat. The dedicated red light mode not only preserves night vision, but also reduces attraction for insects and is ideal for team use to avoid dazzling others. Features  ModelOLight Perun 3 Product typeLED head and angle lamp Max. light output (lumens)2500 Max. beam range (metres)155 Light intensity (candela)6000 Additional light colourRed light Power supply1x 21700 Li-Ion battery, 4000 mAh Charging methodMagnetic charging port (MCC3) Waterproof ratingIPX8 Housing materialAluminium alloy Dimensions (L x Ø, mm)112 x 26 Weight (g)approx. 147 (incl. battery) Special featuresMagnetic end cap, proximity sensor  FAQs about the OLight Perun 3How does the Perun 3 differ from a conventional headlamp?The Perun 3 offers significantly higher brightness and a more robust metal construction compared to many plastic headlamps. Its key advantage is the 3-in-1 design: it can be worn on the head, used as a hand lamp, and magnetically attached to surfaces, greatly expanding its versatility.What is the red light mode used for in professional applications?Red light preserves the eyes' ability to see in the dark (night vision). It is ideal for pilots, security staff or technicians who need to read maps or instruments at night without blinding themselves. It also disturbs many animals and insects less than white light.How does the safety sensor work?The sensor continuously measures the distance to objects in front of the lens. If an object comes too close, the lamp automatically reduces the brightness to a low level. This prevents overheating in the event of accidental activation in a bag and protects the user from intense glare when working close up.Is the magnet in the end cap strong enough to securely hold the lamp?Yes, the magnet in the end cap is a strong neodymium magnet designed to securely hold the entire weight of the lamp in any orientation on flat, ferrous metal surfaces.How is the lamp protected against unintentional switching on?The Perun 3 has an electronic lock feature. By pressing and holding the switch when turned off, the lamp is locked and cannot be inadvertently activated, for example, in a bag or toolbox.

The OLight Seeker 4 Pro in OD Green is a high-performance, rechargeable LED torch designed for demanding professional use. It combines extreme brightness with a robust construction and intuitive operation. An innovative metal rotary switch enables precise, stepless brightness control. With its resilient construction and intelligent charging system, the Seeker 4 Pro is a reliable tool for security services, industry, emergency services and authorities.Highlights at a glanceExtreme brightness: Up to 4,600 lumens of luminous power for broad and intensive illumination.Tactical colouring: The OD Green (olive green) housing ensures low visibility in outdoor environments.Intuitive operation: Stepless dimming via a robust metal rotary switch for precise light control.Robust and reliable: Housing made from a durable aluminium alloy, IPX8 waterproof.Intelligent charging system: Includes multifunctional holster charging station for stationary operation.Powerful in professional applicationsThe Seeker 4 Pro was developed for professional users for whom reliability and performance are crucial. For security services and authorities, the turbo mode enables large areas to be illuminated, while the OD Green colour ensures discreet carrying. In industrial maintenance, the high luminous power makes it easier to inspect systems even from a distance. rescue services and outdoor professionals benefit from the robust, waterproof construction and easy operation even with gloves.Innovative technology for professional useAt the heart of the Seeker 4 Pro is its well thought-out operating concept. The side metal switch is used not only for switching on and off, but also allows stepless and precise adjustment of the brightness for any situation. The high-performance 21700 lithium-ion battery included guarantees long operating times. The unique charging holster can be permanently mounted on a wall or in a vehicle and automatically charges the lamp as soon as it is inserted. This ensures readiness for use at all times.Focus on safety and durabilitySafety functions are essential for professional use. An integrated proximity sensor automatically reduces the light output when the light is directed at a nearby object to prevent overheating or damage. An electronic lock prevents the torch from being switched on unintentionally during transport. The housing, made of high-quality aluminium alloy, is not only waterproof to IPX8 standard, but also drop-resistant up to 1.5 metres. Features  ModelOLight Seeker 4 Pro Product typeProfessional LED torch Max. Light output (lumens)4600 Max. Range (metres)260 Light colourCool white (5700K - 6700K) Light intensity (candela)16900 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging methodUSB-C and magnetic charging connection WaterproofingIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)133 x 35 Weight (g)approx. 205 (incl. battery) Special featuresStepless brightness control  FAQs about the OLight Seeker 4 ProWhat is the advantage of the OD Green colouring?The OD Green (olive green) colour is a classic tactical colour. It reduces reflections and ensures that the equipment is less conspicuous in natural environments such as forests or rural areas. This is especially advantageous for security personnel, hunters or for official use.For which professional groups is the Seeker 4 Pro especially suitable?It is ideal for security personnel, industrial and maintenance technicians, utility workers, police officers, emergency services and all professional users who need a robust and extremely bright torch with intuitive operation.How does the charging holster work?The supplied holster can be mounted on a wall (e.g. in a workshop or guardhouse) or in a vehicle. It has a charging connection. As soon as the torch is inserted into the holster, it is automatically charged and is therefore always ready for the next use.What does the built-in proximity sensor do?The sensor is a safety feature. It detects when the head of the torch is very close to an object (e.g. in a bag or when accidentally covered) and automatically reduces the brightness to prevent overheating and possible damage.How is the torch protected against unintentional switching on?The Seeker 4 Pro is equipped with an electronic lock. By pressing and holding the button when the torch is switched off, it is locked and cannot be accidentally activated, for example in a bag or suitcase.

The OLight Seeker 4 Pro in Desert Tan is a high-performance, rechargeable LED torch designed for demanding professional use. It combines extreme brightness and range with a robust design and intuitive operation. An innovative metal rotary switch enables precise, infinitely variable brightness control. With its robust construction and intelligent charging system, the Seeker 4 Pro is a reliable tool for security services, industry, emergency services and authorities.Highlights at a glanceExtreme brightness: Up to 4,600 lumen light output for maximum illumination and range.Professional colour scheme: The housing in Desert Tan (sand colour) is suitable for special environments.Intuitive operation: Stepless dimming via a robust metal rotary switch for precise light control.Robust and reliable: Housing made of a durable aluminium alloy, IPX8 waterproof.Intelligent charging system: Including multifunctional holster charging station for stationary use.Powerful in professional applicationsThe Seeker 4 Pro was developed for professional users for whom reliability and performance are crucial. For Security services and authorities the turbo mode enables the illumination of large areas at maximum distance, while the Desert Tan colour offers a suitable option for operations in arid regions. In industrial maintenance the high luminosity facilitates the inspection of large installations and dark areas. rescue services benefit from the robust, waterproof construction and easy operation even with gloves.Innovative technology for professional useThe heart of the Seeker 4 Pro is its sophisticated operating concept. The side metal switch is not only used to switch the torch on and off, but by turning it, allows stepless and precise adjustment of the brightness to any situation. The included high-performance 21700 lithium-ion battery ensures long operating times. The unique charging holster can be permanently mounted on a wall or in a vehicle and automatically charges the torch as soon as it is plugged in. This ensures that it is always ready for use.Focus on safety and durabilityFor professional use, safety features are essential. An integrated proximity sensor automatically reduces the light output when the light is directed at a nearby object to avoid overheating or damage. An electronic lock function prevents unintentional switching on of the lamp during transport. The housing, made from a high-quality aluminium alloy, is not only waterproof according to IPX8 standard, but also protected against drops from up to 1.5 metres. Features  ModelOLight Seeker 4 Pro Product typeProfessional LED torch Max. light output (lumens)4600 Max. beam range (metres)260 Light colourCool white (5700K - 6700K) Light intensity (candela)16900 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging methodUSB-C and magnetic charging port WaterproofIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)133 x 35 Weight (g)approx. 205 (incl. battery) Special featuresStepless brightness control  FAQs about the OLight Seeker 4 ProWhat is the difference between cool white (CW) and neutral white (NW)?Cool white light (CW), as used in this model, is perceived by the human eye as brighter and maximises perceived brightness and range. In contrast, neutral white (NW) offers a more natural colour rendering, which can be an advantage for inspection tasks.For which professional groups is the Seeker 4 Pro particularly suitable?It is ideal for security personnel, industrial and maintenance technicians, employees of utility companies, police officers, emergency services and all professional users who require a robust and extremely bright torch with intuitive operation.How does the charging holster work?The supplied holster can be mounted on a wall (e.g. in a workshop or guardhouse) or in a vehicle. It contains a charging port. As soon as the torch is placed into the holster, it is automatically charged and is therefore always ready for the next use.What does the built-in proximity sensor do?The sensor is a safety feature. It detects when the lamp head is very close to an object (e.g. in a pocket or if accidentally covered) and automatically reduces the brightness to prevent overheating and possible damage.How is the torch secured against accidental switch-on?The Seeker 4 Pro features an electronic lock function. By holding the switch down when switched off, the torch is locked and cannot be activated accidentally, for example in a bag or suitcase.

The OLIGHT Oclip Pro is an extremely compact, versatile and rechargeable LED light designed as a flexible tool for everyday professional use. It offers powerful and wide illumination for close range as well as a switchable red light for special applications. Thanks to its innovative mounting system with a robust clip and a strong magnetic base, the Oclip Pro enables hands-free working in almost any situation. It is the ideal additional light for technicians, logistics personnel and security staff.Highlights at a glanceFlexible attachment: Strong clip for fastening to clothing, caps, belts and equipment.Magnetic base: Attaches securely to all magnetic surfaces for hands-free working.Additional red light: Switchable to red continuous light (night vision) or flashing light (warning signal).Powerful white light: Up to 500 lumens for bright and wide illumination of the work area.Compact and rechargeable: Lightweight, robust design with practical USB-C charging port.Powerful in a variety of professional applicationsThe Oclip Pro was developed for situations where both hands must remain free for work. Industrial and service technicians attach it magnetically inside switch cabinets or on machines to precisely illuminate maintenance work. Logistics and warehouse staff clip it to their vests to read delivery notes or barcodes in the dark without having to hold a hand lamp. Security and rescue services use the white light for documentation or the red flashing light as a personal safety and warning signal to be clearly visible in operation.Thoughtful design for everyday professional useThe heart of the Oclip Pro is its multifunctional clip. It is not only used for attachment, but also protects the USB-C charging port from dust and moisture. The strong magnetic base of the clip transforms any metallic surface into a lamp holder. The housing is made from a lightweight yet resilient aluminium alloy and plastic to withstand the demands of everyday use and is splash-proof to IPX5 standard.Versatile light modes for every taskThe Oclip Pro offers different, easily selectable light levels for the white main light to provide the right brightness for every task. The additional red light is a crucial feature for professional users. The red steady mode preserves the eyes' natural night vision and is ideal for reading maps or instruments in the dark. The red flashing mode serves as a highly visible emergency signal or for marking your own position in poor visibility conditions. Features  ModelOLight Oclip Pro Product typeMobile LED small lamp Max. light output (lumens)400 Max. lighting range (metres)85 Additional light colourRed light (steady / flashing) Power supplyIntegrated battery (400 mAh Li-Po) Charging typeUSB-C WaterproofIPX5 Housing materialAluminium alloy Dimensions (L/W/H, mm)55 x 47 x 22 Weight (g)approx. 57 Special featuresClip and strong magnetic base  FAQs about the OLight Oclip ProHow do you switch between white and red light?Hold the switch for one second when the light is on. The light then switches seamlessly between the white and red light mode.For which professional activities is the magnetic base particularly useful?The magnetic base is ideal for all work on metallic objects. Car mechanics can attach the light to the bonnet, electricians inside control boxes, and plant mechanics directly to the machine that needs maintenance.What is the red flashing light used for?The red flashing light serves as a personal warning and safety signal. It increases the visibility of staff during night operations, for example during roadworks, on company premises or during rescue work, and can be used as an emergency signal.How can I check the battery status of the light?The Oclip Pro has a battery charge level indicator. Briefly press the switch once in the off state. A green indicator signals a battery level above 10%, a red indicator signals a level below 10%.Is the clip robust enough for everyday use?Yes, the clip is made of resilient metal and features a strong spring to ensure a secure hold on thicker work clothing, belts, or equipment. 

The OLIGHT Marauder Mini is an extremely powerful and versatile LED torch designed as a compact powerhouse for the most demanding professional applications. Its innovative light system offers both a 7,000 lumen floodlight for wide illumination of close areas and a concentrated high beam with a range of 600 metres. This version in robust OD Green (olive green) is ideal for tactical operations and use in the great outdoors.Highlights at a glanceInnovative dual light system: Easily selectable between 7,000 lumen floodlight and 600 metre high beam.Tactical colour scheme: The OD Green (olive green) housing ensures low visibility in outdoor environments.Additional RGB LEDs: Integrated red, green and blue light for special applications.Intuitive operation: Quick change of light type and brightness control via rotary switch.Clear status display: Clearly readable indicators for brightness level, battery level and light mode.Powerful in professional applicationsThe Marauder Mini is the ideal tool for professional users who need to be prepared for any situation. Rescue and search services can illuminate a large search area with the floodlight and identify distant objects with the high beam. With the industrial inspection of large installations or overhead lines, the high beam enables inspection from a safe distance. For security services and authorities the floodlight offers full control over large areas, while the OD Green colour supports discreet carrying.Two light profiles for every situationThe centrepiece of the Marauder Mini is its dual lens system. Nine LEDs are arranged around a central lens and produce an extremely wide and even floodlight for close range. The central high-performance LED produces an extremely focused and long-range high beam through a converging lens. In contrast to conventional zoom systems, this solution offers a perfect, artefact-free light beam for both applications, free from compromise.Intuitive controls and professional featuresThe operation is designed for quick and safe handling in use. A simple toggle switch toggles between high beam, floodlight and RGB mode. The easy-grip 3D rotary switch enables rapid selection of brightness levels. Clearly visible LED indicators next to the switch always show the selected mode, brightness and battery status. An integrated vibration motor gives a tactile warning when the battery is low, so the warning is noticeable even in the dark or when wearing gloves. Features  ModelOLight Marauder Mini Product typeLED torch with flood/high beam Max. Light output (lumen)7000 (floodlight) / 900 (high beam) Max. Lighting range (metres)310 (floodlight) / 600 (high beam) Light intensity (candela)90000 Additional light coloursRed, Green, Blue (RGB) Power supply1x 32650 Li-Ion battery, 6500 mAh Charging methodMagnetic charging connector (MCC3) WaterproofnessIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)130 x 65.6 Weight (g)approx. 462 (incl. battery)  FAQs about the OLight Marauder MiniWhat is the advantage of the OD Green colour?The colour OD Green (olive green) is a classic tactical colour. It reduces reflections and ensures that the equipment is less conspicuous in natural environments such as forests or rural areas. This is a particular advantage for security personnel, hunters or in official use.What are the coloured RGB LEDs used for in practice?Red light preserves night vision and is used by pilots or in tactical applications. Green light is often used for hunting or reading maps because it is harder for wildlife to see. Blue light can be used to make liquids visible, such as blood or sweat, in forensics.What is the advantage over a normal torch with zoom function?A zoom torch always has to compromise on light quality. The Marauder Mini uses two separate, perfectly matched optical systems. This gives you a flawless, wide floodlight and a sharply focused high beam without the optical disadvantages of a zoom lens.How does the torch warn when the battery is low?In addition to the visual display, the handle of the torch vibrates when the battery level becomes critical (below 10%). This haptic feedback ensures that you notice the warning even if you are not looking at the torch or are wearing gloves.Is the battery replaceable?No, the Marauder Mini's high-performance battery pack is permanently integrated into the housing to ensure maximum performance, robustness and waterproofing. The torch is conveniently charged using the supplied magnetic charging cable.

The OLIGHT Warrior 3S is a professional tactical LED torch designed for uncompromising performance and reliability in demanding operational scenarios. It features an innovative two-switch system that enables intuitive operation both in tactical and everyday situations. This version in OD Green (olive green) offers optimised camouflage in natural environments and is the ideal tool for security services, authorities and emergency services.Highlights at a glanceTactical two-switch system: Rear switch for instant access to turbo/strobe and side switch for everyday use.High performance: Up to 2,300 lumens of light output and an impressive beam distance of up to 300 metres.Tactical colour scheme: The housing in OD Green for unobtrusive use in outdoor environments.Maximum robustness: Housing made from high-strength aluminium alloy with impactful bezel, IPX8 waterproof.Intelligent safety functions: Integrated proximity sensor for power reduction when obstacles are detected.Powerful in tactical applicationsThe Warrior 3S was developed for professional users for whom quick and reliable light output is crucial. For security services and security staff the rear switch enables instant access to maximum brightness for illuminating danger zones. The OD Green colour helps to carry the equipment inconspicuously. Police and other authorities value the intuitive tactical operation and the sturdy bezel as a versatile tool. Emergency and rescue forces can use the high output to illuminate large accident sites.Intuitive operation for every situationThe Warrior 3S's two-switch system separates tactical and administrative functions. The two-stage rear switch is optimised for use under stress and allows instant access to medium and maximum output. The side switch enables the comfortable selection of regular brightness levels for everyday use. Clear LED indicators around the side switch always show the selected level and battery status.Engineered for the toughest operating conditionsThe Warrior 3S housing is made from a durable aluminium alloy and features a grippy texture for a secure hold, even with gloves. The toothed bezel (strike ring) made of stainless steel not only protects the lens, but can also be used in emergencies. The lamp is fully waterproof to IPX8 standard. An intelligent proximity sensor detects when an object is directly in front of the lens and automatically reduces the output to avoid heat damage.Features  ModelOLight Warrior 3S Product typeTactical LED torch Max. light output (lumens)2300 Max. beam distance (metres)300 Light intensity (candela)23000 Power supply1x 21700 Li-Ion battery, 5000 mAh Charging methodMagnetic charging connector (MCC3) Waterproof ratingIPX8 Housing materialAluminium alloy Dimensions (L x Ø head, mm)139 x 29.5 Weight (g)approx. 176 (incl. battery) Special featuresTactical rear switch, proximity sensor  FAQs about the OLight Warrior 3SWhat is the advantage of the OD Green colour?The OD Green (olive green) colour is a classic tactical shade. It reduces reflections and ensures that the equipment is less conspicuous in natural environments such as forests or rural areas. This is a particular advantage for security personnel, hunters or official use.What is the advantage of the two-switch system?It separates operation for stressful situations from normal use. The rear switch is designed purely for fast, tactical use (maximum brightness, strobe). The side switch allows convenient and easy selection of various brightness levels for administrative tasks.Can I use a cable switch for weapon mounting?Yes, the magnetic end cap of the Warrior 3S is compatible with OLight's optional magnetic cable switch. This enables professional use as a weapon light.What is the purpose of the toothed ring (bezel) at the front?The bezel primarily protects the front lens from impacts. In tactical or emergency situations it can be used as a glass breaker or for self-defence.How is the torch protected against accidental activation?The Warrior 3S has an electronic lock-out function. This is activated by pressing and holding the side switch when the torch is off and reliably prevents unintentional activation during transport.

The Fenix TK25UV is an innovative, tactical torch that has been specially developed for professional users in security services, forensics and specialised outdoor activities. Its outstanding feature is the patented dual light source switching: by simply turning the lamp head, you can switch at lightning speed between a powerful white light beam with 1000 lumens and a highly efficient UV light with 3000 mW. This combination makes it the ultimate tool for document examination, trace search and tactical operations.Highlights at a glanceDual light system: Patented rotating mechanism for quick change between white light and UV light.Enormous luminosity: 1000 lumen maximum white light for a range of up to 225 metres.Powerful UV light: 3000 mW power at 365 nm wavelength for optimum fluorescence excitation.Tactical operation: Dual tail switch for momentary, continuous and instant strobe.Flexible energy: Operates with 1x 18650 Li-Ion battery or 2x CR123A batteries (cold-resistant).Extremely robust: Housing made of A6061-T6 aluminium, IP68 waterproof (up to 2m) and shockproof.Two specialists in one lampThe TK25UV combines two completely different application areas without compromise. In white light mode, it is a fully-fledged tactical lamp with four brightness levels and strobe function, ideal for illuminating operational locations or for orientation. A turn of the head activates UV mode: with a wavelength of 365 nm, this light is perfect for making invisible security features on ID cards and banknotes visible, for finding leaks in air conditioning systems, or for detecting organic traces (e.g. when hunting or forensics).Tactical control in any situationThe operating concept is optimised for stressful situations. The tactical main switch at the end of the lamp enables momentary light (light press) or continuous light. The separate function switch allows quick switching between brightness levels and, at any time—even when the lamp is switched off—provides instant access to the dazzling strobe mode. The intelligent memory function stores the last used brightness level.Robustness for professional useMade from high-strength aluminium with a hard-anodised surface, the TK25UV is equipped for tough everyday work. It is completely dustproof and waterproof to IP68. A special clip enables secure attachment to equipment or belt. Features ModelFenix TK25UV (white & UV light) ApplicationTactical, hunting, document checking, trace search (UV) Max. luminosity (white)1000 lumens (Turbo) UV light output3000 mW (365nm wavelength) Max. beam range (m)225 (white light) OperationRotating lamp head for switching between white and UV Power supply1x 18650 Li-Ion battery or 2x CR123A batteries Light source2x CREE XP-G2 S3 (white) + 2x UV LEDs Protection typeIP68 (waterproof to 2m) Special featuresDual tactical tail switch, compatible with cable switch AER-03 Dimensions (L x Ø head x Ø body in mm)142.6 x 40 x 25.4 Weight (g)approx. 156.5 (without battery)  FAQs about the Fenix TK25UVWhat is the 365 nm UV light used for?UV light with a wavelength of 365 nm is the standard for professional applications. It is excellent for checking documents (passports, banknotes), for curing UV adhesives, for leak detection (with contrast agent), for mineral searching and for visualising biological traces or dirt residues during hygiene inspections.How do you switch between UV and white light?Switching is purely mechanical and very intuitive by turning the entire lamp head. This is also possible with gloves and prevents accidentally turning on the wrong mode.Is a battery included?The TK25UV is often supplied without a battery as standard so the user can choose their preferred power source. Please check the specific scope of delivery of the offer. We recommend using a high-quality Fenix 18650 Li-Ion battery for the best performance and economy.Can I also operate the lamp with batteries?Yes, the lamp is compatible with two CR123A lithium batteries. These are particularly durable and cold-resistant, making them an ideal backup solution or for use in extremely low temperatures.

The Olight O'Pen Glow is an innovative multifunctional pen that revolutionises the classic penlight by combining four functions in one elegant aluminium housing: writing, lighting (clip), presenting (laser) and discreet note-taking (tip). It features a rechargeable battery and is charged via a special charging station. Particularly noteworthy is the world’s first LED in the writing tip, which automatically lights up when writing in the dark, without dazzling the surroundings.Highlights at a glance4-in-1 functionality: Combines ballpoint pen, bright clip torch (for the room), LED at the writing tip (for the paper) and a green laser pointer.Illuminated writing tip: A tiny LED (0.2 lumens) right at the refill illuminates the writing area on the paper, ideal for taking notes in the dark without disturbing night vision.Bright clip LED: The main LED integrated into the pocket clip delivers up to 120 lumens, perfect to wear on the breast pocket and work hands-free.Green laser pointer: Integrated at the top end of the pen (class 1), ideal as a pointer for presentations or for marking objects on construction sites.New charging station: No longer charged by cable on the pen, comes with a stylish charging base into which the pen is simply inserted (USB-C port on the base).Bolt-action design: The mechanical L-lock (bolt-action) ensures satisfying and safe extension and retraction of the refill and control of the laser.The Swiss army knife for the officeThis pen solves the problem of having to carry several devices (torch, laser, pen) on you. It is particularly popular with architects, police officers, doctors and in the security industry, where you often have to write in the dark, but would need a hand for the torch. With the O'Pen Glow you have light and pen united in one hand. Features ModelOlight O'Pen Glow (4-in-1 Penlight) ApplicationOffice, presentations, EDC, notes at night Functions (4-in-1)1. Writing pen2. Clip light (for writing)3. Pen tip light (torch)4. Green laser Light outputMax. **120 lumens** (torch) / up to 60 lumens (clip light) LaserClass 1 **Green laser** (more visible and professional than red) Power supplyIntegrated Li-Po battery (110 mAh) Charging systemSeparate charging base (USB-C) - pen is simply inserted Operation (light)Rear switch (light/laser) + bolt-action (extend/retract refill) Dimensions (L x Ø in mm)155 x 12.7 (Feels like a high-quality fountain pen in the hand) RefillStandardised refill (Olight RF-OL182X), replaceable Weight (g)approx. 38 (light enough for the shirt pocket)  FAQs about the Olight O'Pen GlowWhich refills fit the pen?The pen uses special Olight RF-OL182X refills. Due to the design with the tip LED, standard refills (like Parker G2) are often not compatible or may need modification. It’s recommended to use Olight original refills so as not to impair the tip illumination function.Can I charge the pen without the base?No. The pen itself no longer has a USB port (unlike its predecessor O'Pen 2). It has contacts on the tip and housing. The supplied charging base is required to charge. Do not lose it!How do I activate the laser?The laser is operated via the bolt-action switch (the lever to extend the refill). Push the lever up and hold it there to activate the laser. This prevents the laser from remaining switched on and draining the battery.Is the battery replaceable?No, the 110 mAh lithium-polymer battery is permanently built into the top section of the pen and cannot be replaced by the user.

The Deye AI-W5.1-B is a powerful, safe and modularly expandable energy storage module with a capacity of 5.1 kWh. With its robust construction, simple installation and high scalability, it is ideal for residential and commercial photovoltaic systems. Thanks to cobalt-free LiFePO₄ technology and an intelligent battery management system, the module is particularly durable, efficient and environmentally friendly.Highlights at a glanceHigh security: Cobalt-free lithium iron phosphate battery cells (LiFePO₄) Scalable: Up to 6 modules per cluster, 36 modules in total (max. 184 kWh) Flexible deployment: Wall or floor mounting possible, stackable design Long service life: Over 6,000 charge cycles at 90% DOD Robust & weatherproof: IP65 protection rating for outdoor use Convenient: Automatic network, remote maintenance & firmware updatesVersatile energy storage for sustainable projectsWhether for a detached house, multi-family house or commercial business, the Deye AI-W5.1-B covers a wide range of requirements for modern energy storage. The efficient use of renewable energies reduces electricity costs and increases the proportion of self-consumption. The modular system can be easily expanded to keep pace with growing energy demand.Safety & reliability at the highest levelThanks to LiFePO₄ battery chemistry, the energy storage system is particularly safe, thermally stable and durable. The integrated battery management system (BMS) reliably protects against overcharging, overheating and short circuits. Passive cooling without fans enables low-noise and low-maintenance operation, even at temperatures from -20 °C to +55 °C.Easy installation & maintenanceThe flat, stackable design allows flexible placement on the wall or on the floor. No complex cabling is necessary. The modules recognise each other automatically in the system and can be conveniently monitored and updated via remote access.Who is the Deye AI-W5.1-B suitable for?This storage unit is ideal for: Private households that want to expand their solar system flexibly Commercial businesses that require modular and fail-safe storage solutions Installers who rely on simple and time-saving systems Sustainability-conscious users who value pollutant-free components ModelDEYAI-W5.1-B Battery typeLiFePO4 Module capacity (kWh)5.12 Module nominal voltage (V)51.2 Module capacity (Ah)100 System nominal voltage (V)51.2 System operating voltage (V)44.8-57.6 System capacity (kWh)5.12 System usable capacity (kWh)4.6 Charging/discharging current (A) - recommendation50 Charging/discharging current (A) - nominal value100 Charging/discharging current (A) - peak discharge (2 min,25°C)150 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 60 LCD displaySOC%, Power, Total Voltage Communication portCAN2.0, RS485 Humidity5% ~ 90% Altitude≤2000m Enclosure IP ratingIP65 Storage temperature (°C)0 ~ 35 Dimensions (W/D/H, mm)720 * 255 * 300 Weight (kg)127.5 Installation locationFloor mounting Recommended depth of discharge90% Cycle life25 ± 2°C, 0.5C/0.5C, EOL70% ≥ 6000 Warranty10 years CertificationsCE/IEC62619 /VDE2510-50/ UL1973/UL9540A/UN38.3  FAQs on the DEYE AI-W5.1-B energy storage moduleHow much energy is actually usable per module?A single module delivers 5.12 kWh gross capacity. Of this, around 4.6 kWh is usable at a depth of discharge of 90% (DoD), ideal for modular storage solutions with high efficiency.Can I expand the system later?Yes, up to six modules are possible per tower, which corresponds to 30.72 kWh per stack. By connecting up to six towers in parallel, the system can be scaled to a total capacity of around 184 kWh without additional hardware.With which inverters does the module work without an additional interface box?The module is plug-&-play compatible with three-phase Deye hybrid inverters of the low-voltage series. Communication takes place directly via CAN or RS485 without a separate communication box. This is included with the PDU and the base. Without this PDU, the storage block alone cannot be connected to the inverter. Please contact sales if you have any questions.Is active cooling necessary?No, natural convection is sufficient to ensure reliable operation. According to the manual, only an air gap of at least 20 cm behind the module must be maintained so that the heat can dissipate unhindered.Must the module be fully charged before initial commissioning?Yes, an initial charge to 100% is recommended in order to correctly record the State of Charge (SoC). If this step is omitted, deviations in SoC values or an inaccurate charge status display may occur during operation. The storage unit can also be charged via the grid if there is too little solar energy. You can set up this function in the Deye inverter. Scope of delivery Deye AI-W5.1-BATT (Single 5.12 kWh battery module): Module typeThis is a pure expansion module (slave unit) for an existing Deye AI-W5.1-B system. It requires a separate BMS control unit for operation.1 x Deye AI-W5.1-BATT battery module (5.12 kWh)A pure battery module with 5.12 kWh that is stacked on a BMS unit or another battery module.1 x connecting bridge / parallel connection cableShort, robust cables or a fixed bridge to connect this module to an existing module.1 x earthing cable (short)A short protective conductor cable for connection to the earth point of the neighbouring module.1 x installation accessories (tower mounting)Includes screws or locking mechanisms to securely stack the module onto an existing unit.1 x installation instructions for expansion moduleInstructions specifically describing the expansion of an existing tower system.

The OLight Oclip is an extremely compact, versatile and rechargeable LED light designed as a flexible tool for everyday professional use. It offers bright and wide illumination for close range. This version in discreet OD Green (olive green) is particularly suitable for use in outdoor environments. Thanks to its innovative fastening system with a robust clip and a strong magnetic base, the Oclip enables hands-free working in almost any situation.Highlights at a glanceFlexible attachment: Strong clip for attaching to clothing, hats, belts and equipment.Magnetic underside: Adheres securely to all magnetic surfaces for hands-free use.Bright illumination: Up to 300 lumens for clear and wide illumination of the work area.Tactical colour scheme: The OD Green housing ensures low visibility in outdoor environments.Compact and rechargeable: Lightweight, robust design with practical USB-C charging port.Powerful in a wide range of professional applicationsThe Oclip was developed for situations in which both hands must remain free for work. Industrial and service technicians magnetically attach it inside switch cabinets or on machines to precisely illuminate maintenance work. Logistics and warehouse staff clip it to a vest to read delivery notes or barcodes in the dark without having to hold a hand lamp. Security and rescue services or personnel in forestry use it as a compact additional light, with the olive-green colour allowing it to be worn discreetly.Sophisticated design for everyday professional useThe heart of the Oclip is its multifunctional clip. It not only serves for fastening, but also protects the USB-C charging port from dust and moisture. The strong magnetic underside of the clip turns any metallic surface into a lamp holder. The housing is made from a lightweight yet resilient plastic and aluminium alloy to withstand the demands of daily use and is splash-proof to IPX5 standard.Simple operation for everyday workThe Oclip offers various, easily selectable light levels for the white main light to provide the appropriate brightness for any task. All functions are controlled via a single, easily accessible switch. The indicator integrated in the switch shows the current battery level at all times to enable reliable operational planning. Features  ModelOLight Oclip Product typeMobile LED mini light Max. Light output (lumens)300 Max. Lighting range (metres)70 Additional light colourRed light (constant / flashing) Power supplyIntegrated battery (280 mAh Li-Po) Charging typeUSB-C Waterproof ratingIPX5 Housing materialPC, aluminium alloy Dimensions (L/W/H, mm)48.5 x 21 x 23 Weight (g)approx. 30 Special featuresClip and strong magnetic base  FAQs about the OLight OclipWhat is the main difference to the Oclip Pro?The Oclip Pro offers higher maximum brightness (500 lumens compared to 300 lumens) and features an additional red light mode for special uses. The standard Oclip focuses on the essential functions of a versatile, hands-free usable white light work light.What is the advantage of the OD Green colour scheme?The OD Green (olive green) colour is a classic tactical colour. It reduces reflections and ensures that equipment is less conspicuous in natural environments such as forests or rural areas. This is particularly advantageous for security services, foresters, or for official use.For which professional activities is the magnetic base particularly useful?The magnetic base is ideal for all work on metallic objects. Car mechanics can attach the light to the bonnet, electricians inside distribution cabinets, and plant mechanics directly to the machine being serviced.How can I check the battery status of the light?The Oclip features a battery charge indicator. Briefly press the switch once when switched off. A green indicator signals a charge above 10%, a red indicator signals a charge below 10%.Is the clip robust enough for everyday use?Yes, the clip is made of resilient metal and has a strong spring to ensure a secure grip on thicker work clothing, belts, or equipment.

The OLight MCC-1A is the original magnetic USB charging cable designed for a wide range of OLight torches and lamps. It offers a simple, reliable and fast way to ensure your OLight equipment is ready for use. As an indispensable accessory for any professional user, it is ideal as a replacement cable or as a second cable for the office, vehicle or workshop to ensure maximum availability of lighting tools.Highlights at a glanceMagnetic charging connection: Simple and instant coupling to the lamp without plug connection.Broad compatibility: Suitable for many of the most common compact OLight torches and lamps.Integrated status LED: Clearly indicates charging status (Red: charging active / Green: charging complete).Universal USB-A connector: Usable with any standard USB power supply, any power bank or computer.Robust and durable: Designed for daily, professional use and easy transport.Compatibility and professional benefitThe correct assignment of the charging cable is crucial for maintaining professional equipment. The MCC-1A charging cable with a charging current of 1A is intended for use with many compact and medium-sized OLight lamps. It ensures efficient and gentle charging of the battery and is compatible with, among others, the following widely used models:Baton 3S1R Baton II, S2R Baton IIPerun MiniWarrior Mini, Warrior Mini 2Obulb series, Oclip seriesPlease note that this cable is not intended for high-performance models such as the Marauder series or models that require the faster MCC3 charging cable (2A).Simple and safe charging functionThe magnetic charging system from OLight has been developed for maximum user-friendliness and durability. The magnetic head is simply held close to the charging surface on the lamp's end cap and couples automatically. This avoids wear and tear of mechanical plug connectors or rubber covers and protects the lamp's waterproofness. The LED integrated in the charging head gives a clear and unambiguous feedback on the status of the charging process.An indispensable accessoryFor professional users who have to rely on their equipment, a second charging cable is a sensible investment. An MCC-1A in the vehicle or laptop bag ensures that your OLight torches are quickly ready for the next shift or job even after a long day of use. The compact design and the robust cable make it the ideal companion. Features  ModelOLight MCC-1A Product typeMagnetic USB charging cable InputUSB-A OutputMagnetic charging connection Max. charging current (A)1 Input voltage (V)5 Cable length (m)approx. 1.2 Weight (g)approx. 34 ColourBlack Compatibility (excerpt)Obulb series, Olink, PL-Mini 2, Baldr Mini, Baldr S  FAQs about the OLight MCC-1A charging cableHow do I know if my OLight torch is compatible with this cable?Check the product description or the original packaging of your OLight torch. As a rule, the compatible cable type (e.g. MCC-1A or MCC3) is specified there. In general, this 1A cable is intended for most smaller to medium-sized torch models.What is the difference between the MCC-1A and the MCC3 charging cable?The main difference is the maximum charging current. The MCC-1A charges at up to 1 amp, while the MCC3 charges at up to 2 amps. The MCC3 is designed for torches with larger batteries and higher power requirements. Using the wrong cable can lead to significantly longer charging times.Can I use this cable with any USB power supply?Yes, you can use any standard USB-A power supply (e.g. from a smartphone), a car charger, a power bank or the USB port of a computer, as long as it can provide a stable power output of at least 1A.Why is a magnetic charging cable advantageous in professional use?The magnetic system enables quick, 'blind' coupling even in the dark. There are no mechanical parts that can wear out or break, and the charging socket on the torch itself always remains sealed and waterproof, which increases reliability for outdoor use.

The Olight i3E EOS is the classic among ultra-compact torches. In contrast to the previously discussed i1R 2 Pro (which has a fixed battery), this model is operated with a perfectly normal AAA battery (Micro). It is renowned for its simplicity: there is only a single lighting mode. Due to its very attractive price and robust construction, it is one of the world's most popular backup lights, which you simply forget on your key ring until you need it.Highlights at a glanceAAA battery operation: Operated with a single standard AAA battery (or a NiMH cell like Eneloop). This means: simply replace the empty battery, no need to wait for charging.Compact and Light: With a length of just 60.5 mm and a weight of approx. 19 grams (including battery), it is virtually unnoticeable on your key ring or in your trouser pocket.Simplest operation: Features only a single lighting mode ("Mono Mode"). Tighten the head = light on, loosen the head = light off. No complicated click combinations.TIR optics: Uses a high-quality PMMA TIR lens (Total Internal Reflection) which generates a soft, balanced beam ideal for close range (path at your feet, keyhole).Good performance: Delivers 90 lumens (for the standard colours black, blue, red etc.) and even 120 lumens for the silver version, which is impressive for the size.Robustness: The housing is made from aircraft aluminium alloy (or copper/brass for special editions) and is IPX8 waterproof (submersible to 2 metres).Comparison: i3E EOS vs. i1R 2 ProMany users are undecided between these two little Olights. Here’s the decision aid:Choose the i3E EOS (AAA) if: You want a lamp for emergencies that will still work instantly after 5 years in a drawer (with a lithium battery), or if you’d prefer to swap batteries quickly rather than recharge. It is also more affordable.Choose the i1R 2 Pro (USB-C) if: You use the lamp daily. Constantly buying AAA batteries would get annoying. The i1R 2 Pro is also brighter (180 lm) and even shorter.Features ModelOlight i3E EOS (battery version) ApplicationMinimalist EDC, backup light, gift Light output (lumens)**90 lumens** (Only one mode: On/Off) Beam rangeapprox. 44 metres (Wide beam thanks to TIR optics) Power supply1x AAA battery (alkaline) or 1x AAA rechargeable (NiMH) Runtimeapprox. 45 min (alkaline) / approx. 70 min (Eneloop NiMH rechargeable) OperationRotary switch (Twisty): Tighten head = On / Loosen = Off Dimensions (L x Ø in mm)60.5 x 14 (Only minimally larger than the battery itself) MaterialA6061-T6 aluminium (hard anodised) Water resistanceIPX8 (Completely waterproof to 2m) Weight (g)approx. 19.4 (including battery)  FAQs about the Olight i3E EOSCan I use 10440 lithium-ion cells?No, not officially. A 10440 cell is the size of an AAA battery, but provides 3.7 volts (instead of 1.5V). If you insert one, the torch becomes extremely bright (approx. 300+ lumens), but will get hot within seconds and the LED can burn out. The electronics are not designed for this. Stick to alkaline (1.5V) or NiMH cells (1.2V).Why does the silver version have more lumens?The silver i3E is not painted/anodised like the black or colourful versions, which has a minimal impact on heat dissipation, but the main reason is often a different LED driver for this specific edition. It provides 120 lumens instead of 90, but the runtime is slightly lower (approx. 35 min vs. 45 min).Is a clip included?No. The i3E EOS has no pocket clip. It only features a small ring at the end to attach it to a key ring. It is designed purely as a keychain light.

The Olight i1R 2 Pro is an extremely compact, rechargeable LED torch specially designed for the key ring (EDC – Everyday Carry). It is the upgrade of the popular i1R 2 EOS and is distinguished primarily by the modern USB-C charging port and increased battery capacity. Despite its tiny size (barely larger than an AA battery), it delivers an impressive 180 lumens. The black anodised aluminium housing is robust and scratch-resistant.Highlights at a glanceHidden USB-C charging port: No need to disassemble the torch for charging. Simply unscrew the head to reveal the USB-C port, which is protected from dust and water when closed.Impressive performance: Delivers up to 180 lumens in high mode (range approx. 48 metres) and 5 lumens in low mode for reading maps or searching for keyholes – despite the tiny size.Simple rotary operation: No button that could be pressed accidentally in your pocket. Purely controlled by turning the head (tighten = on/bright, loosen = off).Quick charging: The fixed lithium-ion battery (130 mAh) is fully charged in about 100 minutes via a standard USB-C cable (included).Extremely lightweight: At only 22 grams it is virtually unnoticeable on your key ring and won't bother you in your car’s ignition.Operation & ChargingThe i1R 2 Pro uses an intelligent mechanism:Switch on (Low): Turn the head slightly clockwise.Switch on (High): Turn the head further until it stops.Switch off: Turn the head back anti-clockwise.Charging: Unscrew the head far anti-clockwise (don't worry, it won't come off!). The head slides upwards to expose the USB-C port. A small LED lights up Red (charging) or Green (Full).Features ModelOlight i1R 2 Pro (key chain torch) ApplicationEDC (Every Day Carry), Emergency light, Key light Light output (lumens)Mode 1: **180 lm** (High) / Mode 2: **5 lm** (Low) RangeMax. 48 metres (surprisingly long for the size) Power supplyIntegrated 130 mAh 3.7V Li-Ion battery (type 10180) Charging port**USB-C** (Hidden in the centre – unscrew head for access) OperationRotary switch (Twisty): Turn slightly = Low, Tighten = High Dimensions (L x Ø in mm)51.3 x 16.2 (Barely larger than an AA battery) MaterialAluminium alloy (aerospace quality), hard anodised Water resistanceIPX8 (continuous submersion up to 2 metres possible) Weight (g)approx. 22 (including battery and key ring)  FAQs about the Olight i1R 2 ProCan I replace the battery?No. The 130mAh lithium-ion battery is permanently integrated into the housing to ensure waterproofness (IPX8) and extremely compact dimensions. As the torch is intended for short use, the battery will last many years under normal use.What is the difference to the old i1R 2 (without Pro)?The most important upgrade is the charging port.Old (i1R 2 EOS): Micro-USB (the head had to be completely removed).New (i1R 2 Pro): USB-C (the head stays attached). The Pro also has slightly more luminosity (180 vs. 150 lumens) and a larger battery (130mAh vs. 70mAh).Does the torch turn on by itself in your pocket?That is very unlikely. The rotary mechanism has a pleasant resistance. Since you have to tighten the head to switch on the torch, this almost never happens accidentally (unlike lamps with side switches).

The Olight Javelot Pro 2 is the flagship among the so-called "Throwers" (long-range flashlights) by Olight. Unlike conventional torches that broadly illuminate the area in front of your feet, the Javelot Pro 2 focuses the light extremely intensely. The result is a concentrated light beam that cuts through the darkness like a "lightsaber" and achieves a range of over 1 kilometre. It is primarily designed for hunting, search and rescue operations (SAR) as well as for security services that need to identify objects at long distances.Highlights at a glanceGigantic range: Thanks to a high-performance LED and a deep reflector, it reaches a range of up to 1050 metres. Ideal for illuminating objects at extremely long distances.Enormous brightness: Delivers a maximum of 2500 lumens. That's a lot for a pure thrower, as long-distance torches often had fewer lumens to focus the beam.Dual-switch system: Features a tail switch (for tactical access: instant turbo or low) and a side switch (for comfortable mode selection in normal use).Smart indicators: Around the side switch, there are LED indicators, which show you the battery level on one side and the currently selected brightness level on the other side.Integrated battery pack: The torch is operated with a special battery pack handle (two integrated 21700 batteries with a total capacity of 10000 mAh), which enables very long runtime and is charged via magnetic charging cable.Mountable: With optional accessories (magnetic mount, remote switch) the torch can be mounted on equipment or optics, making it especially interesting for hunters.Thrower vs. FlooderIt is important to understand that this is not a torch for a leisurely walk or for reading in a tent. The light cone (hotspot) is very narrow and bright.Flooder: Wide beam, short distance (e.g. Olight Seeker series).Thrower (Javelot): Narrow beam, extreme distance. Features ModelOlight Javelot Pro 2 (ultra long-range) ApplicationHunting, search & rescue (SAR), police, asset protection Luminous flux (lumens)Max. 2,500 lumens (focus is on range, not flood light) Range1,050 metres (extremely focused spot) Power supplyIntegrated battery pack handle (2x 21700 Li-Ion / 3.6V / 10000 mAh) RuntimeUp to 12 days (in low mode) / approx. 5 min full throttle (then regulation) OperationDual switch: tail switch (tactical/turbo) & side switch (normal) IndicatorLED indicators on the side switch for brightness & battery status Dimensions (L x Ø head in mm)259 x 63 (A long "baton" with a very large head) Accessory compatibilityFits special weapon mounts, remote switch connectable Weight (g)approx. 423 (including battery pack)  FAQs about the Olight Javelot Pro 2Can I insert normal 21700 batteries?No. The Javelot Pro 2 does not use an open battery compartment; the entire handle is the battery ("Battery Pack"). You can unscrew and replace the handle, but you cannot replace the individual cells inside. If the battery is empty, you need to charge the whole handle or have a spare handle with you.What is the difference to the Javelot Turbo?The Javelot Pro 2 is the more modern model.Brightness: Pro 2 has 2500 lumens (Turbo has 1300 lumens).Range: Both are similar (Pro 2: 1050m / Turbo: 1300m - the Turbo focuses a bit more with fewer lumens).Operation: The Pro 2 has the convenient side switch with LED indicator which the Turbo does not offer.Does the torch get hot?Yes, in turbo mode (2500 lumens) the head develops heat quickly. The torch therefore regulates itself down automatically after about 5 minutes (to 1000 lumens) to protect the LED and electronics. This is completely normal with high-performance torches.Is a case included?Yes, the Javelot Pro 2 is supplied in a very robust, water- and dustproof carrying case made of plastic, in which the torch, charging cable, and holster can be stored.

The Olight Prowess is an innovative torch that follows a completely new concept: it is a bi-directional lamp. This means it does not only shine forwards like a conventional torch, but can also shine "backwards" to act as a 360-degree lantern. With a maximum output of 5000 lumens and a unique operating concept, it is aimed at users looking for a powerful torch for outdoors and, at the same time, for atmospheric room or tent lighting.Highlights at a glanceBi-directional lighting: The Prowess has LEDs at the front (for a focussed, long-distance beam) and special LEDs at the rear (for soft, warm white 360° light as a lantern).Enormous output: In torch mode, it briefly delivers up to 5000 lumens, which is extremely bright for a lamp of this size. The beam reaches up to 245 metres.Warm white lantern light: The reverse mode (Lantern Mode) uses warm white LEDs which are steplessly dimmable. This creates a cosy atmosphere when camping or as emergency lighting at home.Dual charging options: The lamp can either be charged in the conventional way using the magnetic MCC3 charging cable on the base of the lamp, or using the detachable base supplied, which has a USB-C connection.Innovative operating concept: A novel toggle switch/rotary dial enables seamless switching between the front spot light and the rear lantern light as well as stepless dimming.Versatile mounting: The delivery includes a mount, so the lamp can be fixed to the wall, mounted on a tripod, or used as a standing table lamp.One lamp, two worldsThe Prowess solves the problem that when camping you often need two devices: a torch for walking and a lantern for the table. The Prowess combines both in a very futuristic, grippy design. Especially the "Reverse Light" (rear light) is unique: The light does not come out at the front, but is emitted through slits in the body, which creates glare-free ambient lighting. Features ModelOlight Prowess (Hybrid lamp) ApplicationCamping lantern, emergency lighting at home, searchlight Functionality**Bi-directional:** Switchable between front light (spot) and rear light (lantern) Light output (lumens)Front: Max. **5,000 lm** (Turbo) / Rear: Max. **800 lm** (Lantern) Light colourFront: Cool white (5500K - 6000K) / Rear: **Warm white** (2800K - 3200K) Power supplyIntegrated 21700 Li-Ion battery (5000 mAh) Charging systemMagnetic (MCC3) OR via USB-C (with detachable base/holster) OperationToggle switch (direction selection) + rotary dial (brightness) Dimensions (L x Ø in mm)143 x 49 (Solid head for heat dissipation) AccessoriesIncl. wall bracket & table station (lamp clicks in) Weight (g)approx. 269 (Feels very high-quality and solid)  FAQs about the Olight ProwessHow do I switch between front and rear?This is done via the large toggle switch on the top.Switch up: Activates the front light (torch).Switch down: Activates the rear light (lantern).Rotate: Stepless brightness adjustment.Press: On/off.Can I use regular 21700 batteries?No. As with most high-end Olight lamps, it uses a modified 21700 battery (both poles at the front), which is necessary for magnetic charging and high currents. Standard batteries will not work.Is the lamp magnetic?Yes, the end cap is magnetic. You can therefore fix the Prowess (upside down) to bonnets or steel beams to use it as a work light. The magnet also secures the lamp in the supplied charging tray.What is the advantage of the included base?The base acts as a "docking station". You can mount the base on the wall or place it on the table. The base is connected via USB-C. When you place the lamp in the base, it charges. This is more practical than looking for the magnetic cable every time.

The Olight Strip is a 5 metre long RGB LED strip, specially developed for atmospheric ambient lighting and conveniently controlled via smartphone app. Since it is powered via a simple USB connection, it is extremely flexible in use – from gaming setups to tents.Highlights at a glanceApp control (Bluetooth): Via the Olight App, the strip can be conveniently controlled. You can choose from 66 preset scenes (e.g. "Party mode", "Reading", "Night") or create your own colour effects.Music synchronisation: Thanks to an integrated microphone (or via the phone), the strip can pulse in time to the music. Ideal for parties or as dynamic background lighting for gaming.USB-powered (5V): The strip does not require a bulky power supply unit. It is simply connected to a USB-A port (e.g. power bank, PC, TV or mobile phone charger). With a consumption of only 5 watts, it is very economical.Smart timer function: In the app, you can set countdowns or schedules so that the light wakes you up in the morning or switches itself off in the evening.Simple installation: There is a strong adhesive strip (3M) on the back, which can be used to fix the Ostrip to walls, under cabinets or behind the TV. Mounting clips are also included.Flexible & shortenable: The strip is flexible and can be placed around corners. It can theoretically be shortened at marked points (Caution: cut parts no longer work without their own controller).The perfect "Mood Light"The Ostrip is not a replacement for a bright ceiling lamp, but a mood light. With around 150 lumens (RGB), it is not extremely bright, but it is glare-free and perfect for setting colourful accents. Since it can be powered by a power bank, it is also a hot tip for camping fans who want to illuminate their tent or pavilion. Features ModelOlight Ostrip (Smart LED Strip) ApplicationTV backlight, gaming setup, shelf lighting, party decor Light output (lumens)approx. 150 lumens (Purely decorative light, not for room illumination!) Length5 metres (shortenable at marked positions) + 1.5m cable Power supplyUSB-A plug (5V / 1A) - Works with power bank, TV-USB or PC ControlOlight App (Bluetooth) or cable controller (3 buttons) FunctionsMusic sync (integrated microphone), scene modes, timer, dimmable LED type5050 RGB LEDs (Coloured light) MountingSelf-adhesive (3M backing) or supplied holding clips Special featuresOlight’s smart home entry, reacts to ambient sound Weight (g)approx. 197 (complete set)  FAQs about the Olight OstripDo I absolutely need the app?No, not absolutely. There is a small controller with 3 buttons on the cable. This allows you to switch the strip on/off, change the brightness and cycle through some basic modes. For full functionality (precise colour selection, timer, music scenes), however, the app is necessary.Can I extend the strip?No. The Ostrip is a closed system. You cannot simply plug a second strip onto the end, as the power supply via USB (5 watts) would not be sufficient for this.Is it bright enough as an under-cabinet kitchen light?Rather not as a work light. With 150 lumens over 5 metres, the light is more decorative ("dim light"). For chopping vegetables you need much more brightness and especially pure white light. The Ostrip is more for colourful accents (RGB).Does it work with Alexa or Google Home?In the basic version usually no. The Ostrip connects directly to the phone via Bluetooth. It does not have a Wi-Fi module. To make it theoretically smart, you would need a specific Olight gateway (Olight Hub), but “out of the box” it is a pure Bluetooth control.

This solar extension cable set (1 metre, 4mm²) is the professional solution for safely bridging the distance between solar modules and inverters or charge controllers. The set usually consists of two cables: one red cable for the positive pole (+) and one black cable for the negative pole (-). This colour coding effectively prevents dangerous polarity reversal errors during installation.The cables are already pre-assembled with MC4-compatible plugs and sockets on both sides (“Plug & Play”). You do not need to purchase any crimping tools – simply plug them together and you are done. The high-quality insulation has been specially developed for decades of outdoor use: it is extremely UV-resistant, weatherproof and withstands large temperature fluctuations.Highlights at a glancePlug & Play: Pre-assembled with MC4-compatible plug connectors (plug + socket) for immediate use.Colour coding: Set consisting of Red (+) and Black (-) ensures error-free installation and fast assignment of the poles.Weatherproof (IP67): The connectors are dustproof and protected against brief submersion—ideal for rain and snow.UV- & ozone-resistant: The tough outer sheath made from cross-linked polyolefin withstands harsh sunlight for years without becoming brittle.High-quality conductor: The tinned copper cable (4mm²) ensures minimal resistance and the lowest power loss over this short distance.Certified safety: Meets common standards (e.g. TÜV, EN 50618) for photovoltaic installations up to 1000V/1500V DC.Areas of applicationThe 1 metre extension is ideal for short bridging:Balcony power stations: If the cables on the solar module are just too short to reach the micro inverter.Series connection (strings): To connect two modules installed next to or above each other.Camping & boat: For flexible setup of mobile solar cases or panels in the sun while the vehicle remains in the shade.Off-grid systems: Connection from the roof to the charge controller for short routes (e.g. garden shed).Installation & safety instructionsAudible click: When plugging together, ensure that the plugs engage with a distinct “click”. Only then is the connection sealed and electrically safe.Do not disconnect under load: Never separate the plug connections while current is flowing (i.e. when the sun is shining and the inverter is operating). A dangerous arc may form. Cover the modules beforehand or switch off the inverter.Bending radius: Do not sharply bend the cables, especially not directly behind the connector housing, to avoid compromising the seal.Mounting: Do not leave the cables loose in the wind. Secure them to the module frame or substructure with UV-resistant cable ties to avoid chafing. Properties Product nameSolar extension cable set (1 m) Cable length**1.0 metre** (per cable) Cable cross-section**4.0 mm²** Rated voltage**1000 V / 1500 V DC** Connector type**MC4-compatible** Conductor materialCopper (tinned) Degree of protection (connected)**IP67 / IP68** (waterproof) Temperature range-40°C to +90°C Colours in the set1x Red (+), 1x Black (-) Standards / certificatesEN 50618 (H1Z2Z2-K)  FAQs about the 1m solar extension cableIs a 4mm² cross-section sufficient or do I need 6mm²?For a length of 1 metre and standard applications, 4mm² is perfectly adequate. Over such a short distance, the voltage drop is negligibly low. 4mm² cables can easily carry currents up to approx. 40–50 amps. Standard solar modules typically supply only 10 to 14 amps. 6mm² cables are only worthwhile for very long distances (e.g. >20 metres) or extremely high-performance systems.Can I also use the red cable for the negative pole?Technically yes, but it is dangerous. The inside of the cable (copper) and the connectors are identical. The colour of the insulation is only for marking. If you use “Red” for “minus”, the system will work, but there is an extremely high risk of confusion during later maintenance work or expansion, which can destroy the inverter.Are the cables suitable for underground installation?Conditionally. Although the insulation is very robust, standard solar cables are not explicitly designed for direct laying in the ground without a protective conduit (hazards from rodents, standing water, stones). Always use an empty conduit or protective tube in the ground.

This solar extension cable set (2 metres, 4mm²) is the ideal solution for short bridging in your photovoltaic system. When installing balcony power plants or connecting solar modules in series, it is often just a few metres missing to lay the cables without voltage. With this 2-metre set you can solve the problem professionally and safely.The set consists of two high-quality, double insulated solar cables: a red cable for the plus pole (+) and a black cable for the minus pole (-). Both ends are already pre-fitted with MC4-compatible plugs and sockets ready-made ("Plug & Play"). The 4mm² cross-section made of tinned copper ensures absolutely loss-free power transmission over this short distance. The sheathing is extremely resistant to UV radiation, heat, cold and moisture.Highlights at a glancePerfect quick solution: 2 metres length is ideal for connecting modules with each other (string) or for slightly extending the route to the inverter.Plug & Play: No pliers required – the cables are pre-assembled with MC4-compatible plugs and sockets on both sides.Safety colour code: The combination of Red (+) and Black (-) prevents dangerous polarity reversal and makes maintenance easier.Loss-free: At only 2 metres length, the voltage drop with 4mm² cross-section is virtually unmeasurable (almost 0%).Weatherproof (IP67): The connections are dustproof and water-resistant, the insulation withstands extreme temperatures (-40°C to +90°C).Durable: Halogen-free, UV- and ozone-resistant sheath for a service life of over 25 years in outdoor areas.Areas of applicationThe 2-metre extension is a classic "problem solver" cable:Series connection (strings): To connect two solar modules that are not directly adjacent (e.g. due to a skylight or chimney in between).Balcony power stations: If the factory cables on the module are too short to reach the micro inverter conveniently behind the frame.Camping & boat: Flexible connector for portable solar suitcases or panels on the motorhome roof.Charge controller connection: Connection from the roof penetration to the nearby charge controller indoors.Installation & safety instructionsPlug connection: Always press plug and socket together as far as they will go until a clearly audible "click" is heard. This is the only way to guarantee tightness (IP67).Bend radius: Even with short cables: do not bend the cable directly at the plug housing. Leave the cable about 3-5 cm straight run distance.Fastening: Do not allow the cable to flap loosely in the wind ("knocking" on the roof). Attach it with UV-resistant cable ties to the module frame or substructure.Disconnect: Never disconnect the plugs under load (in operation). Always switch off the consumer/inverter first. Features Product nameSolar extension cable set (2 m) Cable length**2.0 metres** (per cable) Cable cross-section**4.0 mm²** Cable standard**H1Z2Z2-K** (PV1-F) Rated voltage**1500 V DC** (max.) Conductor materialTinned copper (class 5) Connectors**MC4-compatible** (Male + Female) Protection class**IP68** (waterproof) Temperature range-40°C to +90°C CertificatesTÜV / CE / RoHS  FAQs on the 2m solar extension cableDo I absolutely need 4mm² for 2 metres length or is thinner ok?4mm² is the standard and ideal. Thinner cables (e.g. 2.5mm²) are less mechanically robust and the plugs often fit less well. 4mm² offers the optimum compromise of flexibility and conductivity. A 6mm² cable would be unnecessarily expensive and stiff for this short length.Do the plugs fit my Hoymiles/Deye inverter?Yes. The micro-inverters from Hoymiles, Deye, NEP etc. have standardised MC4 plugs (or compatible BC01/TS4). These extension cables fit perfectly in between mechanically.Can I plug two of these cables together to get 4 metres?Yes, easily. Thanks to the plug-socket principle, you can plug several cables together ("daisy-chaining"). Just note that every connection point can be a potential source of moisture – a continuous 4m or 5m cable would be more elegant, but technically 2x 2m is also possible.

The solar extension cable set (3 metres, 4mm²) is the ideal solution for short distances within a photovoltaic installation. If you need to bridge short distances between your solar modules or want to connect to a nearby inverter or charge controller – for example, on a balcony, a garage roof or in the camping area – this set offers a secure and virtually loss-free connection.The set includes two high-quality, double-insulated solar cables: one red cable for the positive terminal (+) and one black cable for the negative terminal (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the short length of 3 metres and the solid cross-section of 4mm², this set is ideally suited for almost all common PV applications (balcony systems, off-grid systems, roof systems).Highlights at a glanceOptimal short-distance solution: With 3 metres in length, ideal for connecting modules in a string or for direct connection of microinverters.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so that no special tools are required for crimping.Secure identification: The colour coding in red (+) and black (-) makes installation easier and effectively prevents incorrect polarity.Weatherproof & durable: The special jacket made from cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection rating IP67: When plugged in, the connectors are absolutely dustproof and protected against splashing water and rain.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 3-metre extension is designed for a wide range of application scenarios:Balcony systemsPerfect for bridging the distance between the solar modules and the microinverter mounted directly behind or below them.String cablingBridging gaps between rows of modules on pitched roofs or flat roof elevations.Motorhomes & boatsConnecting solar modules to the charge controller in compact spaces where long cable runs are not required.Assembly & safety instructionsMinimal voltage dropWith a length of only 3 metres, the voltage drop is negligibly small. For both 12V/24V off-grid systems and high-voltage systems, this cross-section is technically perfectly dimensioned for this length.Strain reliefSecure the cables with UV-resistant cable ties to the mounting frame. Avoid mechanical stress on the plug-in connections and the module junction boxes.Correct latchingWhen connecting, ensure that the MC4 connectors audibly snap into place. This is the only way the connection will remain permanently watertight and safe from arcing. Features ModelSolar extension cable set (3m) Conductor cross-section**4.0 mm²** Cable length**3.0 metres** (per colour) Rated voltageUp to 1000V / 1500V DC Plug type**MC4 compatible** (IP67) Temperature range-40°C to +90°C Insulation materialCross-linked polyolefin (LSZH) Protection rating**IP67** (plugged in) Special featureUV- & ozone-resistant, acid-resistant FAQs about the solar extension cable 3mIs 4mm² enough for my 800W balcony system?Yes, absolutely. With 3 metres and a typical current of about 10–13 amperes, the resistance is so low that there are practically no measurable losses. 4mm² is standard here and is fully sufficient.Can I also leave these cables outdoors?Yes, that's what they're made for. The cables are certified according to standard PV norms. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.Do the connectors fit modules from Trina, Jinko or JA Solar?Yes. These manufacturers use MC4 or compatible systems (like EVO2) as standard. The connectors on this extension cable fit perfectly, both mechanically and electrically, to these module connectors.

The solar extension cable set (5 metres, 4mm²) is the ideal solution for moderate distances within a photovoltaic installation. If you need to bridge distances between your solar modules or want to connect to an inverter or charge controller that is nearby – for example on a balcony, a garage roof or in the garden – this set provides a safe and efficient connection.The set includes two high-quality, double-insulated solar cables: one red cable for the positive terminal (+) and one black cable for the negative terminal (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the compact length of 5 metres and the solid cross-section of 4mm², this set is technically perfectly suited for almost all common PV applications (balcony power plants, off-grid systems, roof systems).Highlights at a glanceOptimum range: With a length of 5 metres, ideal for connecting modules in one string or connecting microinverters at moderate distances.Plug & play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special tools are required for crimping.Safe identification: The colour coding in red (+) and black (-) makes installation easier and effectively prevents incorrect polarity.Weatherproof & durable: The special cross-linked polyolefin jacket is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection class: The plugged connections are absolutely dust-tight and protected against splashing water and rain.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 5-metre extension is designed for a wide range of use scenarios:Balcony power plantsPerfect for bridging the distance between the solar modules and the inverter when it is mounted slightly offset.String wiringBridging gaps between module arrays on pitched roofs or flat roof elevations.Motorhomes & campingConnecting solar modules to the charge controller so the vehicle can be parked in the shade while the panels are in the sun.Installation & safety instructionsMinimal voltage dropAt 5 metres in length, the voltage drop is negligibly low. For both 12V/24V off-grid systems and high-voltage systems, this cross-section at this length is technically optimally dimensioned.Strain reliefSecure the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical strain on the plug connections and the module connection boxes.Correct latchingWhen plugging them together, make sure the MC4 connectors audibly engage. Only then will the connection be permanently waterproof and safe from arcs. Features ModelSolar extension cable set (5m) Conductor cross-section**4.0 mm²** Cable length**5.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +90°C StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureFlame retardant & short-circuit proof  FAQs about the solar extension cable 5mIs 4mm² sufficient for my 800W balcony power plant?Yes, absolutely. With a length of 5 metres and a typical current of approx. 10-13 amps there are practically no measurable power losses. 4mm² is the industry standard here and perfectly sufficient.Can I leave these cables outdoors?Yes, that is what they are designed for. The cables are certified to common PV standards. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.Do the connectors fit modules from all well-known brands?Yes. These cables use MC4-compatible standard connectors. They fit perfectly mechanically and electrically to the connections of manufacturers such as Trina, Jinko, JA Solar or Canadian Solar.

The solar extension cable set (8 metres, 4mm²) is the ideal solution for moderate distances within a photovoltaic installation. If you need to bridge the gap between your solar modules or connect to an inverter or charge controller nearby – for example on a balcony, garage roof or in the garden – this set offers a secure and efficient connection.The set includes two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the compact cable length of 8 metres and robust cross section of 4mm², this set is technically an excellent choice for almost all common PV applications (balcony systems, off-grid systems, roof installations).Highlights at a glanceOptimum reach: With a length of 8 metres, ideal for connecting modules in a string or for connecting microinverters at moderate distances.Plug & Play installation: The cables are pre-assembled at both ends with MC4-compatible connectors, so no special crimping tool is required.Safe identification: The colour coding in red (+) and black (-) makes installation easier and effectively prevents polarity errors.Weatherproof & durable: The special cross-linked polyolefin sheath is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 rating: When plugged in, the connectors are completely dustproof and protected against splashing water and rain.High-quality conductor: Tinned electrolytic copper provides excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 8-metre extension is designed for a variety of scenarios:Balcony PV systemsPerfect for bridging the distance between solar panels and the inverter when the inverter is mounted slightly offset.String cablingBridging gaps between module arrays on pitched roofs or flat roof mounts.Motorhomes & campingConnecting solar modules to the charge controller so the vehicle can be parked in the shade while the panels are in the sun.Installation & safety informationMinimal voltage dropAt 8 metres in length, the voltage drop is negligibly low. For both 12V/24V standalone systems and high voltage systems, this cross section at this length is technically optimal.Strain reliefSecure the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical strain on the connectors and module junction boxes.Correct latchingWhen plugging together, make sure the MC4 connectors click audibly into place. Only then will the connection remain permanently watertight and safe against arcing. Features ModelSolar extension cable set (8m) Conductor cross-section**4.0 mm²** Cable length**8.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range-40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureHalogen-free & UV-resistant  FAQs about the Solar Extension Cable 8mIs 4mm² sufficient for my 800W balcony PV system?Yes, absolutely. At 8 metres length and a typical current of around 10–13 amperes, there are practically no measurable power losses. 4mm² is the industry standard for this and is perfectly sufficient.Can I leave these cables outdoors?Yes, that’s what they’re designed for. The cables are certified to current PV standards. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.Do the connectors fit modules from all common manufacturers?Yes. These cables use MC4-compatible standard connectors. They fit mechanically and electrically perfectly to the connections of manufacturers such as Trina, Jinko, JA Solar or Canadian Solar.

This solar extension cable set (10 metres, 4mm²) offers you maximum freedom when positioning your solar modules. With a length of 10 metres, you can easily bridge longer distances – for example, from the garden shed to the storage in the basement or from the sunny installation site in the garden to the feed-in socket at the house.The set consists of two high-quality, double-insulated solar cables (1x red for positive, 1x black for negative), which are already pre-assembled with MC4-compatible connectors. Despite the length of 10 metres, the 4mm² cross-section made of tinned copper ensures low-loss power transmission. The sheathing is extremely weather-resistant, UV-stable and designed for permanent outdoor use in heat, cold and moisture.Highlights at a glanceLong range: 10 metre cable length enables flexible location choice of the modules far from the inverter.Plug & Play: Pre-assembled on both sides with MC4-compatible plugs and sockets – no tools required.Safe installation: The set of Red (+) and Black (-) prevents dangerous polarity reversal mistakes when cabling.Low loss: The high-quality copper conductor (4mm²) keeps the voltage drop low even at 10 metres distance (ideal for typical module currents up to 20A).Extremely robust: The special insulation is resistant to UV radiation, ozone, acids and alkalis, and temperature resistant from -40°C to +90°C.Waterproof (IP67): The connected joints are dustproof and protected against temporary submersion.Areas of applicationThe 10-metre extension is the problem solver for long runs:Open area & garden installation: If the modules are positioned in the sunny part of the garden but the inverter or feed-in point is located at the house.Camping & mobile solar: Enables the camper van to park in the shade while the mobile solar module is 10 metres away in full sun.Roof-to-basement connection: For routing the DC cables from the roof through empty ducts to the charge controller or inverter in the utility room.Building shading: To place modules in locations that are not hit by the shadow of your own house in the morning or evening.Installation & safety instructionsCable laying: At 10 metres length, the cables should not be left loose. Secure them with cable ties or lay them in a protective pipe/cable duct to protect against mechanical damage (lawnmower, animal bites) and tripping hazards.Avoid coiling: If you do not need the full 10 metres, do not coil the excess cable tightly (induction effect/heat). Lay it out rather in wide loops ("meandering").Check connection: When plugging together, listen for the audible "click" of the connectors to prevent arcing and moisture ingress.Disconnecting under load: Never pull apart the connectors under load (when the sun is shining). Turn off the inverter or cover the modules first. Features Product nameSolar extension cable set (10 m) Cable length**10.0 metres** (per cable) Cable cross-section**4.0 mm²** Rated voltage**1500 V DC** (max.) Rated current (max.)approx. **30 A** (depending on installation) Plug type**MC4-compatible** (Male/Female) Conductor materialTinned copper strand Protection class**IP68** (waterproof when plugged in) Temperature range**-40°C to +90°C** Standard complianceTÜV / CE / EN 50618  FAQs on the 10m solar extension cableIs 4mm² sufficient for 10 metres or is there too much loss?For normal applications (balcony power station/camping), 4mm² is absolutely sufficient. For a typical solar module (approx. 10-13 amps), the voltage drop over 10 metres (go and return = 20m cable length) is very low (mostly under 1-2%). An upgrade to 6mm² is only necessary for very high currents (e.g. parallel connection of several modules before the cable) or for even longer lengths.Can I shorten the cable if 10 metres is too long?Yes, but with effort. You can cut the cable but will lose the moulded/crimped connector on one side. You will then need special crimping pliers for solar cable and new MC4 connectors to re-establish a connection. Simple terminal block connections or soldering are not recommended for outdoor high current solar applications.May I bury the cable directly in the ground?No, better not without protection. Although the insulation is very robust, standard solar cables are not specified for permanent burial (danger from stones, moisture, rodents). For the garden run, use a cost-effective PE empty pipe or a flexible cable protection hose.

With this solar extension cable set (12 metres, 4mm²) you can also safely and weatherproof bridge larger distances between your solar modules and the inverter or charge controller. The length of 12 metres offers you maximum flexibility, for example to optimally align modules to the sun on a garden shed, garage or far away in the garden, while the technology remains protected in the house.The set includes two double-insulated solar cables (1x red for plus, 1x black for minus), already assembled with MC4-compatible plugs and sockets. Despite the considerable length, the high-quality conductor cross-section of 4mm² made of tinned copper ensures reliable power transmission. The sheathing is specially designed for permanent outdoor use and withstands UV radiation, heat, cold and moisture for many years.Highlights at a glanceExtra range: 12 metres of cable length enable flexible installations even in difficult structural conditions or long routes through the garden.Ready for immediate use: Pre-assembled on both sides with standard MC4-compatible connectors (Plug & Play) – no crimping required.Safety colour code: The set of red (+) and black (-) virtually excludes confusion when connecting and protects your expensive electronics.High-quality material: Tinned copper (4mm²) provides good corrosion protection and low line losses.Weatherproof (IP67): The connectors are dust-tight and waterproof when plugged in, ideal for rain and snow.Durable: The special insulation is resistant to UV radiation, ozone, acids and alkalis and is temperature-resistant from -40°C to +90°C.Areas of applicationThe 12 metre extension solves installation problems for long distances:Garden shed & garage: If the modules are on the outbuilding but the inverter or storage is accommodated in the main house.Shading optimisation: Allows the placement of the modules far from shade-providing trees or buildings.Façade installation: For neat routing of the cables from the façade to the plant room or cellar.String extension: To electrically connect module fields that are structurally separated (e.g. on two different sides of a roof).Installation & safety instructionsNote voltage drop: With 12 metres (24m current path there and back), a physically caused resistance arises. For standard modules (up to around 10–15A), 4mm² is perfectly sufficient. However, if you are planning high-performance strings with very high currents (>20A), you should check the voltage drop.Strain relief: Due to the weight of 12m cable, the connectors on the module should not be under tension. Fix the cable to the frame with cable ties.Mechanical protection: With this length, the cable often runs over edges or through the garden. Be sure to use protective conduit (duct) at abrasive points or for underground installation.Connection: Firmly press the connectors together until a clear "click" is heard. A loose connection can get hot. Properties Product nameSolar extension cable set (12 m) Cable length**12.0 metres** (per cable) Cable cross-section**4.0 mm²** Rated voltage**1500 V DC** Max. operating currentup to **30 A** (depending on environment) Plug type**MC4-compatible** Conductor materialCopper (fine stranded, tinned) Protection type**IP68** (dust and waterproof) Operating temperature**-40°C to +90°C** Colour1x red (+), 1x black (-)  FAQs about the solar extension cable 12mIs the power loss already too high at 12 metres?No, not for typical applications. With a typical balcony system or a string with e.g. 10 amps, the voltage drop at 12 metres (4mm²) is about 1.5 to 2 volts. This corresponds to a loss of around 1-2%, which is absolutely within the acceptable range. Only in extreme low-light or very high current situations would a 6mm² cable be more advantageous.Can I also install the cable indoors?Yes, absolutely. The cables are designed for rugged outdoor use (UV/weather), but can also be safely used indoors, in cable ducts, or behind drywall. They are halogen-free and flame-retardant.Do the connectors fit every inverter?Usually, yes. Almost all modern PV modules and microinverters (e.g. Hoymiles, Deye, NEP) use the MC4 standard (or compatible types such as TS4). The connections on this cable are mechanically and electrically suitable for them.

With this solar extension cable set (15 metres, 4mm²) you can also master extensive installations and challenging cable routes. A length of 15 metres gives you enormous freedom: you can place your solar modules where solar irradiation is highest (e.g. at the end of the garden or on an outbuilding), while the inverter or the battery is safely housed indoors or in the basement.The set consists of two high-quality, double-insulated PV cables (1x red for positive, 1x black for negative). Both cables are already professionally fitted with MC4-compatible plugs and sockets pre-assembled ("Plug & Play"), so you do not need any special tools. The conductor made from tinned copper guarantees good conductivity and corrosion resistance even over this long distance.Highlights at a glanceMaximum flexibility: 15 metres of cable length bridge large distances between the generator field (modules) and the technical room.Plug & Play: Ready for immediate use thanks to pre-installed MC4-compatible plug connectors (male/female).Fault protection: The colour set consisting of Red (+) and Black (-) ensures a clear assignment of the poles and prevents dangerous polarity reversal.Weatherproof & robust: The special insulation made of cross-linked polyolefin is extremely UV-resistant, ozone-resistant and withstands temperatures from -40°C to +90°C.IP67 protection class: The connections are dustproof and water-resistant (short-term immersion) when plugged in.Certified quality: Meets common standards (e.g. EN 50618) for voltages up to 1500V DC.Areas of applicationThe 15-metre extension is ideal for installations with long distances:Ground-mounted systems in the garden: If the modules have to be located far from the house to avoid shading.Outbuildings: Connecting modules on the garage, carport or shed to the main building.Complex cable routing: When cables need to go round many corners, through empty pipes or shafts and a "direct line" is not possible.Facade systems: For conducting the DC lines from high facade positions to the basement.Installation & safety instructionsNote line losses: At a cable length of 15 metres (total 30 m circuit) a physical resistance is created. For typical PV applications (high voltages for strings or micro-inverters), 4mm² is fine. However, in pure 12V stand-alone systems (charging a battery), the voltage drop would be too high — here thicker cables or shorter runs should be selected.Do not coil cables: Avoid winding excess cables into rings (coil effect/heat development). Rather, lay it in loops.Use protective tubing: When laying in the ground or in areas with the risk of rodents (attic/garden), a protective tube (empty tube/corrugated tube) is strongly recommended.Strain relief: The high weight of 15m of cable must not pull on the small connectors of the solar module. Secure the first section of cable tightly to the module frame. Features Product nameSolar extension cable set (15 m) Cable length**15.0 metres** (per cable) Cable cross-section**4.0 mm²** Cable type**H1Z2Z2-K** (PV cable) Rated voltage**1500 V DC** Conductor materialElectrolytic copper, tinned (Class 5) Plug connectors**MC4-compatible** (crimped) Type of protection**IP68** (plugged) Temperature range-40°C to +90°C CertificatesTÜV Rheinland / CE / EN 50618  FAQs about the 15m solar extension cableIs a 4mm² cable still efficient at 15 metres in length?For grid-connected systems: Yes. If you use the cables for a balcony system or a roof installation (voltage approx. 30-40V or higher), the loss is acceptable (approx. 2-3%). For 12V stand-alone systems: No. If you wish to connect a 12V module directly to a battery, the voltage drop at 15m is too high. In this case, 6mm² or, preferably, 10mm² cable is required.Are the cables suitable for direct burial?No. Although the cables are extremely weather-resistant ("like earth cables"), they are not protected against mechanical damage (stones, spade cut, animal bites). Outdoors at ground level, you should always use an inexpensive PE pipe or flexible conduit as a protective sheath.Do the connectors fit my balcony system?Yes. The MC4 standard (and compatible types) is used by almost all module manufacturers and micro-inverters (Hoymiles, Deye, NEP etc.). The connectors fit together mechanically.

With this solar extension cable set (20 metres, 4mm²) you can bridge enormous distances between your solar modules and the technology. This length is ideal when you need to place your panels in a sunny spot in the garden, on a distant garage or an outbuilding, while the inverter or storage system is installed centrally in the house.The set consists of two double-insulated PV cables (1x red for plus, 1x black for minus). Both ends are already professionally fitted with MC4-compatible plugs and sockets ("Plug & Play"). The conductor made of tinned copper ensures durability; with this long length, the physical voltage drop should be taken into account (see notes). The cables are designed for permanent outdoor use in all weather conditions.Highlights at a glanceEnormous range: 20 metres in length gives you maximum freedom in choosing the location of your modules, far from the house connection.Plug & Play: Ready for immediate use thanks to pre-assembled MC4-compatible connectors (no crimping needed).Safety set: The colour combination red (+) and black (-) prevents polarity errors over long distances, where you might often lose track.Weatherproof (IP67): The plug connections are dustproof and waterproof; the insulation withstands extreme temperatures (-40°C to +90°C).UV- & ozone-resistant: The robust sheath made of cross-linked polyolefin does not become brittle even after years in the sun.Certified quality: Suitable for system voltages up to 1000V/1500V DC (TÜV/EN standards).Areas of applicationThe 20-metre extension is designed for extensive installations:Ground-mounted systems: Placement of the modules at the end of the property for optimum solar yield.Outbuildings: Connection from garden shed, carport or barn to the main house.Façade installation: Routing the cables from high roofs or façades down to the basement technical room.Shading management: Avoiding large sources of shade (trees, neighbouring buildings) by installing panels further away.Installation & safety instructionsNote voltage drop: With 20 metres length (40m current path there and back), resistance occurs. For grid-connected high-voltage systems (strings with several modules, >100V) 4mm² is unproblematic. For individual 12V/24V modules or standalone/off-grid systems, the loss at 4mm² is noticeable (approx. 3-5%). A 6mm² cable would be more efficient here.Do not create coils: Never wind excess cable into tight coils under high current (induction heating). Instead, lay it in large loops.Mechanical protection: Never lay the cable of this length unprotected on the ground (lawnmowers, animals!). Use cable ducts or protective tubes.Strain relief: Secure the cable immediately after connecting it to the module so that the weight of 20m of cable does not pull on the junction box. Properties Product nameSolar extension cable set (20 m) Cable length**20.0 metres** (per cable) Cable cross-section**4.0 mm²** Cable type**H1Z2Z2-K** (solar cable) Rated voltage**1500 V DC** Conductor materialTinned stranded copper wire (class 5) Connector**MC4-compatible** (male/female) Protection class**IP68** (connected) Temperature range-40°C to +90°C Special featureSet: 1x red (+) / 1x black (-)  FAQs about the 20m solar extension cableIs 4mm² still sufficient for 20 metres in length?Depends on the application. For a typical "balcony power station" (approx. 30-40V module voltage), the loss at full load is around 3-4%. This is technically safe, but means a slight reduction in output. For high-voltage strings (e.g. 300V), the percentage loss is negligible. For 12V systems (campers/battery charging), the voltage drop is too high; here we recommend 6mm² or 10mm².Can I bury the cable?Only in protective conduit. The insulation is weather-resistant but not certified for direct burial (risks: stones, moisture, rodents). A simple PE empty conduit from a DIY store provides sufficient protection.Are the connectors compatible with every inverter?Yes. The MC4 standard is universal. The cables suit all common modules and inverters (Hoymiles, Deye, Growatt etc.).

The solar extension cable set (25 metres, 4mm²) is the solution for photovoltaic projects with extreme distances. If your solar modules need to be located in the sunniest place on the property – for example at the end of a large garden, on a distant barn or in an open field – and the inverter is to remain centrally in the house, this set bridges the distance safely and reliably.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Due to the considerable length of 25 metres, this set is primarily designed for systems with a higher string voltage (e.g. several modules in series or grid-connected balcony power plants) in order to keep line losses low.Highlights at a glanceMaximum range: With a length of 25 metres (50 metres in the circuit) you can also implement complex installation scenarios far from the house connection.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: The colour coding in Red (+) and Black (-) effectively prevents polarity mix-ups with such a long cable run.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: When plugged in, the connectors are completely dustproof and protected against temporary submersion (rain/puddles).High-quality conductor: Tin-plated electrolytic copper ensures corrosion resistance and consistently good conductivity.Areas of applicationThis 25 metre extension is intended for specific scenarios:Ground-mounted systems: Ideal for installing modules far away in the garden or on a meadow where there is no shading from buildings.Outbuilding: Connection of distant garages, carports, sheds or stables to the main building.Indirect cable routing: When cables cannot be laid directly, but have to be routed around the entire house or through long empty conduits.Installation & Safety InstructionsVoltage drop (Important!): At 25 metres length, the total current path is 50 metres.For grid-connected systems (voltage > 30V) 4mm² is usually acceptable (loss approx. 3-5%).For 12V off-grid systems this cable is not suitable, as the voltage drop would be too high. Here, 10mm² or 16mm² would have to be used.Laying in the ground: Although the cable is weatherproof, it is not protected against mechanical influences (stones, rodents, spades).When laying underground, it is essential to use a protective conduit (KG conduit or flexible conduit).Avoid induction: Never wind excess cable into a coil while current is flowing, as this can lead to heat buildup.Lay excess lengths in wide loops ("meanders"). Properties Product nameSolar extension cable set (25 m) Cable length**25.0 metres** (per cable) Cable cross-section**4.0 mm²** Cable type**H1Z2Z2-K** (solar cable) Nominal voltage**1500 V DC** Conductor materialElectrolytic copper, tin-plated (class 5) Connector**MC4-compatible** (Male/Female) Protection class**IP68** (plugged) Temperature range-40°C to +90°C Scope of delivery1x cable Red (+) / 1x cable Black (-) FAQs about the solar extension cable 25mIs 4mm² really sufficient at 25 metres length?Yes for high-voltage systems, no for 12V systems. With a typical balcony power plant (approx. 30-40V module voltage, approx. 10A current) you will have a voltage drop of approx. 2 volts. This means a power loss of about 4-5%. This is technically safe, but not optimal. If you need every watt, you should upgrade to 6mm² cable at this length. For a 12V battery application, almost 1 volt would be lost – that's too much!Will the connectors fit my inverter from Hoymiles or Deye?Yes. The connectors used correspond to the MC4 standard, which is used for almost all solar modules and micro inverters worldwide. They fit mechanically and electrically perfectly.Can I shorten the cable?Yes, but with effort. You can cut the cable to the required length. Please note, however, that you will then need new MC4 connectors and a special crimping tool to reassemble the connection.

The Solar extension cable set (1 metre, 6mm²) is the compact high-performance solution for photovoltaic projects where maximum efficiency is required in the smallest of spaces. If you only need to bridge short distances – for example, between closely spaced modules or directly to the microinverter of a balcony power station – this large cross-section ensures there is no loss of power, even at peak currents.The set contains two high-quality, double-insulated solar cables: one red cable for the positive terminal (+) and one black cable for the negative terminal (–). Both ends are professionally pre-assembled with MC4-compatible connectors and sockets. Thanks to the generous cross-section of 6mm², this set is extremely future-proof and ideal for modern high-performance modules with very high output currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section minimises electrical resistance to an absolute minimum, which is especially beneficial for high currents.Plug & Play installation: The cables are factory-fitted on both sides with MC4-compatible plugs, so no special crimping tools are required.Secure identification: The clear colour coding in red (+) and black (–) effectively prevents a polarity reversal when connecting.Weatherproof & Durable: The special sheath made from cross-linked polyolefin is UV-resistant, ozone-resistant, and can withstand extremely low and high temperatures from –40°C to +90°C.Protection class IP67: When mated, the connectors are absolutely dust-tight and protected against splashing water and rain.High-quality conductor: Tinned electrolytic copper provides excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 1-metre extension is optimised for specific short-range scenarios:Module connection (string)Bridging short distances between two solar modules if the factory-installed cables are just too short for the selected mounting position.Balcony power stationsDirect connection from the module to the microinverter if the latter is attached directly behind the panel on the mounting frame.Compact stand-alone systemsConnecting small charge controllers in camper vans or boats, where the components are installed in confined spaces.Assembly & safety informationNo measurable voltage dropAt a length of only 1 metre, the voltage loss is practically zero, even in 12V systems. This makes the cable the ideal choice for perfectionists who want to make use of every last bit of energy.Observe bend radiusDespite the high flexibility of the finely stranded conductors, you should not bend the 6mm² cable too sharply, to avoid mechanically stressing the insulation and the connectors.Correct latchingWhen connecting, make sure the MC4 connectors clearly click into place. This is the only way to ensure the connection is permanently waterproof and safe from arcing. Features ModelSolar extension cable set (1m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**1.0 metre** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on conductor) CertificationTÜV / EN 50618 (H1Z2Z2-K) Special featureVery low resistance & UV-resistant  FAQs on the solar extension cable 1mIsn't 6mm² oversized for just 1 metre in length?Technically yes, but it never hurts. While 4mm² is usually sufficient at this length, 6mm² offers greater mechanical robustness and is already ideal for future module generations with currents above 15A.Will this cable fit my inverter from Hoymiles or Deye?Yes. The connectors used comply with the MC4 standard, which is used worldwide in almost all solar modules and microinverters. They fit perfectly both mechanically and electrically.Can I connect two of these 1m cables in series?Yes, that is possible. The cables can be cascaded as needed. Please note, however, that each connector represents a tiny contact resistance. For short overall distances, however, this is negligible.

The Solar extension cable set (2 metres, 6mm²) is the compact, high-performance solution for photovoltaic projects where maximum efficiency is required in the tightest of spaces. If you only need to bridge short distances – for example, between closely spaced modules or directly to the micro inverter of a balcony power station – this large cross-section ensures that not a single watt of power is lost, even at peak currents.The set contains two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (–). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the generous cross-section of 6mm², this set is extremely future-proof and ideal for modern high-performance modules with very high output currents.Highlights at a glanceMaximum efficiency: The cross-section of 6mm² minimises electrical resistance to an absolute minimum, which is especially advantageous for high currents.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: The clear colour coding in red (+) and black (–) effectively prevents incorrect polarity when connecting.Weatherproof & durable: The special jacket made from cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection rating IP67: When mated, the connectors are absolutely dust-tight and protected against splash water and rain.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and long-lasting high conductivity.Areas of applicationThis 2-metre extension is optimised for specific close-range scenarios:Module connection (string)Bridging short distances between two solar modules where the factory cables are just a little too short for the chosen mounting position.Balcony power stationsDirect connection from the module to the micro inverter if it is mounted directly behind the panel on the mounting frame.Compact stand-alone systemsConnecting small charge controllers in motorhomes or boats where components are installed in confined spaces.Assembly & safety instructionsNo measurable voltage dropAt a length of just 2 metres, the voltage loss is practically zero, even with 12V systems. This makes the cable the perfect choice for perfectionists who want to utilise every bit of energy.Observe bending radiiDespite the high flexibility of the fine-stranded conductors, you should not bend the 6mm² cable too sharply in order not to mechanically stress the insulation and connectors.Correct latchingWhen connecting, make sure that the MC4 connectors audibly engage. Only then is the connection permanently waterproof and safe against arcing. Features ModelSolar extension cable set (2m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**2.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureVery low resistance & halogen-free  FAQs about the solar extension cable 2m 6mm²Isn’t 6mm² oversized for a length of just 2 metres?Technically yes, but it offers reserves. While 4mm² is usually sufficient for this length, 6mm² offers higher mechanical robustness and is already perfectly equipped for future module generations with currents above 15A.Does the cable fit my inverter from Hoymiles or Deye?Yes. The connectors used comply with the MC4 standard, which is used worldwide for almost all solar modules and micro inverters. They fit mechanically and electrically perfectly.Can I connect two of these 2m cables end to end?Yes, that is possible. The cables can be cascaded as required. Please note, however, that each connection represents a tiny contact resistance. For short overall distances, however, this is negligible.

The solar extension cable set (3 metres, 6mm²) is the ideal solution for short distances within a photovoltaic installation where maximum efficiency and sustainability are paramount. If you need to bridge gaps between your solar modules or make the connection to an inverter or charge controller, this generous cross-section of 6mm² gives you the certainty that not a single watt of power will be lost, even at peak currents.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the solid cross-section, this set is particularly robust and ideal for modern high-performance modules that often deliver very high currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section minimises electrical resistance to an absolute minimum, which is particularly advantageous at high currents.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tools are required.Safe identification: The clear colour coding in red (+) and black (-) effectively prevents incorrect polarity when connecting.Weatherproof & Durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection class: The plug connections are absolutely dust-tight and protected against splash water and rain when plugged in.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 3-metre extension is designed for a variety of application scenarios:Balcony power plantsPerfect for bridging the distance between the solar modules and the inverter when it is mounted slightly offset.String cablingBridging gaps between module arrays on pitched roofs or on flat roof elevations.Motorhomes & CampingConnecting solar modules to the charge controller in tight spaces where the components are installed in the smallest possible area.Installation & safety instructionsNo measurable voltage dropAt only 3 metres in length, the voltage loss is virtually zero even with 12V systems. This makes the cable the ideal choice for perfectionists who want to use every bit of energy.Observe bending radiiDespite the high flexibility of the fine-stranded conductors, you should not bend the 6mm² cable too sharply so as not to place mechanical stress on the insulation and connectors.Correct lockingMake sure you hear the MC4 connectors click into place when you connect them. Only then is the connection permanently watertight and safe from electric arcs. Features ModelSolar extension cable set (3m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**3.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine-stranded) Temperature range-40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureLow-loss & extremely weather-resistant FAQs about the solar extension cable 3m 6mm²Isn't 6mm² oversized for just 3 metres in length?Technically yes, but it offers reserves. While 4mm² is generally sufficient for this length, 6mm² offers increased mechanical robustness and is already ideally suited for future module generations with currents above 15A.Will the plugs fit my inverter from Hoymiles or Deye?Yes. The installed connectors conform to the MC4 standard, which is used worldwide in almost all solar modules and microinverters. They fit perfectly both mechanically and electrically.Can I also leave these cables outside?Yes, that's what they are designed for. The cables are certified according to common PV standards. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.

The solar extension cable set (5 metres, 6mm²) is the ideal solution for moderate distances within a photovoltaic installation where maximum efficiency and future viability are paramount. If you have to bridge distances between your solar modules or want to connect to an inverter or charge controller, this generous cross-section of 6mm² offers the assurance that not even a watt of power is lost, even at peak currents.The set includes two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the length of 5 metres and the solid cross-section of 6mm², this set is technically excellently dimensioned for virtually all common PV applications (balcony power stations, stand-alone systems, rooftop systems).Highlights at a glanceMaximum efficiency: The 6mm² cross-section minimises electrical resistance to an absolute minimum, which is particularly advantageous for high currents.Plug & Play installation: The cables are fully assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Safe identification: The clear colour coding in red (+) and black (-) effectively prevents incorrect polarity during connection.Weatherproof & Durable: The special sheath made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection rating: The connectors are absolutely dustproof and protected against splashing water and rain when plugged in.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity.Areas of applicationThis 5-metre extension is designed for a variety of application scenarios:Balcony power stationsPerfect for bridging the distance between the solar modules and the inverter if the latter is mounted offset on the railing or on the wall.String cablingBridging gaps between module fields on pitched roofs or flat roof supports.Motorhomes & CampingConnecting solar modules to the charge controller, so that the vehicle can be parked in the shade while the panels are positioned in the sun.Assembly & safety instructionsNo measurable voltage dropAt a length of 5 metres, the voltage loss is negligible even for 12V systems. This makes the cable the ideal choice for perfectionists who want to achieve maximum yields.Strain reliefFix the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical tension on the connectors and module junction boxes.Correct latchingMake sure that the MC4 connectors audibly click into place when plugging together. This is the only way to ensure that the connection is permanently watertight and safe against arcing. Features ModelSolar extension cable set (5m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**5.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureLow-loss & extremely weather-resistant  FAQs about the solar extension cable 5m 6mm²Why should I choose 6mm² instead of 4mm² for 5 metres?For maximum future viability. Although 4mm² is often sufficient for 5 metres, 6mm² offers greater mechanical stability and is already well equipped for modern modules with currents over 15A. In addition, the cable stays cooler under high loads.Do the connectors fit modules of all well-known brands?Yes. These cables use MC4-compatible standard connectors. These fit mechanically and electrically perfectly to the connections of manufacturers such as Trina, Jinko, JA Solar or Canadian Solar.Can I also leave these cables outdoors?Yes, they are designed for this purpose. The cables are certified to common PV standards. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.

The solar extension cable set (8 metres, 6mm²) is the ideal solution for moderate distances within a photovoltaic installation where maximum efficiency and future-proofing are paramount. If you need to bridge gaps between your solar modules or want to connect to an inverter or charge controller, this generous 6mm² cross-section ensures that not a single watt of power is lost, even during peak currents.The set includes two high-quality, double-insulated solar cables: a red cable for the positive terminal (+) and a black cable for the negative terminal (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the 8-metre length and solid 6mm² cross-section, this set is technically perfectly dimensioned for almost all common PV applications (balcony power plants, stand-alone systems, roof systems).Highlights at a glanceMaximum efficiency: The 6mm² cross-section minimises electrical resistance to an absolute minimum, which is particularly advantageous for high currents (e.g. modern 400W+ modules).Plug & Play installation: The cables come pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: The clear colour coding in red (+) and black (-) effectively prevents incorrect polarity along the entire connection length.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection rating IP67: The connectors are completely dustproof and protected against splash water and rain when plugged in.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and consistently high conductivity.Areas of applicationThis 8-metre extension is designed for a wide range of application scenarios:Balcony power plantsPerfect to bridge the distance between the solar modules and the inverter if this is mounted offset on the railing, wall or indoors.String cablingBridging gaps between module fields on pitched roofs, carports or flat roof structures.Motorhomes & campingConnecting the solar modules to the charge controller, so you can park the vehicle flexibly in the shade while the panels are positioned in the sun.Installation & safety instructionsNegligible voltage dropAt a length of 8 metres, the 6mm² cross-section provides extremely stable energy transmission. This makes the cable the ideal choice for perfectionists who want to get the maximum yield from their system.Strain reliefSecure the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical strain on the plug connections to ensure lasting tightness of the MC4 connectors.Correct lockingWhen connecting, make sure that the MC4 connectors audibly click into place. Only then will the connection be permanently waterproof and safely protected against arcing. Features ModelSolar extension cable set (8m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**8.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range-40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely weather-resistant & low-loss  FAQs about the solar extension cable 8m 6mm²Why should I choose 6mm² instead of 4mm² for 8 metres?For maximum safety and efficiency. Although 4mm² is often sufficient for 8 metres, 6mm² offers higher mechanical robustness and stays cooler under high loads (many amps). It is a future-proof investment for modern modules with high output currents.Do the connectors fit modules from all well-known brands?Yes. These cables use MC4-compatible standard connectors. They fit perfectly mechanically and electrically to the connections of manufacturers such as Trina Solar, Jinko, JA Solar, Longi or Canadian Solar.Can I leave these cables outdoors?Yes, that's what they are designed for. The cables are certified to current PV standards. They are resistant to ammonia, ozone and UV radiation and can be used outdoors for decades.

The Solar extension cable set (10 metres, 6mm²) is the high-performance solution for photovoltaic projects where maximum efficiency and minimum losses are paramount. If you need to bridge a distance of 10 metres between your solar modules and the inverter, this generous cross-section of 6mm² offers the necessary reserves to safely transmit the generated energy to its destination without any significant heat development.The set contains two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. The solid cross-section makes this set particularly future-proof and ideal for modern high-performance modules, which often deliver high currents and where standard cables could already reach their limits.Highlights at a glanceLowest line losses: The cross-section of 6mm² massively minimises the electrical resistance and ensures a significantly lower voltage drop than conventional 4mm² cables.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors so that no special tools are required for crimping.Secure identification: The colour coding in red (+) and black (-) effectively prevents incorrect polarity and makes installation easier, even with more complex systems.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and can withstand extreme temperatures from -40°C to +90°C.Protection class IP67: The connectors are absolutely dust-tight when plugged in and protected against temporary submersion (rain/puddles).High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and consistently high conductivity, even in salty air.Areas of applicationThis 10-metre extension is optimised for demanding scenarios:Powerful balcony stationsIdeal for systems with 800W or more, to ensure every watt is transferred from the balcony or garage roof to the inverter without loss, even in full midday sun.Roof installations & carportsBridging the distance from the modules to the entry point into the building or directly to the string inverter.Off-grid systems (12V / 24V)Especially important for battery systems: The 6mm² cross-section ensures that the charging voltage reaches the battery almost loss-free, which noticeably increases charging efficiency.Assembly & safety instructionsEfficiency advantageFor a cable length of 10 metres, 6mm² provides a clear advantage over 4mm², as the resistance is about a third lower. This means more yield for your system over the entire service life.Strain reliefFix the cables using UV-resistant cable ties to the mounting frame. Avoid mechanical strain on the connectors and the module junction boxes.Proper latchingWhen connecting the MC4 connectors, make sure they audibly click into place. This is the only way to ensure that the connection is permanently watertight and safe against dangerous arcs. Features ModelSolar extension cable set (10m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**10.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely weather-resistant & low-loss  FAQs about the solar extension cable 10m 6mm²Why should I choose 6mm² instead of 4mm²?For more yield and safety. Although 4mm² is often technically sufficient, the resistance decreases with 6mm². This leads to less heat development in the cable and a higher voltage at the inverter. Especially for modules with high currents (13A and more), 6mm² is the technically superior choice.Do the connectors fit my inverter from Growatt or Victron?Yes. The connectors used comply with the global MC4 standard. They fit mechanically and electrically perfectly to the connections of almost all common solar modules, micro inverters and charge controllers.Can I shorten the cable if necessary?Yes, with the right tool. You can cut the cable to size. However, please note that you will need professional MC4 connectors and special crimping pliers for the new connection to ensure a permanently secure connection.

The Solar extension cable set (12 metres, 6mm²) is the high-performance solution for photovoltaic projects where maximum efficiency and minimum losses are paramount. If you need to bridge a distance of 12 metres between your solar modules and the inverter, this generous cross-section of 6mm² offers the necessary reserves to safely guide the energy generated to its destination without significant heat generation.The set includes two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible connectors and sockets. Thanks to the massive cross-section, this set is particularly future-proof and ideal for modern high-performance modules, which often deliver high currents and for which standard cables could already reach their limits.Highlights at a glanceLowest line losses: The cross-section of 6mm² massively minimises electrical resistance and ensures a clearly lower voltage drop than conventional 4mm² cables.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Safe identification: The colour coding in red (+) and black (-) effectively prevents incorrect polarity and also makes installation easier for more complex systems.Weatherproof & durable: The special sheath made from cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: When plugged in, the connectors are absolutely dustproof and protected against temporary submersion (rain/puddles).High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity, even in salty air.Areas of applicationThis 12-metre extension is optimised for demanding scenarios:High-performance balcony power systemsIdeal for systems with 800W or more to carry every watt from the balcony or garage roof to the inverter without loss, even at midday sun at full output.Roof systems & carportsBridging the distance from the modules to the entry point into the building or directly to the string inverter.Off-grid systems (12V / 24V)Particularly critical for battery systems: The 6mm² cross-section ensures that the charging voltage reaches the battery almost loss-free, which measurably increases charging efficiency.Assembly & safety notesEfficiency advantageWith a length of 12 metres, 6mm² offers a marked advantage over 4mm², as the resistance is around one third lower. That means more yield for your system throughout its entire lifetime.Strain reliefFasten the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical tension on the plug-in connections and module connection boxes.Proper latchingWhen plugging them together, make sure that the MC4 connectors click audibly into place. Only then will the connection be permanently watertight and safe from dangerous arcing. Features ModelSolar extension cable set (12m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**12.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely weather-resistant & low-loss  FAQs about the solar extension cable 12m 6mm²Why should I choose 6mm² instead of 4mm²?For more yield and safety. Although 4mm² is often technically sufficient, 6mm² reduces the resistance. This results in less heat generation in the cable and higher voltage at the inverter. Especially with modules with high currents (13A and above), 6mm² is the technically superior option.Do the connectors fit my inverter from Growatt or Victron?Yes. The connectors used comply with the global MC4 standard. They fit perfectly mechanically and electrically to the connections of almost all standard solar modules, micro-inverters and charge controllers.Can I shorten the cable if necessary?Yes, with the right tool. You can cut the cable. However, please note that for the new connection you will need professional MC4 connectors and a special crimping tool to ensure a permanently secure connection.

The solar extension cable set (15 metres, 6mm²) is the high-performance solution for photovoltaic projects where maximum efficiency and minimal losses are paramount. If you need to bridge a distance of 15 metres between your solar modules and the inverter, this generous 6mm² cross-section provides the necessary reserves to safely deliver the generated energy to its destination without significant heat development.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (–). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Due to its large cross-section, this set is particularly future-proof and ideal for modern high-performance modules that often deliver high currents, where standard cables may reach their limits.Highlights at a glanceLowest cable losses: The 6mm² cross-section massively minimises electrical resistance and results in a significantly lower voltage drop than conventional 4mm² cables.Plug & Play installation: The cables are fully pre-assembled on both sides with MC4-compatible connectors, so no special crimping tools are required.Safe identification: The red (+) and black (–) colour coding effectively prevents incorrect polarity and simplifies installation, even in more complex systems.Weatherproof & durable: The special cross-linked polyolefin sheath is UV-resistant, ozone-resistant and withstands extreme temperatures from –40°C to +90°C.IP67 protection rating: When connected, the connectors are completely dustproof and protected against temporary submersion (rain/puddles).High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity, even in salty air.Areas of applicationThis 15-metre extension is optimised for demanding scenarios:High-power balcony power plantsIdeal for systems with 800W or more, to transmit every watt from balcony or garage roof to inverter loss-free, even in full midday sun.Roof systems & carportsBridging the distance from the modules to the entry point into the building or directly to the string inverter.Off-grid systems (12V / 24V)Especially critical for battery systems: The 6mm² cross-section ensures that the charging voltage reaches the battery almost loss-free, which noticeably increases charging efficiency.Assembly & safety instructionsEfficiency advantageWith 15 metres cable length, 6mm² provides a clear advantage over 4mm² as resistance is reduced by about a third. This means more yield for your system over its entire service life.Strain reliefFix the cables to the mounting frame with UV-resistant cable ties. Avoid mechanical tension on the connectors and module connection boxes.Correct lockingWhen plugging them together, ensure the MC4 connectors audibly click into place. Only then is the connection permanently watertight and safe from hazardous arcs. Features ModelSolar extension cable set (15m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**15.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range–40°C to +120°C (on the conductor) StandardsTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely low-loss & weather-resistant  FAQs about the solar extension cable 15m 6mm²Why should I choose 6mm² instead of 4mm²?For more yield and safety. Although 4mm² is often technically sufficient, the resistance is lower with 6mm². This leads to less heat build-up in the cable and higher voltage at the inverter. Especially with modules supplying high currents (13A or more), 6mm² is the technically superior choice.Will the connectors fit my inverter from Growatt or Victron?Yes. The assembled connectors meet the worldwide MC4 standard. They fit mechanically and electrically perfectly with the connections of almost all common solar modules, micro inverters and charge controllers.Can I shorten the cable if necessary?Yes, with the right tool. You can cut the cable to length. Please note, however, that you will need professional MC4 connectors and a special crimping tool for the new connection to ensure a permanently safe connection.

The solar extension cable set (20 metres, 6mm²) is the high-performance solution for photovoltaic projects where maximum efficiency and minimum losses over long distances are paramount. If you need to bridge a distance of 20 metres between your solar modules and the inverter, this generous cross-section of 6mm² offers the necessary reserves to safely transmit the generated energy to its destination without any significant heat build-up.The set contains two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally fitted with MC4-compatible plugs and sockets. The solid cross-section makes this set particularly future-proof and ideal for modern high-performance modules, which often deliver high currents and where standard cables already reach their limits at this distance.Highlights at a glanceLowest line losses: The cross-section of 6mm² drastically reduces electrical resistance and ensures a much lower voltage drop than conventional 4mm² cables over 20 metres.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: The colour coding in red (+) and black (-) effectively prevents incorrect polarity and makes installation easier even with more complex systems.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection class: The connectors are absolutely dustproof when plugged in and protected against temporary submersion (rain/puddles).High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity, even in demanding environments.Areas of applicationThis 20-metre extension is optimised for demanding long-distance connections:Large balcony power plants & garden systemsIdeal for placing modules at the sunny end of a garden or on a carport and routing the electricity with minimal loss over 20 metres to the house.Roof systems & barnsBridging the distance from far-off module strings to the point of entry into the building or to the central inverter.Off-grid systems (12V / 24V / 48V)Particularly critical for battery systems: At 20 metres, the 6mm² cross-section ensures that the charging voltage arrives almost loss-free, noticeably increasing the efficiency of your storage unit.Assembly & safety instructionsEfficiency advantage over distanceAt 20 metres cable length, 6mm² offers a significant advantage over 4mm². The lower resistance provides a higher system voltage at the inverter and thus measurably more yield.Strain relief & fixationFasten the long cable paths every 50-100 cm with UV-resistant cable ties to the mounting frame or in cable ducts to avoid mechanical strain on the connectors.Correct lockingWhen connecting, make sure that the MC4 connectors audibly engage. Only then is the connection permanently watertight and safe against dangerous arcing. Features ModelSolar extension cable set (20m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**20.0 metres** (per colour) Nominal voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureVery low resistance & loss-optimised FAQs about the solar extension cable 20m 6mm²Why should I choose 6mm² for 20m?To minimise power losses. At a length of 20 metres (40m total distance), the resistance adds up. 6mm² cables have around 30% less resistance than 4mm² cables. This means less heat loss in the cable and more usable energy for your inverter.Do the connectors fit modules from all common manufacturers?Yes. The connectors used comply with the worldwide MC4 standard. They fit mechanically and electrically perfectly to connections on brands such as Trina, Jinko, JA Solar or Canadian Solar.Can I shorten the cable if necessary?Yes, with expertise. You can cut the cable. Please note, however, that you will need professional MC4 connectors and special crimping pliers for the new connection to ensure a permanently safe connection.

The Solar extension cable set (25 metres, 6mm²) is the high-performance solution for photovoltaic projects where maximum efficiency and minimal losses over long distances are paramount. If you need to bridge a distance of 25 metres between your solar modules and the inverter, this generous cross-section of 6mm² provides the necessary reserves to safely carry the generated energy to its destination without any significant heat build-up.The set includes two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the solid cross-section, this set is particularly future-proof and ideal for modern high-performance modules that often deliver high currents and where standard cables already reach their limits at this distance.Highlights at a glanceLowest line losses: The 6mm² cross-section significantly minimises electrical resistance and ensures a much lower voltage drop than conventional 4mm² cables over 25 metres.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tools are required.Secure identification: The colour coding in red (+) and black (-) effectively prevents incorrect polarity and makes installation easier, even on more complex systems.Weatherproof & durable: The special jacket made from cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: The connectors are absolutely dust-tight and protected against temporary submersion (rain/puddles) when plugged in.High-quality conductor: Tinned electrolytic copper ensures excellent corrosion resistance and permanently high conductivity, even in demanding environments.Areas of applicationThis 25-metre extension is optimised for demanding long-distance connections:Large balcony power stations & garden systemsIdeal for placing modules at the sunny end of a garden or on a carport and routing the electricity to the house with minimal loss over 25 metres.Rooftop systems & barnsBridging the distance from distant module strings to the entry point into the building or to the central inverter.Stand-alone systems (12V / 24V / 48V)Especially critical for battery systems: Over 25 metres, the 6mm² cross-section ensures that the charging voltage arrives virtually without loss, which noticeably increases the efficiency of your storage.Assembly & safety instructionsEfficiency advantage at distanceWith a cable length of 25 metres, 6mm² provides a significant advantage over 4mm². The reduced resistance means a higher system voltage at the inverter, resulting in a measurably higher yield.Strain relief & fixationFix the long cable runs every 50–100 cm to the mounting frame or in cable ducts using UV-resistant cable ties to prevent mechanical strain on the connectors.Proper latchingWhen connecting, make sure that the MC4 connectors audibly latch. This is the only way to ensure that the connection is permanently waterproof and safe against dangerous arcing. Features ModelSolar extension cable set (25m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**25.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureOptimised for minimised losses across long runs & UV resistant  FAQs about the Solar Extension Cable 25m 6mm²Why should I use 6mm² for 25m?To minimise power losses. At a length of 25 metres (50m total run) the resistance adds up. 6mm² cables have around a 30% lower resistance than 4mm² cables. This means less heat lost in the cable and more usable energy for your inverter.Do the connectors fit modules from all major manufacturers?Yes. The supplied connectors comply with the global MC4 standard. They fit perfectly both mechanically and electrically with connections from brands such as Trina, Jinko, JA Solar or Canadian Solar.Can I shorten the cable if required?Yes, with expertise. You can shorten the cable. Please note, however, that you will need professional MC4 connectors and a special crimping tool to ensure a permanently secure connection for the new end.

The solar extension cable set (30 metres, 6mm²) is the professional solution for photovoltaic projects that require maximum efficiency over very long distances. If your solar modules are installed on a remote open space, a carport or a barn and the distance to the inverter is 30 metres, this generous cross-section of 6mm² offers the necessary capacity to effectively minimise power losses.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Whereas a 4mm² cable already reaches its efficiency limits at a length of 30 metres, the 6mm² variant guarantees a more stable voltage and thus a higher overall yield from your system.Highlights at a glanceMinimised voltage drop: The cross-section of 6mm² offers approximately 30% less resistance than 4mm² cables, which is decisive for the yield for a length of 30 metres (60m total path).Plug & Play installation: The cables are fully pre-assembled with MC4-compatible connectors on both sides, so no special crimping tool is required.Safe identification: The clear colour coding in red (+) and black (-) effectively prevents dangerous polarity mix-ups over this long distance during installation.Weatherproof & durable: The special sheath, made of cross-linked polyolefin, is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: The connectors are absolutely dustproof and protected against temporary submersion (e.g. in heavy rain) when plugged together.High-quality conductor: Tinned electrolytic copper ensures maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 30-metre extension is optimised for demanding long-distance connections:Large ground-mounted systemsIdeal for positioning modules at the shade-free end of a large plot while the technology is protected indoors.Agriculture & outbuildingsConnecting distant barns, stables or garden sheds to the central feed-in point.Stand-alone systems (24V / 48V)For battery systems in particular, the 6mm² cross-section over 30 metres is essential to keep the charging voltage stable and efficiently charge the battery.Assembly & safety instructionsEfficiency at a distanceWith a cable length of 30 metres, the extra cost for 6mm² often pays for itself in a short time due to the reduced energy loss in the cable (less heat, more active power).Protection for underground installationAlthough the cable is weatherproof, it must be laid in a protective conduit (e.g. empty conduit or cable protection pipe) when laid in the ground to protect it from rodents and mechanical pressure.Correct latchingWhen connecting, make sure you hear the MC4 connectors engage audibly. Only then is the connection permanently watertight and safe against dangerous arcing. Features ModelSolar extension cable set (30m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**30.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureHalogen-free & UV-resistant FAQs about the solar extension cable 30m 6mm²Is 6mm² sufficient for 30 metres for a balcony power station?Yes, it is the recommended choice. While a 4mm² cable at this length can already cause losses of approximately 6-8% (depending on current), the 6mm² cable significantly reduces this loss. It is the technically most sensible solution for this distance.Are the connectors compatible with inverters from Growatt, Victron or Deye?Yes. The connectors used comply with the worldwide MC4 standard. They fit perfectly mechanically and electrically to the terminals of almost all common solar modules and inverters.Can I shorten the cable if 30m is too long?Yes, with expertise. You can cut the cable to length. However, bear in mind that you will need professional MC4 connectors and a special crimping tool for the new end to ensure a permanently secure connection.

The solar extension cable set (35 metres, 6mm²) is the specialised solution for photovoltaic projects with very long distances. If your solar modules need to be positioned at the sunniest place on your property – for example, at the end of a large garden or on a remote barn – and the inverter is centrally located in the building, this generous 6mm² cross-section provides the necessary capacity to effectively minimise power losses over the full 35-metre span.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (–). Both ends come professionally pre-assembled with MC4-compatible connectors and sockets. Thanks to the substantial cross-section, this set is particularly future-proof and ideal for modern high-performance modules, where standard cables (4mm²) would already show significant efficiency losses over this distance.Highlights at a GlanceOptimised for Long Distances: The 6mm² cross-section dramatically reduces electrical resistance, which is crucial for high energy yield over 35 metres (70m total route).Plug & Play Installation: The cables are factory-fitted with MC4-compatible connectors on both ends, so no specialised crimping tools are required.Safe Identification: Clear colour coding in red (+) and black (–) ensures dangerous polarity confusion is effectively prevented on this long cable run.Weatherproof & Durable: The special cross-linked polyolefin sheath is UV-resistant, ozone-proof, and withstands extreme temperatures from –40°C to +90°C.IP67 Protection: When mated, the connector assemblies are absolutely dust-tight and protected against temporary immersion (e.g., during heavy rain).High-Quality Conductor: Tinned electrolytic copper ensures maximum corrosion resistance and consistently excellent conductivity even in adverse conditions.Areas of ApplicationThis 35-metre extension is designed for demanding long-distance connections:Ground-mounted systemsIdeal for installing modules far away in the garden or on a meadow, where there is no shading from buildings.Outbuildings & AgricultureConnecting distant garages, carports, or stables to the main building.Off-grid systems (24V / 48V)Especially for battery systems, the 6mm² cross-section over 35 metres is important to keep the charging voltage stable and losses low.Assembly & Safety InstructionsEfficiency Over DistanceFor a cable length of 35 metres, 6mm² offers a significant advantage over 4mm². Lower resistance ensures higher system voltage at the inverter and thus measurably better yield over the years.Underground Installation ProtectionAlthough the cable is weatherproof, if running it underground it must always be routed in suitable protective conduit for protection against mechanical impacts and rodents.Correct LatchingWhen connecting, ensure the MC4 connectors audibly latch. This is the only way to ensure a permanently watertight and safe connection against dangerous arcing. Features ModelSolar extension cable set (35m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**35.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range–40°C to +120°C (at conductor) StandardTÜV / EN 50618 (H1Z2Z2-K) Special featureHalogen-free & UV-resistant FAQs about the Solar Extension Cable 35m 6mm²Why is 6mm² better than 4mm² at 35 metres?Because of the lower voltage drop. Over a total length of 70 metres (there and back) the resistance sums up. A 6mm² cable reduces this resistance by about a third compared to a 4mm² cable, which can mean several percent higher yield for typical balcony power stations or module strings.Will the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The connectors comply with the global MC4 standard and will fit mechanically and electrically with almost all common solar modules and inverters.Can I shorten the cable if 35m is too long?Yes, with expertise. You can cut the cable. However, please note that you will need professional MC4 connectors and a special PV crimping tool for the new connection to ensure a permanently reliable connection.

The solar extension cable set (30 metres, 4mm²) is the professional solution for photovoltaic projects where maximum flexibility and range are required. If your solar modules are to be installed on a remote open space, a carport or a barn and the path to the inverter or battery storage is a considerable distance away, you can bridge this distance safely and efficiently with this set.The set contains two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Due to the considerable length of 30 metres (60 metres total circuit path), this set is primarily designed for systems with high string voltage, to keep the percentage line losses low.Highlights at a glanceExtreme range: With 30 metres length per cable, even large properties and complex routing situations can be managed easily.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is needed.Secure identification: The clear colour coding in red (+) and black (-) effectively prevents polarity confusion during installation over long distances.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection: The connectors are completely dust-tight when plugged in and protected against temporary submersion (e.g. during heavy rain).High-quality conductor: Tinned electrolytic copper ensures maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 30-metre extension is optimised for specific scenarios:Large ground-mounted systemsIdeal for placing solar modules at the shade-free end of a garden or on a meadow, while the technology is installed in the house.Outbuildings & agricultureConnecting distant stables, barns or tool sheds with the main house connection or a feed-in point.Complex cable routingWhen cables cannot be laid directly but have to be routed around buildings or through widely branching duct systems.Assembly & safety instructionsVoltage drop (Important!)With 30 metres length, the total current path is 60 metres. For grid-connected systems with high voltage (> 60V), 4mm² is acceptable. For 12V or 24V stand-alone systems, this cable is not suitable due to the high voltage drop; here cross-sections of 10mm² or 16mm² should be chosen.Laying in the groundAlthough the cable is weather-resistant, it is not protected against mechanical stress (spade cuts, rodents). Always use a suitable protective conduit (flexible or cable protection conduit) for underground installation.Avoid induction & heatNever coil excess cable tightly when current is flowing, as this can cause heat build-up. Ideally, lay excess length in wide loops ("meandering"). Features ModelSolar extension cable set (30m) Conductor cross-section**4.0 mm²** Cable length**30.0 metres** (per colour) Rated voltage1000V / 1500V DC (max.) Connector type**MC4 compatible** (IP67) Temperature range-40°C to +120°C (at conductor) Conductor materialCopper, tinned (fine stranded) ApprovalsTÜV / EN 50618 Special featureHalogen-free & short-circuit proof  FAQs about the solar extension cable 30mIs 4mm² still efficient at 30 metres in length?For high-voltage systems, partially yes; for 12V systems, no. With a typical balcony plant (approx. 40V module voltage, 10A current), there will be a voltage drop of around 2.5 volts at 30m. This equates to approximately 6% power loss. This is technically safe but at the limit of efficiency. For maximum yields at this length, we recommend switching to 6mm² cables.Are the connectors compatible with my inverter from Hoymiles, Deye or TSUN?Yes. The connectors used adhere to the global MC4 standard. They fit mechanically and electrically flawlessly to almost all common solar modules and microinverters.Can I shorten the cable if necessary?Yes, with the proper tool. You can cut the cable. However, note that for the new connection, you will need professional MC4 plugs and a suitable crimping tool to ensure a permanently safe and watertight connection.

The solar extension cable set (35 metres, 4mm²) is the specialised solution for photovoltaic projects with very large distances. If your solar modules have to be positioned in the sunniest place on your property – for example, at the end of an extensive garden, on a distant barn or in an open field – and the inverter is to remain centrally located in the building, this set bridges the distance safely and reliably.The set includes two high-quality, double-insulated solar cables: one red cable for the positive terminal (+) and one black cable for the negative terminal (-). Both ends are professionally pre-assembled with MC4-compatible connectors and sockets. Due to the considerable length of 35 metres (70 metres total circuit), this set is primarily designed for systems with high string voltage in order to keep the percentage cable losses within an acceptable range.Highlights at a glanceMaximum range: With 35 metres length per cable, you can also implement complex installation scenarios far away from the house connection or main meter.Plug & Play installation: The cables are pre-assembled with MC4-compatible connectors on both sides, so no special crimping tools are required.Secure identification: The clear colour coding in red (+) and black (-) effectively prevents dangerous polarity confusion over this long cable run.Weatherproof & durable: The special sheath made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.IP67 protection class: The plug connections are absolutely dust-tight when plugged in and are protected against temporary immersion (e.g. in heavy rain or puddles).High-quality conductor: Tinned electrolytic copper ensures maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 35-metre extension is intended for specific scenarios:Ground-mounted systemsIdeal for installing modules far away in the garden or in a field, where there is no shadow cast by buildings or tall trees.Outbuildings & agricultureConnecting remote garages, carports, sheds or stables with the main building.Indirect cable routingWhen cables cannot be laid directly, but must be routed around the whole house or through extensive empty conduit systems.Installation & safety instructionsVoltage drop (Important!)At a length of 35 metres, the total circuit is 70 metres. For grid-connected systems with high string voltage (> 100V), 4mm² is acceptable. For 12V or 24V off-grid systems, this cable is not suitable due to the massive voltage loss; in this case 10mm² or 16mm² cross-sections must be used.Laying in the groundAlthough the cable is weatherproof, it is not protected against mechanical influences (spade cuts, rodents). When laying underground, you must always use a protective conduit (e.g. flexible conduit or cable protection pipe).Avoid induction & heatNever coil excess cable into a tight spool while current is flowing, as this can result in induction and heat build-up. Lay excess cable in wide loops ("meanders"). Features ModelSolar extension cable set (35m) Conductor cross-section**4.0 mm²** Cable length**35.0 metres** (per colour) Rated voltageUp to 1500V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine-stranded) Temperature range-40°C to +120°C Protection classProtection class II (double insulation) Special featureUV & ozone resistant, halogen-free  FAQs on the 35m solar extension cableIs 4mm² really still sufficient for a length of 35 metres?Technically safe for high-voltage systems, borderline for maximum efficiency. With a typical balcony power station (approx. 40V module voltage, 10A current), you have a voltage drop of approx. 3 volts at 35m. This corresponds to a power loss of around 7.5%. This is technically safe, but no longer optimal. Those who want to optimise yield should definitely upgrade to 6mm² cable for this extreme length.Will the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The connectors used comply with the worldwide MC4 standard used in almost all modern solar modules and micro-inverters. They fit mechanically and electrically perfectly.Can I shorten the cable if necessary?Yes, but only with expertise. You can cut the cable to length. However, remember that you will need professional MC4 connectors and a special crimping tool for the new connection to ensure a permanently safe and watertight connection.

The solar extension cable set (40 metres, 4mm²) is the specialised solution for photovoltaic projects with extreme distances. If your solar modules need to be positioned in the sunniest spot on the property – e.g. at the end of a very large garden, on a far-away barn or in an open field – and the inverter is to remain centrally located in the building, this set bridges the distance safely and reliably.The set includes two high-quality, double-insulated solar cables: one red cable for the positive terminal (+) and one black cable for the negative terminal (−). Both ends are professionally pre-assembled with MC4-compatible connectors and sockets. Due to the considerable length of 40 metres (80 metres total run in the circuit), this set is primarily designed for systems with high string voltage, so that the percentage line losses remain within an acceptable range.Highlights at a glanceExtreme range: With 40 metres of cable per colour, you can establish far-off setups from the house connection or main distribution panel.Plug & play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Safe identification: The clear colour coding in red (+) and black (−) efficiently prevents dangerous polarity mistakes along this very long cable run.Weatherproof & durable: The special jacket made of crosslinked polyolefin is UV-resistant, ozone-resistant, and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: The connectors, when plugged together, are absolutely dust-tight and protected against temporary submersion (e.g. during heavy rain or puddle formation).High-quality conductor: Tinned electrolytic copper ensures maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 40-metre extension is intended for specific scenarios:Large ground-mounted systemsIdeal for positioning modules far away in the garden or a meadow, where no shadows are cast by buildings or tall trees.Outbuildings & agricultureConnecting distant garages, carports, sheds or barns with the main building.Indirect cable routingWhen cables cannot be laid directly but must be routed around the house or through widely branched conduit systems.Installation & safety instructionsVoltage drop (Important!)With a length of 40 metres, the total current path is 80 metres. For grid-connected systems with high string voltage (> 120V), 4mm² is still acceptable. For 12V or 24V off-grid systems, this cable is totally unsuitable due to the considerable voltage drop; you would need cross-sections of 16mm² or more.Laying in soilAlthough the cable is weatherproof, it is not protected against mechanical influences (spade blades, rodents). When laying in the ground, a protective pipe (e.g. flexible pipe or cable protection pipe) must be used.Avoid induction & heatNever coil surplus cable into a tight roll while current is flowing, as this can cause induction and heat build-up. Lay excess lengths in wide loops ("meanders"). Features ModelSolar extension cable set (40m) Conductor cross-section**4.0 mm²** Cable length**40.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range-40°C to +120°C (on the conductor) ApprovalsEN 50618 / H1Z2Z2-K Special featureHalogen-free & UV-resistant  FAQs on the 40m solar extension cableIs 4mm² really still sufficient at 40 metres in length?Technically safe for high-voltage systems, but critical for efficiency. With a typical balcony solar system (approx. 40V module voltage, 10A current) you experience a voltage drop of approx. 3.5 volts at 40m. This results in a power loss of around 8.5%. Technically safe, but not really recommended. If you want to optimise yield at this extreme length, you should definitely upgrade to 6mm² or even 10mm² cable.Will the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The connectors used comply with the worldwide MC4 standard, which is used in almost all modern solar modules and microinverters. They fit mechanically and electrically without any issues.Can I shorten the cable if necessary?Yes, but only with expertise. You can cut the cable. However, for the new connection you will need professional MC4 connectors and a special crimping tool to ensure a permanently safe and watertight connection.

The solar extension cable set (40 metres, 6mm²) is the specialised solution for photovoltaic projects with extreme distances. If your solar modules need to be positioned in the sunniest part of the property – for example, at the end of a very large garden or in a distant paddock – and the inverter is placed centrally in the building, this generous 6mm² cross-section provides the necessary capacity to effectively minimise power losses over the entire 40-metre distance.The set includes two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (−). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the massive cross-section, this set is particularly future-proof and ideal for modern high-performance modules, where standard cables (4mm²) would already show significant efficiency losses over this enormous distance.Highlights at a glanceOptimised for long distances: The 6mm² cross-section significantly reduces electrical resistance, which is crucial for a high energy yield over 40 metres (80m total route).Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tools are required.Safe identification: The clear colour coding in red (+) and black (−) effectively prevents dangerous polarity mix-ups when installing over long distances.Weatherproof & durable: The special jacket made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from −40°C to +90°C.IP67 protection: The connectors are absolutely dustproof and protected against temporary submersion (e.g. in heavy rainfall) when plugged in.High-quality conductor: Tinned electrolytic copper ensures maximum corrosion resistance and consistently excellent conductivity, even under adverse conditions.Areas of applicationThis 40-metre extension is designed for demanding long-distance connections:Large ground-mounted systemsIdeal for installing modules far away in the garden or in a meadow where there is no shadow cast by buildings.Outbuildings & agricultureConnecting distant garages, carports or stables to the main building or the central meter cupboard.Stand-alone systems (24V / 48V)The 6mm² cross-section over 40 metres is particularly important for battery systems to keep the charging voltage stable and losses low.Assembly & safety instructionsEfficiency over distanceWith a cable length of 40 metres, 6mm² provides a significant advantage over 4mm². The lower resistance ensures higher system voltage at the inverter and thus measurably higher yields over the years.Protection for underground installationAlthough the cable is weatherproof, if it is to be laid in the ground it must always be routed in a suitable protective conduit to protect it from mechanical impact and rodents.Correct latchingWhen connecting, make sure that the MC4 connectors engage audibly. This is the only way to ensure the connection is permanently watertight and safe against dangerous arcing. Features ModelSolar extension cable set (40m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**40.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (fine stranded) Temperature range−40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely low-loss & UV-resistant  FAQs on the solar extension cable 40m 6mm²Why is 6mm² at 40 metres better than 4mm²?Because of the lower voltage drop. Over a total length of 80 metres (out and back), the electrical resistance adds up. A 6mm² cable reduces this resistance by about a third compared to a 4mm² cable, which can mean several percent higher yield in typical balcony systems or module strings.Do the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The connectors used conform to the worldwide MC4 standard. They fit mechanically and electrically perfectly to almost all common solar modules and inverters.Can I shorten the cable if 40m is too long?Yes, with expertise. You can cut the cable to length. However, please note that you will need professional MC4 connectors and a special PV crimping tool to ensure a permanently secure connection for the new connection.

The solar extension cable set (45 metres, 6mm²) is the specialised solution for photovoltaic projects with extreme distances. If your solar modules need to be positioned in the sunniest part of the property – for example, at the end of a very large garden or on a distant barn – and the inverter is centrally located in the building, this generous cross-section of 6mm² provides the necessary capacity to effectively minimise power losses across the full 45-metre distance.The set contains two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (−). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Thanks to the substantial cross-section, this set is especially future-proof and ideal for modern high-performance modules, where standard cables (4mm²) would already show significant losses in efficiency over such an enormous distance.Highlights at a glanceOptimised for long distances: The 6mm² cross-section considerably reduces electrical resistance, which is crucial for high levels of energy yield at 45 metres (90m round-trip distance).Plug & Play installation: The cables are pre-assembled on both ends with MC4-compatible connectors, so no special crimping tools are required.Secure identification: The clear colour coding in red (+) and black (−) effectively prevents dangerous polarity mix-ups on this extremely long cable run.Weatherproof & durable: The special cross-linked polyolefin sheath is UV-resistant, ozone-resistant, and withstands extreme temperatures from −40°C to +90°C.IP67 protection rating: The connectors are absolutely dust-tight and protected against temporary immersion (e.g., during heavy rain) when plugged in.High-quality conductor: Tinned electrolytic copper provides maximum corrosion resistance and lasting excellent conductivity even under challenging conditions.Areas of applicationThis 45-metre extension is designed for demanding long-range links:Large open-area systemsIdeal for locating modules far away in a garden or meadow, where there is no shading from buildings.Annexe buildings & agricultureConnecting remote garages, carports or barns to the main building or central meter cabinet.Off-grid systems (24V / 48V)In particular for battery systems, the 6mm² cross-section over 45 metres is essential to maintain charging voltage stability and keep losses low.Assembly & safety informationEfficiency over distanceWith 45 metres of cable length, 6mm² offers a significant advantage over 4mm². Lower resistance results in higher system voltage at the inverter and thus measurably greater yield over the years.Protection when buriedAlthough the cable is weatherproof, if it is to be laid underground it must always be run in a suitable protective conduit to protect it from mechanical effects and rodents.Correct latchingWhen connecting, make sure the MC4 connectors click audibly into place. Only then will the connection be reliably waterproof and safe from dangerous arcing. Features ModelSolar extension cable set (45m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**45.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range−40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely low-loss & weather-resistant  FAQs about the solar extension cable 45m 6mm²Why is 6mm² at 45 metres better than 4mm²?Due to the lower voltage drop. Over a total distance of 90 metres (to and fro), the electrical resistance adds up. A 6mm² cable reduces this resistance by around a third compared to a 4mm² cable, which can mean several percent more yield for typical balcony power systems or module strings.Do the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The supplied connectors meet the global MC4 standard. They fit mechanically and electrically without issue to almost all standard solar modules and inverters.Can I shorten the cable if 45 metres is too long?Yes, with the right expertise. You may cut the cable. However, be aware that for the new connection you will need professional MC4 connectors and a special PV crimping tool to ensure a permanently safe connection.

The solar extension cable set (50 metres, 6mm²) is the ultimate range solution for photovoltaic projects with extreme distances. If your solar panels have to be installed in the sunniest spot on your property – such as at the end of a large paddock, on a remote barn or in an open field – and the inverter is centrally located in a building, this generous cross-section of 6mm² provides the necessary capacity to limit power losses over the enormous 50 metre route.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Due to the massive total length of 50 metres (100 metres total in the circuit), a cross-section of 6mm² is the absolute minimum technical recommendation to maintain the efficiency of your system.Highlights at a glanceMaximum range: With 50 metres of cable, you can implement extremely large-scale installation scenarios far from the house connection or main distribution board.Minimised resistance: The 6mm² cross-section is essential at this length to significantly reduce voltage drop compared to standard cables (4mm²).Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no specialist crimping tools are required.Safe identification: The clear colour coding in red (+) and black (-) effectively prevents dangerous polarity mix-ups over such extremely long runs.Weatherproof & durable: The special cross-linked polyolefin jacket is UV-resistant, resistant to ozone and can withstand extreme temperatures from -40°C to +90°C.IP67 protection: The connectors are absolutely dustproof when plugged in and protected against temporary immersion.Areas of applicationThis 50-metre extension is designed for specific long-distance connections:Large ground-mounted systemsIdeal for placing modules far away in a meadow or at the edge of the property where there is no shading from buildings or woodland edges.Agriculture & industryConnecting remote barns, stables or pumping stations to a central meter cabinet or inverter room.Off-grid systems (24V / 48V)For battery systems over a distance of 50m, a 6mm² cross-section is absolutely necessary to keep the charging voltage stable; for 12V systems, even with 6mm², this distance would already be critical.Installation & Safety InstructionsObserve voltage dropAt 50 metres length, the total power path is 100 metres. For grid-tied systems with high string voltage (> 200V), 6mm² is a very good choice. For lower voltages (e.g. only one 40V module), the percentage loss over this distance, even with 6mm², is already noticeable.Protection for underground installationThe cable is weather-resistant, but not protected against mechanical influences. You must use a suitable protective conduit (e.g. cable protection tube) for underground installation to prevent damage from rodents or excavation work.Avoid induction & heatNever coil excess cable tightly while current is flowing. This can lead to induction and dangerous heat build-up. Lay excess lengths in wide loops. Features ModelSolar extension cable set (50m / 6mm²) Conductor cross-section**6.0 mm²** Cable length**50.0 metres** (per colour) Rated voltageUp to 1500 V DC Connector type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (at conductor) StandardTÜV / EN 50618 (H1Z2Z2-K) Special featureExtremely low-loss & weather-resistant FAQs about the solar extension cable 50m 6mm²Is 6mm² really sufficient for 50 metres length?Yes, for high-voltage systems; borderline for balcony PV. With a typical balcony PV system (40V, 10A), you lose around 3 volts (7.5% output) over 50m with a 6mm² cable. This is technically safe but already a compromise in energy. For maximum yield at this length, we recommend wiring the modules in series to increase the voltage and reduce the percentage loss.Will the connectors fit my inverter from Growatt, Deye or Victron?Yes. The connectors used comply with the worldwide MC4 standard. They fit both mechanically and electrically with almost all standard solar modules and inverters.Can I shorten the cable if needed?Yes, but only with expertise. You can cut the cable to length. However, please note that you will need professional MC4 connectors and a suitable PV crimping tool to ensure a permanently safe connection.

The solar extension cable set (45 metres, 4mm²) is the specialised solution for photovoltaic projects with extreme distances. If your solar modules need to be located at the sunniest spot on the property – such as at the end of a very large garden, on a distant barn or in an open field – and the inverter is to remain centrally inside the house, this set allows you to safely and reliably bridge the distance.The set includes two high-quality, double-insulated solar cables: one red cable for the positive pole (+) and one black cable for the negative pole (−). Both ends are professionally pre-assembled with MC4-compatible connectors and sockets. Due to the considerable length of 45 metres (90 metres total current path), this set is primarily intended for systems with high string voltage, to keep percentage line losses within reasonable limits.Highlights at a glanceExtreme range: With a length of 45 metres per cable, you can also realise complex installation scenarios far from the house connection or main distribution board.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: Clear colour coding in red (+) and black (−) effectively prevents dangerous mix-ups of polarity during very long cable runs.Weatherproof & Durable: The special sheath made of cross-linked polyolefin is UV-resistant, ozone-resistant and can withstand extreme temperatures from −40°C to +90°C.Protection rating IP67: The connectors are absolutely dust-tight when plugged in and protected against temporary submersion (e.g. during heavy rain or puddle formation).High quality conductor: Tinned electrolytic copper provides maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 45-metre extension is intended for specific scenarios:Large ground-mounted systemsIdeal for placing modules far away in the garden or on a field, where there is no shading from buildings or tall trees.Outbuildings & AgricultureConnecting distant garages, carports, sheds or barns to the main building.Indirect cable routingWhen cables cannot be laid directly but instead have to be routed all around the house or through widely branched empty conduit systems.Installation & safety instructionsVoltage drop (Important!)With a length of 45 metres, the total current path is 90 metres. For grid-connected systems with high string voltage (> 150V), 4mm² is still acceptable. For 12V or 24V stand-alone systems, this cable is absolutely unsuitable due to the massive voltage loss; here you would have to use cross-sections of 16mm² or more.Laying in the groundAlthough the cable is weatherproof, it is not protected against mechanical influences (spade cuts, rodents). When laying underground, always use a protective conduit (e.g. flexible conduit or cable protection pipe).Avoid induction & heatNever coil excess cable into a tight spool while current is flowing, as this can lead to induction and heat build-up. Lay excess cable in wide loops ("meanders"). Features ModelSolar extension cable set (45m) Conductor cross-section**4.0 mm²** Cable length**45.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureHalogen-free, UV & ozone resistant FAQs about the solar extension cable 45mIs 4mm² really still sufficient at a length of 45 metres?Technically safe for high-voltage systems, but critical for efficiency. With a typical plug-in solar system (approx. 40V module voltage, 10A current), you have a voltage drop of approx. 4 volts at 45m. This means around 10% power loss. This is technically safe, but no longer recommended. To optimise the yield with this extreme length, you should definitely upgrade to 6mm² or even 10mm² cable.Do the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The connectors used conform to the global MC4 standard, which is used with almost all modern solar modules and micro inverters. They fit perfectly in terms of both mechanics and electrics.Can I shorten the cable if necessary?Yes, but only with expertise. You can cut the cable to size. Please note, however, that for the new connection you'll need professional MC4 connectors and a special crimping tool to ensure a permanently secure and watertight connection.

The Solar extension cable set (50 metres, 4mm²) is the ultimate range solution for photovoltaic projects with extreme distances. If your solar modules need to be located in the sunniest place on the property – for example at the end of a spacious garden, in a remote paddock or on a remote outbuilding – and the inverter needs to remain centrally in the house, you can bridge the distance safely and reliably with this set.The set contains two high-quality, double-insulated solar cables: a red cable for the positive pole (+) and a black cable for the negative pole (-). Both ends are professionally pre-assembled with MC4-compatible plugs and sockets. Due to the massive length of 50 metres (100 metres total in the circuit), this set is designed exclusively for systems with very high string voltage to keep percentage line losses within acceptable limits.Highlights at a glanceMaximum range: With a length of 50 metres per cable, you can also realise extremely far-reaching installation scenarios far from the house connection.Plug & Play installation: The cables are pre-assembled on both sides with MC4-compatible connectors, so no special crimping tool is required.Secure identification: The clear colour coding in red (+) and black (-) effectively prevents dangerous polarity confusion over this extremely long laying distance.Weatherproof & durable: The special sheath made of cross-linked polyolefin is UV-resistant, ozone-resistant and withstands extreme temperatures from -40°C to +90°C.Protection class IP67: The plug connections are absolutely dust-tight and protected against temporary submersion (e.g. in heavy rain or puddles) when plugged in.High-quality conductor: Tin-plated electrolytic copper ensures maximum corrosion resistance and permanently excellent conductivity.Areas of applicationThis 50-metre extension is intended for specific scenarios:Large open-space systemsIdeal for setting up modules far away on a meadow or at the edge of a property where there is no shade from buildings or forest edges.Agriculture & outbuildingsConnecting distant barns, stables or pumping stations to the main building.Indirect cable routingWhen cables cannot be laid directly, but must be routed over long detours around obstacles or through long empty conduit systems.Assembly & safety instructionsVoltage drop (Extremely important!)At a length of 50 metres, the total current path is 100 metres. For grid-connected systems with very high string voltage (> 200V), 4mm² is technically possible. For 12V or 24V stand-alone systems, this cable is absolutely unsuitable due to the massive voltage drop; your consumers would hardly get any energy here.Laying undergroundAlthough the cable is weatherproof, it is not protected against mechanical influences (spade cuts, rodents). When laying underground, you must use a high-quality protective conduit (e.g. cable protection pipe).Avoid induction & heatNever coil excess cable tightly while current is flowing, as this can cause induction and heat development. Lay excess lengths in large loops. Features ModelSolar extension cable set (50m) Conductor cross-section**4.0 mm²** Cable length**50.0 metres** (per colour) Rated voltageUp to 1500 V DC Plug type**MC4 compatible** (IP67) Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) StandardisationTÜV / EN 50618 (H1Z2Z2-K) Special featureUV- & ozone-resistant, halogen-free  FAQs about the solar extension cable 50mDoes 4mm² still make sense at 50 metres in length?For standard balcony power plants rather no. For a typical balcony power plant (approx. 40V module voltage, 10A current), you have a voltage drop of approx. 4.5 volts at 50m. This corresponds to a power loss of around 11-12%. This is technically safe, but energetically very inefficient. At this length, we strongly recommend switching to 6mm² or better 10mm² cable.Do the connectors fit my inverter from Hoymiles, Deye or Growatt?Yes. The built-in connectors comply with the worldwide MC4 standard, which is used in almost all modern solar modules and microinverters. They fit perfectly both mechanically and electrically.Can I shorten the cable if necessary?Yes, but only with expertise. You can cut the cable. However, please note that for the new connection you will need professional MC4 connectors and a special crimping tool to ensure a permanently reliable and watertight connection.

The SOLR6100 solar cable (100 metres, 6mm²) in red is the professional solution for photovoltaic installations where maximum efficiency and minimum resistance are paramount. With a length of 100 metres per roll and a reinforced cross-section of 6mm², this cable is ideal for large rooftop installations, ground-mounted projects, or systems with high current ratings. The red marking allows standard-compliant identification of the positive pole (+) and ensures clear cabling.Certified according to the international standard IEC 62930, this cable provides the highest safety for modern PV systems with voltages up to 1500V DC. The larger cross-section minimises voltage losses even over long distances and is ideal for high-performance module generations delivering high currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section greatly reduces electrical resistance and ensures higher yield compared to standard cables.Certified safety: Conforms to IEC 62930 (H1Z2Z2-K) standard for use in photovoltaic systems up to 1500V DC.High coverage: 100 metres in one piece allow for individual cuts for custom string connections without unnecessary junctions.Extremely durable: High quality XLPO double insulation is UV-resistant, ozone-resistant and flame-retardant for a service life of over 25 years.Corrosion-protected conductor: Fine stranded, tinned copper provides consistently optimal conductivity and protection against oxidation in humid environments.Wide temperature range: Safe operation under extreme weather conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLR6100 is the first choice for demanding PV projects:Large rooftop systems & PV parksEfficient string cabling and connecting distant module fields to the central inverter.High-performance balcony systemsIdeal for systems with modern modules (500Wp+), to transport high currents without loss.Battery storage & off-grid systemsPerfect for 24V or 48V systems where minimal voltage drops are crucial for charging efficiency.Installation & safety instructionsProfessional connectionUse only MC4 connectors explicitly approved for 6mm² cable with this cross-section and a high-quality crimping tool.Mechanical protectionWhen routing on the roof or through walls, use corrugated conduits or cable ducting to protect the insulation from mechanical abrasion and rodent damage.Parallel cable routingRun positive (red) and negative (black) cables as parallel and close as possible together, to minimise electromagnetic interference (induction loops). Features Model / SKU**SOLR6100** Conductor cross-section**6.0 mm²** Form of supply**100 metre roll** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** Special featureHalogen-free, UV & ozone resistant  FAQs on the red solar cable 100m 6mm²Why should I choose 6mm² instead of 4mm²?For higher yield and future-proofing. Especially with cable lengths over 15–20 metres or when using modules with high current (Isc over 13A), the voltage drop with 6mm² is noticeably lower. This means that more energy reaches the inverter and the cable remains cooler under high load.Can the cable be laid directly in the ground?Only in a protective conduit. Although the insulation is very robust, the cable is not designed for direct burial without protection. In suitable cable protection conduit, however, laying in the ground is no problem.Is the cable resistant to chemicals?Yes. The XLPO insulation is resistant to acids, alkalis, and ammonia. This makes it especially suitable for installations in agriculture (barns) or in areas affected by industrial pollution.

The solar cable SOLS6100 (100 metres, 6mm²) in black is the professional solution for photovoltaic installations where maximum efficiency and minimal resistance are paramount. With a length of 100 metres on a reel and a reinforced cross-section of 6mm², this cable is excellent for large roof systems, open-area projects or systems with high currents. The black identification enables standard-compliant identification of the negative pole (-) and ensures clearly arranged cabling.Certified in accordance with the international standard IEC 62930, this cable offers maximum safety for modern PV systems with voltages of up to 1500V DC. The larger cross-section minimises voltage losses even over long distances and is ideal for high-performance module generations delivering high currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section significantly reduces the electrical resistance and provides more yield compared to standard cables.Certified safety: Complies with IEC 62930 (H1Z2Z2-K) standard for use in photovoltaic systems up to 1500V DC.Long range: 100 metres in one piece enable custom cuts for tailor-made string connections without unnecessary separation points.Extremely resistant: The high-quality XLPO double insulation is UV-resistant, ozone-resistant and flame-retardant for a lifespan of more than 25 years.Corrosion-protected conductor: Fine-stranded, tinned copper offers permanently optimum conductivity and protects against oxidation in a damp environment.Wide temperature range: Safe operation in extreme weather conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLS6100 is the number one choice for demanding PV projects:Large roof systems & PV parksEfficient string cabling and connection of distant module fields to the central inverter.High-performance balcony power plantsIdeal for systems with modern modules (500Wp+), to ensure the loss-free transport of high currents.Battery storage & stand-alone systemsPerfect for 24V or 48V systems where low voltage drops are crucial for charging efficiency.Assembly & safety instructionsProfessional connectionsFor this cross-section, use only MC4 connectors that are explicitly approved for 6mm² cable, and use high-quality crimping pliers.Mechanical protectionWhen laying on the roof or through walls, use corrugated ducts or cable ducts to protect the insulation from mechanical abrasion and rodent bites.Parallel cable routingRoute the black negative cable as parallel and close as possible to the red positive cable to minimise electromagnetic interference fields (induction loops). Features Model / SKU**SOLS6100** Conductor cross-section**6.0 mm²** Delivery form**100 metre reel** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** Special featureHalogen-free, UV- & ozone-resistant  FAQs about solar cable black 100m 6mm²Why should I choose 6mm² instead of 4mm²?For more yield and future-proofing.Especially for cable lengths above 15–20 metres or when using modules with high current (Isc above 13A), voltage drop is noticeably lower with 6mm². This means more energy reaches the inverter and the cable stays cooler under high load.Can the cable be laid directly in the ground?Only in protective conduit.Although the insulation is very robust, the cable is not designed for direct burial without protection. Installation in a suitable cable conduit in the ground, however, is no problem.Is the cable resistant to chemicals?Yes.The XLPO insulation is resistant to acids, alkalis and ammonia. This makes it particularly suitable for agricultural (stables) or industrially impacted areas.

The SOLS4100 solar cable (100 metres, 4mm²) in black is the ideal cable by the metre for extensive photovoltaic projects and professional installations. With a generous length of 100 metres on the reel, it offers maximum flexibility when cabling roof systems, ground-mounted projects or larger stand-alone installations. The black marking serves for clear identification of the negative pole (-), which significantly increases safety and clarity during installation.Manufactured according to the strict international standard IEC 62930, this cable meets the highest quality requirements for long-term use in modern PV systems up to 1500V DC. Thanks to the high-quality cross-section of 4mm² and the special double insulation, it is ideally equipped to transport the energy produced by your solar modules safely and with low losses for decades.Highlights at a glanceCertified safety: Complies with the IEC 62930 standard (H1Z2Z2-K) for use in photovoltaic DC systems up to 1500V DC.High reach: 100 metres in one piece allow individual cuts for customised string connections without unnecessary intermediate connections.Clear polarity: The black outer sheath ensures clear marking of the negative conductor and prevents errors during installation.Weatherproof & extremely durable: Specially designed for permanent outdoor use – UV-resistant, ozone-proof and resistant to embrittlement due to intense sunlight.Optimal conductivity: The finely stranded conductor made of tinned copper ensures permanently low contact resistances and provides effective protection against corrosion.Wide temperature range: Reliable operation under extreme weather conditions from -40°C to +90°C (maximum conductor temperature up to +120°C).Areas of applicationThe SOLS4100 is the first choice for versatile installation scenarios:Roof installations & PV parksCreation of customised string connections from the module array to the inverter or collector box.Off-grid systems & motorhomesFlexible wiring of off-grid systems where custom cable lengths are required for a neat installation.Plant constructionIdeal basic component for installers to assemble custom connection cables with MC4 connectors.Mounting & safety instructionsProfessional assemblyAs it is sold by the metre, we recommend using high-quality MC4 connectors and a professional crimping tool for solar cables for installation.Avoidance of induction loopsRoute the black negative conductor as parallel and close as possible to the red positive conductor to minimise electromagnetic interference fields.Mechanical protectionWhen running on the roof or through walls, use corrugated tubes or cable ducts to protect the insulation from mechanical abrasion. Features Model / SKU**SOLS4100** Conductor cross-section**4.0 mm²** Delivery form**100 metre roll** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** FeaturesHalogen-free, UV-resistant & short-circuit-proof  FAQs about the solar cable black 100m 4mm²Is the cable suitable for direct burial?Only in protective conduit. The cable is suitable for installation in pipes and ducts in the ground, as long as it is ensured that it does not lie permanently in water. Direct installation without protective conduit in the ground is not recommended.Why is the conductor tinned?For protection against corrosion. The tinning of the copper wires prevents oxidation of the copper, especially in humid environments or in contact with salty air. This ensures consistently high conductivity throughout the service life of the system.Can I lay this cable indoors as well?Yes. Thanks to the flame-retardant and halogen-free properties of the XLPO insulation, the SOLS4100 can be safely installed in buildings to deliver the energy to the inverter room.

The SOLR4100 solar cable (100 metres, 4mm²) in red is the ideal cable by the metre for extensive photovoltaic projects and professional installations. With a generous length of 100 metres on the roll, it offers maximum flexibility when cabling roof systems, ground-mounted projects or larger stand-alone systems. The red marking serves for clear identification of the positive pole (+), which greatly increases safety and clarity during installation.The cable has been specially developed for the extreme demands of outdoor use. Thanks to the high-quality cross-section of 4mm² and the special double insulation, it is perfectly equipped to transport the energy produced by your solar modules safely and with minimal loss over decades.Highlights at a glanceHigh range: 100 metres in one piece allow individual cuts without unnecessary intermediate connections or waste.Clear polarity: The red outer sheath ensures clear marking of the positive conductor and prevents errors during installation.Robust double insulation: The cable features a flame-retardant and halogen-free sheath that provides optimum protection against mechanical stress.Weatherproof & extremely durable: Specially designed for permanent outdoor use – UV-resistant, ozone-resistant and resistant to acids and alkalis.Wide temperature range: Reliable operation in extreme weather conditions from -40°C to +90°C (maximum conductor temperature up to +120°C).Optimum conductivity: The finely stranded conductor made of tinned copper ensures permanently low transition resistances and offers effective corrosion protection.Areas of applicationThe SOLR4100 is the first choice for versatile installation scenarios:Roof systems & PV parksCreation of individual string connections from module field to inverter or collection box.Off-grid systems & motorhomesFlexible wiring of off-grid systems where accurately fitting cable lengths are required for a neat installation.Plant constructionIdeal base component for installers to assemble individual connecting cables with MC4 connectors.Assembly & safety instructionsProfessional assemblyBecause this is cable by the metre without connectors, we recommend using high-quality MC4 connectors and professional crimping pliers for solar cables when connecting.Protection from rodentsWhen laying in areas at risk from rodents (e.g. barns or soil) the cable should also be run inside a suitable protective conduit.Standard-compliant routingEnsure the cable is laid without tension and secured with UV-resistant cable ties to avoid chafe marks caused by wind movement. Features Model / SKU**SOLR4100** Conductor cross-section**4.0 mm²** Delivery form**100 metre roll** ColourRed (positive pole marking) Rated voltageAC: 1.0 kV / DC: 1.5 kV (max.) Conductor materialCopper, tinned (class 5) Temperature range-40°C to +120°C (max. conductor temp.) Certification**TÜV / EN 50618 (H1Z2Z2-K)** FeaturesUV, ozone, acid & alkali resistant FAQs about the solar cable red 100m 4mm²Is the cable suitable for direct burial?Conditionally. The cable is suitable for laying in pipes and ducts in the ground as long as it is ensured that it is not permanently lying in water. Direct laying in earth without a protective conduit is not recommended.Can I also use this cable for 1500V systems?Yes. As an H1Z2Z2-K certified cable, it is designed for a maximum system voltage of 1500V DC and thus meets the latest standards for photovoltaic installations.Why is the conductor tinned?To protect against corrosion. The tinning of the copper wires prevents oxidation of the copper, especially in damp environments or in contact with salty air. This guarantees consistently high conductivity over the entire lifetime of the system (25+ years).

The SOLR425 solar cable (25 metres, 4mm²) in red is the perfect choice for flexible cabling of your photovoltaic system. With a length of 25 metres, this cable is ideal for medium-sized projects, such as connecting module strings to the inverter or installing balcony power stations with slightly longer routes. The red colour serves as a standard-compliant marking of the positive pole (+), making the installation clear and safe.Manufactured in accordance with the strict standard IEC 62930, this cable fulfils the highest safety standards for permanent use in modern PV systems. The combination of high-quality tinned copper conductor and robust double insulation guarantees efficient energy transmission and maximum service life, even under demanding environmental conditions.Highlights at a glanceCertified safety: Complies with the international standard IEC 62930 for solar cables, which guarantees top quality and fire protection.Optimal length: 25 metres allow for custom cuts for bespoke connections without unnecessary joints.Clear identification: The red outer sheath ensures clear identification of the positive lead and prevents confusion during installation.Extremely robust: The double insulation made from cross-linked special polymer is UV-resistant, ozone-resistant and resistant to weathering.Durable conductor: Tinned electrolytic copper provides effective protection against corrosion and ensures permanently low contact resistances.High temperature resistance: Safe to use in a range from -40°C to +90°C, conductor temperatures of up to +120°C are permitted for short periods.Areas of applicationThe SOLR425 is versatile for private and commercial PV projects:Home & rooftop systemsIdeal for string cabling and connection to the charge controller or inverter over medium distances.Balcony power stationsPerfectly suited for connecting the solar modules to the microinverter when it is mounted indoors or in a remote location.Motorhomes & MarineReliable wiring for solar panels on vehicle roofs or boats, where resistance to vibrations and moisture is required.Installation & safety instructionsProfessional crimpingAs this is cut by the metre, only high-quality MC4 connectors should be used for connection. Ensure gas-tight crimping with a suitable crimping tool.Mechanical protectionLay the cable on sharp edges (e.g. on profile rails) always in such a way that the insulation is not damaged. Use edge protection or corrugated pipes for this.Observe bending radiiAvoid bends that are too tight in the cable to prevent damage to the fine stranded copper conductors and to maintain the integrity of the insulation. Features Model / SKU**SOLR425** Conductor cross-section**4.0 mm²** Form of supply**25 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (fine stranded) Temperature range-40°C to +90°C (ambient) Standardisation**IEC 62930 / EN 50618** Fire protectionFlame-retardant & halogen-free  FAQs on the red 25m 4mm² solar cableWhat does certification to IEC 62930 mean?Tested quality for PV systems. This standard defines the requirements for halogen-free, low-smoke and insulated cables for photovoltaic systems. It ensures that the cable is specifically designed for the high DC voltage and UV exposure in outdoor use.Can I lay the cable indoors too?Yes. Thanks to the flame-retardant and halogen-free properties of the insulation, the SOLR425 can be installed indoors without hesitation to carry energy from the roof to the inverter in the basement or technical room.Why should I choose 4mm² instead of 6mm²?Cost-effectiveness over short distances. With a length of 25 metres, the voltage drop at 4mm² is negligibly low in most standard PV applications. The cable is easier to install and still offers high current carrying capacity for modern modules.

The SOLR450 solar cable (50 metres, 4mm²) in red is the ideal cable by the metre for photovoltaic projects that require flexible and secure cabling over medium distances. With a length of 50 metres, this reel offers sufficient range for string cabling on rooftops or for connecting module fields to the inverter. The red colouring ensures standard-compliant identification of the positive pole (+), making installation clear and minimising connection errors.Certified according to the international standard IEC 62930, this cable meets the highest requirements for safety and durability. It is specially designed for harsh outdoor conditions and, thanks to its high-quality material composition, ensures efficient energy transmission over the entire service life of your solar system.Highlights at a glanceCertified standard: Complies with IEC 62930 (H1Z2Z2-K), guaranteeing maximum suitability for photovoltaic direct current systems up to 1500V.Generous range: 50 metres in one piece enable continuous installation without additional plug connections between module and technical room.Clear polarity: The red outer insulation ensures a clear visual separation of the positive conductor, increasing safety during installation and maintenance.Weather & UV resistant: The high-quality XLPO double insulation provides long-lasting protection against embrittlement caused by sunlight, ozone and severe weather.Optimum conductivity: The finely stranded conductor made of tinned copper offers excellent corrosion protection and consistently low contact resistance.High thermal load capacity: Reliable operation in a wide temperature range from -40°C to +90°C.Areas of applicationThe SOLR450 is the ideal choice for a variety of installation scenarios:Single-family homes & roof systemsPerfect for connecting solar modules to the inverter if installed in the basement or utility room.Balcony solar systems & garden systemsIdeal for installations where a greater distance needs to be covered between the panels and the feed-in point.Mobile solar systemsUsed in independent systems for tiny houses or larger motorhomes where certified industrial quality is valued.Assembly & safety instructionsProfessional connectionUse only high-quality MC4 connectors when assembling and ensure precise crimping using a specialised solar crimping tool.Mechanical fixationSecure the cable at regular intervals with UV-resistant cable ties to minimise mechanical stresses caused by wind or its own weight.Avoidance of standing waterLay the cable so that it is not permanently in standing water (e.g. in depressions on flat roofs) to maximise protection of the insulation. Features Model / SKU**SOLR450** Conductor cross-section**4.0 mm²** Delivery form**50 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +90°C (ambient) Certificates**IEC 62930 / EN 50618 (H1Z2Z2-K)** Special featureHalogen-free & short-circuit proof  FAQs about solar cable red 50m 4mm²Why is the IEC 62930 certification important?It guarantees longevity in PV systems. This standard ensures that the cable is halogen-free, flame-retardant and specially designed to withstand stresses from high DC voltages and UV light. This sets it apart significantly from conventional installation cables.Is 4mm² sufficient for a 50 metre cable?Yes, for moderate currents. In a typical module string with high voltages, voltage drop at 50 metres and 4mm² is generally completely negligible. With systems with very low voltages (e.g. 12V), however, the voltage drop should be checked in advance.Is the cable resistant to acids and alkalis?Yes. The XLPO insulation provides good resistance to chemical influences, which is particularly advantageous for installations near industrial areas or in agriculture (ammonia exposure).

The solar cable SOLR475 (75 metres, 4mm²) in red is a high-quality solution for cabling photovoltaic systems over long distances. With a length of 75 metres, this reel offers maximum flexibility for string cabling on extensive roofs or when connecting module arrays to the inverter in larger buildings. The red colour is used for standard-compliant marking of the positive pole (+), which makes the installation clear and increases safety during installation.Certified according to the international standard IEC 62930, the SOLR475 fulfils the strictest quality requirements for long-term use under extreme conditions. The combination of a finely stranded, tinned copper conductor and the robust XLPO double insulation ensures efficient energy transmission and protects the cable from environmental influences for decades.Highlights at a glanceCertified industrial quality: Complies with the IEC 62930 standard (H1Z2Z2-K) and is therefore approved for system voltages up to 1500V DC.Optimum project length: 75 metres in one piece enable uninterrupted installation even with complex cable routes without unnecessary coupling points.Secure identification: The red outer sheath ensures clear visual identification of the positive cable in accordance with current installation standards.Maximum resistance: The UV and ozone-resistant XLPO double insulation prevents premature ageing due to solar radiation and weathering.Corrosion-protected conductor: Tinned electrolytic copper guarantees permanently low contact resistance and protects against oxidation, even in damp environments.Extreme temperature range: Safe use from -40°C to +90°C (maximum conductor temperature up to +120°C).Areas of applicationThe SOLR475 is the ideal choice for demanding installation scenarios:Larger roof systemsPerfect for connecting the solar modules to the inverter if it is installed over several floors or in a remote technical room.Commercial PV projectsIdeal for string cabling in larger systems where high reliability and standard-compliant design are required.Island & hybrid systemsUsed in self-sufficient power supplies for remote buildings or farms.Assembly & safety instructionsProfessional assemblyOnly use high-quality MC4 connectors to complete the cable. Gas-tight crimping with special solar pliers is essential for long-term safety.Protection against mechanical damageAlways lay the cable in protective conduits at wall penetrations or sharp roof edges to protect the insulation from mechanical abrasion.Avoidance of cable loopsMake sure that the cable is laid in such a way that no large induction loops are created (positive and negative cables should be routed as close together as possible) in order to improve the EMC compatibility of the system. Features Model / SKU**SOLR475** Conductor cross-section**4.0 mm²** Delivery form**75 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (class 5) Temperature range-40°C to +90°C (ambient) Standardisation**IEC 62930 / EN 50618** Special featureAcid & alkali resistant, halogen-free FAQs about solar cable red 75m 4mm²Why is 4mm² often sufficient for 75 metres?Due to the high string voltage. In modern PV systems, modules are often connected in series, which increases the voltage and keeps the current (amperes) relatively low. At high voltages, the percentage power loss with 4mm² is usually very low, even over 75 metres.Can the cable also be permanently laid outdoors?Yes. The cable is specially certified for outdoor installation. It is resistant to ammonia (important in agriculture), ozone and intensive UV radiation.What is the advantage over conventional rubber cables?The chemical cross-linking of the insulation. The XLPO insulation (cross-linked polyolefin) does not melt in the heat and does not become brittle in winter. It is also flame-retardant and halogen-free, which minimises smoke development in the event of a fire.

The SOLR625 solar cable (25 metres, 6mm²) in red is the ideal solution for photovoltaic installations that require a high current carrying capacity and minimal energy losses. With a length of 25 metres and a reinforced cross-section of 6mm², this cable offers the perfect balance between flexibility and performance – whether for string cabling on the roof or the connection of powerful balcony power plants. The red colour is used for the standard-compliant identification of the positive pole (+).Manufactured according to the international standard IEC 62930, this cable meets the strictest requirements for safety and durability in modern PV systems up to 1500V DC. The generous cross-section ensures that even with modules with high output currents, heat development is minimised and the efficiency of your system is maximised.Highlights at a glanceCertified safety: Complies with IEC 62930 (H1Z2Z2-K) for permanent use in photovoltaic DC systems up to 1500V.High efficiency: The 6mm² cross-section minimises electrical resistance and significantly reduces voltage drops compared to standard cables.Optimal project length: 25 metres enable tailor-made sections for medium distances without unnecessary interfaces or plug-in connections.Weather & UV resistant: The high-quality XLPO double insulation protects the cable against embrittlement from the sun, ozone and extreme weather conditions for decades.Corrosion-protected conductor: Fine-stranded, tinned copper ensures consistently optimum conductivity and offers effective protection against oxidation in humid environments.Extreme temperature range: Reliable operation under even the most adverse conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLR625 is versatile for demanding PV projects:Modern roof systemsIdeal for connecting high-performance modules (500Wp+) to the inverter to transport high currents without loss.Balcony power plants & stand-alone systemsPerfect when the inverter or charge controller is installed a little further away and every watt of power is to be maintained.Motorhomes & marineRobust cabling for self-sufficient systems where vibrations, humidity and high loads are a factor.Assembly & safety instructionsProfessional assemblyUse only MC4 connectors that are explicitly approved for 6mm² cable for this cross-section. A gas-tight crimp is essential for long-term safety.Observe bending radiiDespite the high flexibility of the fine stranded conductors, the cable should not be bent below the minimum permissible bending radius to preserve the insulation.Mechanical protectionFor entries or sharp edges, use protective tubes or edge protection profiles to permanently ensure the integrity of the double insulation. Features Model / SKU**SOLR625** Conductor cross-section**6.0 mm²** Delivery form**25 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (at conductor) Standardisation**IEC 62930 / EN 50618** FeaturesHalogen-free, flame-retardant, UV-resistant  FAQs about the solar cable red 25m 6mm²Is 6mm² necessary for 25 metres in length?It is recommended. Especially for modern modules delivering currents of 13A to 18A, 6mm² offers significantly more protection against heating and reduces the voltage drop. It is a future-proof option for maximum yields.Can the cable be laid indoors?Yes. Thanks to the flame-retardant and halogen-free properties of the XLPO insulation, the SOLR625 can be safely installed in buildings to carry energy from the roof to the technical room.Does the cable fit standard MC4 connectors?Only in suitable 6mm² variants. There are MC4 connectors for various cross-section ranges. Make sure to use connectors designed for 4–6mm² so that strain relief and sealing work correctly.

The Solar cable SOLR650 (50 metres, 6mm²) in red is the ideal cable by the metre for photovoltaic projects that place the highest demands on efficiency and durability. With a length of 50 metres and a reinforced cross-section of 6mm², this cable offers the perfect reserves for string cabling on rooftops or connecting distant module arrays. The red colouring is used for standard-compliant identification of the positive pole (+), which makes installation clear and minimises the risk of polarity reversal.Certified according to the international standard IEC 62930, this cable fulfils the strictest requirements for use in modern PV systems up to 1500V DC. The generous cross-section ensures that the voltage drop is minimised and the overall yield of your system is maximised, even with the high currents of modern high-performance modules.Highlights at a glanceMaximum efficiency: The cross-section of 6mm² massively reduces the electrical resistance and ensures minimal voltage drop, especially over distances of 50 metres.Certified safety: Complies with the IEC 62930 standard (H1Z2Z2-K) for permanent use in photovoltaic direct current systems up to 1500V.Optimum project length: 50 metres in one piece enable uninterrupted installation without additional plug connections between the module array and inverter.Weather & UV resistant: The high-quality XLPO double insulation protects the cable against embrittlement caused by sun, ozone and extreme weather conditions for decades.Corrosion-protected conductor: Fine-stranded, tinned copper offers the best long-term conductivity and provides effective protection against oxidation, even in damp or salty environments.High thermal load capacity: Reliable operation in a wide temperature range from -40°C to +90°C.Areas of applicationThe SOLR650 is the ideal choice for demanding installation scenarios:Large roof systemsPerfect for connecting the solar modules to the inverter if it is installed in the basement or in a remote technical room.Powerful balcony power stationsIdeal for systems with modern modules (500Wp+) to transport the high currents safely and without losses.Island & battery storageIdeally suited for 24V or 48V systems where low voltage drops are crucial for optimum battery charging.Assembly & safety instructionsProfessional connectionOnly use high-quality MC4 connectors that are approved for 6mm² cross-sections. Precise crimping with a special solar crimping tool is essential.Mechanical fixationFasten the cable at regular intervals with UV-resistant cable ties to avoid mechanical stress caused by wind or dead weight on the connections.Avoidance of induction loopsRun positive (red) and negative (black) cables as parallel and close together as possible to minimise electromagnetic interference fields. Features Model / SKU**SOLR650** Conductor cross-section**6.0 mm²** Delivery form**50 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (class 5) Temperature range-40°C to +120°C (on the conductor) Certification**IEC 62930 / EN 50618** Special featureHalogen-free, UV-resistant & short-circuit-proof  FAQs about solar cable red 50m 6mm²Why is 6mm² for 50 metres better than 4mm²?Due to the lower resistance. The electrical resistance adds up over a distance of 50 metres. With 6mm² you reduce the voltage drop by around a third compared to 4mm². This ensures a higher system voltage at the inverter and therefore a measurably higher yield.Can the cable be laid freely outdoors?Yes. The cable is specially certified for permanent outdoor installation. It is resistant to UV light, ozone and ammonia, which also qualifies it for use in agriculture.Is the cable flame-retardant?Yes. The XLPO insulation is flame-retardant and halogen-free. In the event of a fire, the cable produces hardly any smoke and no corrosive gases, which significantly increases safety in the building.

The solar cable SOLR675 (75 metres, 6mm²) in red is the high-performance solution for photovoltaic installations that have to efficiently cope with long distances and high currents. With a length of 75 metres and a reinforced cross-section of 6mm², this cable offers maximum reserves for string cabling on extensive roofs or the connection of module fields to inverters located far away. The red colouring serves to mark the positive pole (+) in accordance with standards.Certified according to international standard IEC 62930, the SOLR675 meets the most stringent quality requirements for permanent use under extreme conditions. The generous cross-section ensures that the voltage drop is minimised even over long cable runs, which directly results in a higher overall yield from your solar installation.Highlights at a glanceHigh efficiency: The cross-section of 6mm² massively minimises the electrical resistance, which is particularly decisive for efficiency over the distance of 75 metres.Certified safety: Complies with IEC 62930 (H1Z2Z2-K) standard for permanent use in photovoltaic direct current systems up to 1500V.Optimum project length: 75 metres in one piece enable continuous installation over long distances without unnecessary joints or additional plug connections.Extremely resistant: The high-quality XLPO double insulation protects the cable from embrittlement due to intense UV radiation, ozone and weathering for decades.Corrosion-protected conductor: Fine-stranded, tinned copper offers consistently excellent conductivity and effective protection against oxidation, even in humid or salty air.Wide temperature range: Safe operation under the most adverse climatic conditions from -40°C to +90°C.Areas of applicationSOLR675 is the ideal choice for demanding long-distance connections:Large roof systems & commercial buildingsPerfect for the connection of solar modules to the inverter when it is installed over several floors or in a distant technical room.Open space & garden systemsIdeal for connecting distant module fields to the feed-in point with minimal losses.High-performance stand-alone systemsIdeally suited for 24V or 48V systems with high charging currents, where every volt retention at the battery counts.Installation & safety notesProfessional assemblyUse only high-quality MC4 connectors that are approved for 6mm² cross-sections to complete the cable. Gas-tight crimping is essential for long-term safety.Protection when laid undergroundAlthough the cable is weather-resistant, it must always be run in a suitable protective conduit when laid underground to protect it from mechanical influences.Parallel cable routingRoute positive (red) and negative (black) cables as closely together as possible to minimise electromagnetic interference fields and induction loops. Features Model / SKU**SOLR675** Conductor cross-section**6.0 mm²** Delivery form**75 metre ring** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** Special featureAcid & alkali resistant, halogen-free  FAQs about the solar cable red 75m 6mm²Why is 6mm² almost always the better choice for 75 metres in length?To keep power losses in check. Over a total length of 150 metres (supply and return), the resistance adds up considerably. A 6mm² cable reduces the voltage drop by around a third compared to 4mm², which means a noticeable increase in yield over the lifetime of the system.Can the cable also be laid indoors?Yes. Thanks to its flame-resistant and halogen-free XLPO insulation, the SOLR675 can be safely laid in buildings to route the energy from the roof to the inverter room.Does the cable fit into standard MC4 plugs?Yes, in the 6mm²-compatible versions. When buying connectors, ensure that they are designed for the cross-section range of 4–6mm² so that sealing and strain relief work perfectly.

The Solar Cable SOLS425 (25 metres, 4mm²) in black is the ideal solution for flexible and professional cabling of your photovoltaic system. With a length of 25 metres, this cable by the metre is perfectly suited for medium-sized projects, such as connecting module strings to the inverter or installing balcony power plants. The black colour serves as standard-compliant marking of the negative pole (-), making installation clear and safe.Manufactured according to the strict international standard IEC 62930, this cable meets the highest quality standards for long-term use in modern PV systems up to 1500V DC. The high-quality XLPO double insulation and the tinned copper conductor guarantee efficient energy transmission and maximum service life, even under demanding environmental conditions.Highlights at a glanceCertified safety: Complies with standard IEC 62930 (H1Z2Z2-K) for permanent use in photovoltaic DC systems up to 1500V.Optimum project length: 25 metres in one piece allow customised cuts for individual connection paths without unnecessary interfaces.Clear polarity: The black outer sheath provides a clear visual marking of the negative cable and prevents mix-ups during installation.Weatherproof & Robust: The UV-resistant and ozone-resistant double insulation protects the cable for decades from embrittlement caused by weather influences.Corrosion-protected conductor: Tinned electrolytic copper ensures permanently low contact resistance and provides effective protection against oxidation.Wide temperature range: Safe operation even under extreme climatic conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLS425 is versatile for private and commercial PV projects:House & Roof systemsIdeal for string cabling and connection to the charge controller or inverter over medium distances.Balcony power stationsPerfect for connecting the solar modules to the micro-inverter when it is mounted in a staggered or protected position indoors.Motorhomes & MarineReliable cabling for self-sufficient systems requiring resistance to vibrations, moisture and UV radiation.Installation & Safety InstructionsProfessional crimpingAs it is cable by the metre, exclusively high-quality MC4 connectors should be used for the connection. Gas-tight crimping with a special crimping tool is essential for long-term safety.Parallel cable routingRoute the black negative cable as parallel and as close as possible to the red positive cable to minimise electromagnetic interference (induction loops).Mechanical protectionLay the cable at sharp edges in such a way that the insulation is not damaged. Use corrugated pipes or cable ducts when passing through walls. Features Model / SKU**SOLS425** Conductor cross-section**4.0 mm²** Delivery form**25-metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (fine-stranded) Temperature range-40°C to +90°C (ambient) Standardisation**IEC 62930 / EN 50618** Special featureHalogen-free & flame-retardant  FAQs about the solar cable black 25m 4mm²What is the advantage of IEC 62930 certification?Maximum longevity in PV systems. This standard ensures the cable is halogen-free, flame-retardant and specially tested for resistance to high DC voltages and intensive UV radiation. It is considerably more robust than standard conventional cables.Can I also lay the cable indoors?Yes. Thanks to the flame-retardant and halogen-free properties of the XLPO insulation, the SOLS425 can be laid safely in buildings to transfer energy to the inverter room.Does the cable fit into standard MC4 plugs?Yes. The cable with 4mm² cross-section fits into all standard MC4 connectors designed for the 4–6mm² range. Ensure a clean installation for a watertight connection.

The solar cable SOLS450 (50 metres, 4mm²) in black is the ideal metered cable for photovoltaic projects that require flexible and secure wiring over medium distances. With a length of 50 metres, this roll offers ample scope for string cabling on rooftops or for connecting module arrays to the inverter. The black colouring is used for standard-compliant identification of the negative pole (-), which makes installation straightforward and minimises connection errors.Certified to the international standard IEC 62930, this cable fulfils the highest requirements for safety and durability. It is specially designed for the harsh conditions outdoors and, thanks to its high-quality material composition, ensures efficient energy transmission over the entire service life of your solar installation.Highlights at a glanceCertified standard: Complies with standard IEC 62930 (H1Z2Z2-K), which guarantees maximum suitability for photovoltaic DC systems up to 1500V.Generous range: 50 metres in one piece allow uninterrupted installation without additional connectors between module array and technical room.Clear polarity: The black outer sheath provides clear visual separation of the negative cable, increasing safety during installation and maintenance.Weather- & UV-resistant: The quality XLPO double insulation provides lasting protection against embrittlement from sunlight, ozone, and extreme weather.Optimum conductivity: The finely stranded conductor made from tinned copper provides excellent corrosion protection and permanently low transition resistances.High thermal load capacity: Reliable operation in a wide temperature range from -40°C to +90°C.Areas of applicationThe SOLS450 is the ideal choice for a wide variety of installation scenarios:Single-family homes & rooftop systemsPerfect for connecting the solar modules to the inverter when it is installed in the basement or utility room.Balcony systems & garden installationsIdeal for installations where a greater distance between the panels and the feed-in point needs to be bridged.Mobile solar systemsUse in self-sufficient systems for tiny houses or larger mobile homes, where certified industrial quality is important.Installation & safety instructionsProfessional connectionFor assembly, use only high-quality MC4 connectors and ensure precise crimping with special solar crimping pliers.Mechanical fixationFasten the cable at regular intervals with UV-resistant cable ties to minimise mechanical stress from wind or self-weight.Avoiding induction loopsLay the black negative cable as parallel and as close as possible to the red positive cable to reduce electromagnetic interference and the risk of lightning induction. Features Model / SKU**SOLS450** Conductor cross-section**4.0 mm²** Delivery form**50 metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +90°C (ambient) Certificates**IEC 62930 / EN 50618 (H1Z2Z2-K)** Special featureHalogen-free & short-circuit proof  FAQs about the solar cable black 50m 4mm²Why is IEC 62930 certification important?It guarantees longevity in PV systems.This standard ensures that the cable is halogen-free, flame-retardant and specially tested against stresses from high DC voltages and UV light. This distinguishes it significantly from conventional installation cables.Is 4mm² sufficient for a 50m long cable?Yes, for moderate currents.In a typical module string with high voltage, the voltage drop at 50 metres and 4mm² is usually completely unproblematic. For systems with very low voltages (e.g. 12V), however, the voltage drop should be checked in advance.Is the cable resistant to acids and alkalis?Yes.The XLPO insulation provides good resistance to chemical influences, which is particularly advantageous for installations near industrial areas or in agriculture (ammonia exposure).

The SOLS475 solar cable (75 metres, 4mm²) in black is the ideal solution for cabling photovoltaic systems over long distances. With a length of 75 metres on the reel, it offers maximum flexibility for string cabling on extensive roofs or when connecting module arrays to the inverter in larger buildings. The black labelling is used for standard-compliant identification of the negative pole (-), which significantly increases safety and clarity during installation.Manufactured according to the strict international standard IEC 62930, this cable fulfils the highest quality requirements for long-term use in modern PV systems up to 1500V DC. The high-quality XLPO double insulation and the tinned copper conductor guarantee efficient energy transmission and maximum service life, even under demanding environmental conditions.Highlights at a glanceCertified safety: Complies with the IEC 62930 standard (H1Z2Z2-K) for permanent use in photovoltaic direct current systems up to 1500V.High range: 75 metres in one piece allow individual cuts for customised string connections without unnecessary separation points.Clear polarity: The black outer sheath ensures clear labelling of the negative cable and prevents errors during installation.Weatherproof & robust: The UV-resistant and ozone-resistant double insulation protects the cable for decades from embrittlement caused by intensive solar radiation.Corrosion-protected conductor: Tinned electrolytic copper guarantees permanently low contact resistance and effectively protects against oxidation.Wide temperature range: Safe operation under extreme climatic conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLS475 is the ideal choice for demanding installation scenarios:Larger roof systemsPerfect for connecting the solar modules to the inverter when it is installed over several floors or in a remote technical room.Commercial PV projectsIdeal for string cabling in larger systems, where high reliability and standard-compliant implementation are required.Off-grid & hybrid systemsUsed in self-sufficient power supplies for remote buildings or farms where long cable runs need to be bridged.Assembly & safety instructionsProfessional assemblyAs this cable is sold by the metre, we recommend using high-quality MC4 connectors and a professional crimping tool for solar cables.Avoidance of induction loopsRoute the black negative conductor as parallel and as close as possible to the red positive conductor to minimise electromagnetic interference fields and the risk of lightning induction.Mechanical protectionFor penetrations or sharp edges, use protective tubing or cable conduits to guarantee the integrity of the double insulation for the long term. Features Model / SKU**SOLS475** Conductor cross-section**4.0 mm²** Delivery form**75 metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (class 5) Temperature range-40°C to +90°C (ambient) Standardisation**IEC 62930 / EN 50618** Special featureAcid & alkali resistant, halogen-free  FAQs about the solar cable black 75m 4mm²Why is 4mm² often sufficient for 75 metres?Due to the high string voltage.In modern PV systems, modules are often connected in series, which increases the voltage and keeps the current (amperes) relatively low. At high voltages, the percentage power loss with 4mm² is usually very low, even over 75 metres.Can the cable be permanently laid outdoors?Yes.The cable is specially certified for outdoor installation. It is resistant to ammonia (important in agriculture), ozone and intense UV radiation.What is the advantage over conventional rubber cables?The chemical cross-linking of the insulation.The XLPO insulation (cross-linked polyolefin) does not melt in the heat and does not become brittle in winter. It is also flame retardant and halogen-free, which increases safety in buildings in the event of fire.

The solar cable SOLS625 (25 metres, 6mm²) in black is the ideal solution for photovoltaic installations that require high current carrying capacity and minimal energy losses. With a length of 25 metres and a reinforced cross-section of 6mm², this cable offers the perfect balance between flexibility and performance—whether for string cabling on the roof or connecting powerful balcony power systems. The black colour serves as the standard-compliant identification of the negative pole (-).Manufactured according to the international standard IEC 62930, this cable meets the strictest requirements for safety and durability in modern PV systems up to 1500V DC. The generous cross-section ensures that heat generation is minimised even in modules with high output currents and that the efficiency of your system is maximised.Highlights at a glanceCertified safety: Complies with IEC 62930 (H1Z2Z2-K) standard for continuous use in photovoltaic DC systems up to 1500V.High efficiency: The 6mm² cross-section significantly minimises electrical resistance and reduces voltage drops compared to standard cables.Optimal project length: 25 metres enable custom cuts for medium distances without unnecessary joints or plug connections.Weather & UV-resistant: The high-quality XLPO double insulation protects the cable for decades against embrittlement caused by sunlight, ozone and extreme weather conditions.Corrosion-protected conductor: Fine-stranded, tinned copper provides lasting top conductivity and effectively protects against oxidation in moist environments.Extreme temperature range: Reliable operation under the harshest conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLS625 is versatile for demanding PV projects:Modern roof systemsIdeal for connecting high-performance modules (500Wp+) to the inverter for loss-free transport of high currents.Balcony power systems & stand-alone systemsPerfectly suitable if the inverter or charge controller is installed somewhat further away and every watt of power is to be preserved.Motorhomes & marineRobust cabling for self-sufficient systems where vibration, moisture, and high loads are factors.Installation & safety instructionsProfessional preparationFor this cross-section, only use MC4 connectors that are explicitly approved for 6mm² cables. A gas-tight crimp is essential for long-term safety.Observe bending radiiDespite the high flexibility of the fine-stranded conductors, the cable should not be bent below the minimum permitted bending radius in order to preserve the insulation.Mechanical protectionUse protective conduits or edge protection profiles at feed-throughs or sharp edges to permanently ensure the integrity of the double insulation. Specifications Model / SKU**SOLS625** Conductor cross-section**6.0 mm²** Delivery form**25 metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (class 5) Temperature range-40°C to +120°C (on conductor) Standard**IEC 62930 / EN 50618** PropertiesHalogen-free, flame-retardant, UV-resistant  FAQs about solar cable black 25m 6mm²Is 6mm² necessary for 25 metres in length?It is advisable.Especially with modern modules delivering currents from 13A to 18A, 6mm² offers significantly more safety against heating and reduces voltage drops. It is a future-proof choice for maximum yields.Can the cable be installed indoors?Yes.Thanks to the flame-retardant and halogen-free properties of the XLPO insulation, the SOLS625 can be safely installed in buildings to transmit energy from the roof to the plant room.Does the cable fit in standard MC4 connectors?Only in suitable 6mm² versions.There are MC4 connectors for different cross-section ranges. Make sure to use connectors designed for 4–6mm² so that strain relief and sealing are ensured.

The Solar cable SOLS650 (50 metres, 6mm²) in black is the ideal cable by the metre for photovoltaic projects that demand the highest standards of efficiency and durability. With a length of 50 metres and a reinforced cross-section of 6mm², this cable provides perfect reserves for string cabling on house roofs or connecting distant module fields. The black colouring serves as a standard-compliant identification of the negative pole (-), which makes installation clear and minimises the risk of reversed polarity.Certified to the international standard IEC 62930, this cable meets the strictest requirements for use in modern PV systems up to 1500V DC. The generous cross-section ensures that even with high current from modern high-performance modules, the voltage drop is minimised and the total yield of your system is maximised.Highlights at a glanceMaximum efficiency: The 6mm² cross-section massively reduces electrical resistance and achieves minimal voltage drop, especially over distances of 50 metres.Certified safety: Complies with IEC 62930 standard (H1Z2Z2-K) for continuous use in photovoltaic DC systems up to 1500V.Optimum project length: 50 metres in one piece allow uninterrupted installation without additional connectors between the module field and inverter.Weather & UV resistant: The premium XLPO double insulation protects the cable for decades against embrittlement from sun, ozone and extreme weather conditions.Corrosion-protected conductor: Fine-stranded, tinned copper delivers best conductivity in the long run and effectively protects against oxidation, even in damp or salty environments.High thermal load capacity: Reliable operation in a wide temperature range from -40°C to +90°C.Areas of applicationThe SOLS650 is the ideal choice for demanding installation scenarios:Large roof systemsPerfect for connecting the solar modules to the inverter when this is installed in the basement or a distant technical room.High-performance balcony power plantsIdeal for systems with modern modules (500Wp+), to safely and losslessly transport the high currents.Island & battery storageExcellent for 24V or 48V systems where low voltage drops are crucial for optimal battery charging.Assembly & safety instructionsProfessional connectionFor assembly, use only high-quality MC4 connectors approved for 6mm² cross-sections. A precise crimp using a special solar crimping tool is essential.Mechanical fixingAttach the cable at regular intervals with UV-resistant cable ties to prevent mechanical stress due to wind or its own weight on the connections.Avoidance of induction loopsRoute the black negative cable as parallel and close as possible to the red positive cable to minimise electromagnetic interference fields and the risk of induction by lightning. Features Model / SKU**SOLS650** Conductor cross-section**6.0 mm²** Delivery form**50 metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (class 5) Temperature range-40°C to +120°C (on the conductor) Certification**IEC 62930 / EN 50618** Special featureHalogen-free, UV-resistant & short-circuit-proof  FAQs about the solar cable black 50m 6mm²Why is 6mm² for 50 metres better than 4mm²?Because of the lower resistance.Over a distance of 50 metres, the electrical resistance adds up. With 6mm² you reduce the voltage drop by about a third compared to 4mm². This ensures higher system voltage at the inverter and thus measurably higher yield.Can the cable be laid freely outdoors?Yes.The cable is specially certified for permanent outdoor installation. It is resistant to UV light, ozone and ammonia, which also qualifies it for use in agriculture.Is the cable flame-retardant?Yes.The XLPO insulation is flame-retardant and halogen-free. In the event of fire, the cable hardly develops any smoke and no corrosive gases, which significantly increases building safety.

The solar cable SOLS675 (75 metres, 6mm²) in black is the high-performance solution for photovoltaic installations that need to efficiently handle long distances and high currents. With a length of 75 metres and a reinforced cross-section of 6mm², this cable offers maximum reserves for string cabling on extensive roofs or connecting module arrays to distant inverters. The black colour provides standard-compliant identification of the negative terminal (-).Certified according to the international standard IEC 62930, the SOLS675 meets the strictest quality requirements for permanent use under extreme conditions. The generous cross-section ensures that voltage drop is minimised even on long cable runs, directly resulting in a higher overall yield of your solar system.Highlights at a glanceHigh efficiency: The 6mm² cross-section massively minimises electrical resistance, which is critical for efficiency at the 75-metre distance.Certified safety: Complies with IEC 62930 (H1Z2Z2-K) standard for permanent use in photovoltaic DC systems up to 1500V.Optimal project length: 75 metres in one piece allows uninterrupted laying over long distances without unnecessary couplings or additional plug connections.Extremely resistant: The high-quality XLPO double insulation protects the cable for decades against embrittlement due to intense UV radiation, ozone and weather.Corrosion-protected conductor: Fine-stranded, tinned copper delivers excellent conductivity for the long term and effectively protects against oxidation, even in humid or salty air.Wide temperature range: Safe operation under the harshest climatic conditions from -40°C to +90°C.Areas of applicationThe SOLS675 is the ideal choice for demanding long-distance connections:Larger roof systems & commercial propertyPerfect for connecting the solar modules to the inverter when the inverter is installed over several floors or in a remote technical room.Ground-mounted & garden systemsIdeal for connecting distant module arrays to the feed-in point with minimal loss.Powerful stand-alone systemsIdeally suited for 24V or 48V systems with high charging currents, where maintaining every volt at the battery matters.Assembly & Safety instructionsProfessional assemblyTo complete the cable, only use high quality MC4 connectors approved for 6mm² cross-section. A gas-tight crimp is essential for long term safety.Protection in underground layingAlthough the cable is weather-resistant, it must always be routed in a suitable protective conduit when laid in the ground to protect it from mechanical influences.Parallel cable routingLay the black negative cable as close as possible to the red positive cable to minimise electromagnetic interference and induction loops. Features Model / SKU**SOLS675** Conductor cross-section**6.0 mm²** Delivery form**75 metre ring** ColourBlack (negative terminal) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (at conductor) Standards**IEC 62930 / EN 50618** Special featuresAcid & alkali resistant, halogen-free  FAQs about the solar cable black 75m 6mm²Why is 6mm² for a length of 75 metres almost always the better choice?To keep power losses in check. Over a total length of 150 metres (out and back), the resistance increases significantly. A 6mm² cable reduces the voltage drop by about a third compared to 4mm², which means a noticeable increase in yield over the life of the system.Can the cable also be installed indoors?Yes. Thanks to its flame-retardant and halogen-free XLPO insulation, the SOLS675 can be safely installed in buildings to carry energy from the roof to the inverter room.Does the cable fit in standard MC4 connectors?Yes, in the 6mm² compatible variants. When purchasing connectors, ensure that they are suitable for the cross-section range of 4–6mm² so that sealing and strain relief operate perfectly.

The Deye SUN-M80G4-EU-Q0 800W micro-inverter is the ideal solution for your balcony power plant. With this powerful inverter, you can efficiently convert solar energy into usable household electricity and directly reduce your electricity costs.Your benefits at a glanceMaximum efficiencyTwo independent MPPT trackers ensure the best possible yield from your solar panels, even in partial shade.Smart monitoringThanks to the built-in Wi-Fi module, you can monitor your electricity production anytime, anywhere via the free smartphone app.Weatherproof and safeWith an IP67 rating, the housing is completely dust- and waterproof, making it ideal for long-term outdoor use.Easy installationCommissioning is quick and straightforward via secure plug connections based on the tried-and-tested plug-&-play principle.Reliable energy management for your homeThe Deye micro-inverter acts as the intelligent heart of your mini solar system. It reliably converts the DC power generated into grid-compliant AC power, which flows directly into your home’s electrical system. This automatically covers the continuous power requirements of your base-load appliances, such as fridges, Wi-Fi routers or devices on standby. Advanced control technology ensures that the absolute maximum output is extracted from every hour of sunshine. This means your investment pays for itself quickly and you gain greater independence from rising energy prices.Technical specificationsInput (DC – direct current)The recommended PV power output is 210 to 560 W per input. The inverter features 2 independent MPP trackers. The maximum input voltage is 60 V, the MPPT voltage range is 25 V to 55 V and the start voltage is 20 V. The maximum input current is 2 × 13.0 A, the maximum short-circuit current is 2 × 19.5 A.Output (AC – alternating current)The rated AC power is 800 W or 800 VA and can be throttled via the app. The rated voltage is 220 / 230 V single-phase, the rated frequency 50 / 60 Hz. The maximum output current is 3.7 A. The power factor is > 0.99 and is adjustable from 0.8 lead to 0.8 lag. The total harmonic distortion (THDi) is less than 3%.EfficiencyThe maximum efficiency is 96.5%, the Euro efficiency is 96.0%. The MPPT efficiency is over 99%. Night-time consumption is less than 50 mW.General data (Mechanical & Environmental)Dimensions: 280.5 × 190 × 40 mm. Weight: approx. 3.0 kg. IP67 protection rating ensures dust and water resistance. Operating temperature range: -40 °C to +65 °C. Cooling via natural convection, fanless.Safety & FeaturesCommunication takes place via integrated Wi-Fi (2.4 GHz) for app monitoring. NA protection is implemented via an integrated relay in accordance with VDE-AR-N 4105. Protection functions include DC reverse polarity protection, short-circuit protection, anti-islanding, as well as overcurrent and overvoltage protection. The manufacturer’s warranty is 15 years.Contents1x Deye SUN-M80G4-EU-Q0 micro inverter1x Wi-Fi antenna1x User and Installation Manual

The Deye BOS-B80.3 kWh PRO-A3 is a highly efficient, three-phase high-voltage battery storage system developed specifically for the demanding requirements of the commercial and industrial (C&I) sectors. It replaces rigid and difficult-to-scale storage systems with a modular, turnkey cabinet solution, whilst offering intelligent functions to optimise commercial energy flow.With its sophisticated design, the BOS-B system is not just a passive energy storage solution, but serves as a future-proof foundation for your company’s energy management (Industrial Storage Hub). It supports seamless integration with high-performance Deye hybrid inverters (such as the SUN-125K series) and ensures that your business retains maximum control over its energy costs at all times.Highlights at a glanceLarge-scale industrial capacity: Offers a full 80.3 kWh of usable energy in a single, compact cabinet system, based on long-lasting lithium iron phosphate (LiFePO4) technology.High-voltage efficiency: Connecting the modules in series ensures a high system voltage, which minimises conversion losses and enables extremely rapid energy delivery.Excellent cycle stability: With over 6,000 charge cycles, the system guarantees an extremely long service life and maximum investment security, even with daily, intensive use.Intelligent Master BMS: The integrated control system in the cabinet continuously monitors cell voltages, temperatures and currents, and ensures fully automatic cell balancing.Safety functions: Multi-stage protection mechanisms, including automatic shutdown in the event of overcurrent, overvoltage or thermal irregularities, guarantee worry-free operation around the clock.Flexible scalability: Multiple cabinet units can be easily connected in parallel to flexibly scale the total capacity alongside your business growth.Areas of applicationThe Deye BOS-B80.3 kWh PRO-A3 is the perfect addition to commercial PV systems and industrial infrastructure:Peak shaving: Reduction in grid usage charges through the targeted absorption of expensive electricity peaks in the industrial production process.Optimisation of self-consumption: Efficient temporary storage of solar power from large industrial rooftops that is unused during the day, to provide self-sufficient power for operations in the evening and at night.Emergency power & backup systems: Reliable protection of critical loads (such as IT infrastructure, cooling systems or sensitive production lines) in the event of power failures.Installation & Safety InstructionsInverter compatibility: The system is designed as a high-voltage storage solution and must be operated with compatible Deye three-phase high-voltage hybrid inverters.Installation & environment: Due to the high weight of the system, the cabinet solution should be installed on a load-bearing, level surface and in a well-ventilated, temperature-controlled indoor environment.Installation by qualified personnel: Due to the high-voltage direct current (DC) environment and the industrial power ratings, installation, cabling and commissioning must be carried out exclusively by certified qualified electricians. Features ModelBOS-B80 Pro-A3 Battery typeLiFePO4 Module energy (kWh)16,08 Module nominal voltage (V)51,2 Module capacity (Ah)314 Number of battery modules in series5 System nominal voltage (V)256 System operating voltage (V)208~292 System capacity (kWh)80,3 Usable system capacity (kWh)72,27 Max. DC power (kW)46,08 Max. charge/discharge current (A)180 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Thermal managementSmart fan cooling CommunicationTCP / RS485 / CAN Protection classIP20 Dimensions (W × H × D, mm)1067 × 1305 × 800 Approx. system weight (kg)758 Installation typeRack-Mounted Recommended depth of discharge90% Cycle lifeEOL70% ≥ 6000 Warranty10 years CertificationsCE / IEC62619 / IEC62040 / UN38.3  FAQs on the Deye BOS-B80.3 kWh PRO-A3Can the 80.3 kWh capacity be expanded at a later date?Yes. The system has a modular design. To increase the total capacity, several of these cabinet units can be connected in parallel, enabling storage capacities in the megawatt range to be achieved.Is the master control unit (BMS) already integrated into the cabinet?Yes. The system is supplied as a plug-and-play cabinet solution, in which both the individual battery modules and the central cluster control unit (high-voltage BMS) are integrated into the rack, ready for operation.What advantages does LiFePO4 technology offer in industrial applications?Maximum safety and durability. Unlike conventional lithium-ion batteries, lithium iron phosphate cells are extremely thermally stable, non-flammable and offer a significantly higher number of charge cycles, even under heavy use.Does the system support control via an external energy management system (EMS)?Yes. Via the integrated communication interfaces, the storage system can be seamlessly connected to higher-level commercial energy management systems (EMS) to implement complex charging and discharging strategies.

The Deye BOS-B112.5 kWh PRO-A3 is a highly efficient, three-phase high-voltage battery storage system developed specifically for the demanding requirements of the commercial and industrial (C&I) sectors. It replaces rigid and difficult-to-scale storage systems with a modular, turnkey cabinet solution, whilst offering intelligent functions to optimise commercial energy flow.With its sophisticated design, the BOS-B system is not just a passive energy storage solution, but serves as a future-proof foundation for your company’s energy management (Industrial Storage Hub). It supports seamless integration with high-performance Deye hybrid inverters (such as the SUN-125K series) and ensures that your business retains maximum control over its energy costs at all times.Highlights at a glanceLarge-scale industrial capacity: Offers a full 112.5 kWh of usable energy in a single, compact cabinet system, based on long-lasting lithium iron phosphate (LiFePO4) technology.High-voltage efficiency: Connecting the modules in series ensures a high system voltage, which minimises conversion losses and enables extremely rapid energy delivery.Excellent cycle stability: With over 6,000 charge cycles, the system guarantees an extremely long service life and maximum investment security, even with daily, intensive use.Intelligent Master BMS: The integrated control system in the cabinet continuously monitors cell voltages, temperatures and currents, and ensures fully automatic cell balancing.Safety functions: Multi-stage protection mechanisms, including automatic shutdown in the event of overcurrent, overvoltage or thermal irregularities, guarantee worry-free operation around the clock.Flexible scalability: Multiple cabinet units can be easily connected in parallel to flexibly scale the total capacity alongside your business growth.Areas of applicationThe Deye BOS-B112.5 kWh PRO-A3 is the perfect complement to commercial PV systems and industrial infrastructure:Peak shaving: Reduction in grid usage charges through the targeted absorption of expensive electricity peaks in the industrial production process.Optimisation of self-consumption: Efficient temporary storage of solar power from large industrial rooftops that is unused during the day, to provide self-sufficient power for operations in the evening and at night.Emergency power & backup systems: Reliable protection of critical loads (such as IT infrastructure, cooling systems or sensitive production lines) in the event of power failures.Installation & safety instructionsInverter compatibility: The system is designed as a high-voltage storage solution and must be operated with compatible Deye three-phase high-voltage hybrid inverters.Installation & environment: Due to the high weight of the system, the cabinet solution should be installed on a load-bearing, level surface and in a well-ventilated, temperature-controlled indoor environment.Installation by qualified personnel: Due to work in the high-voltage direct current (DC) range and the industrial power classes, installation, cabling and commissioning must only be carried out by certified qualified electricians Features ModelBOS-B112 Pro-A3 Battery typeLiFePO4 Module energy (kWh)16,08 Module nominal voltage (V)51,2 Module capacity (Ah)314 Number of battery modules in series7 System nominal voltage (V)358,4 System operating voltage (V)291,2~408,8 System capacity (kWh)112,5 Usable system capacity (kWh)101,25 Max. DC power (kW)64,512 Max. charge/discharge current (A)180 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Thermal managementSmart fan cooling CommunicationTCP / RS485 / CAN Protection classIP20 Dimensions (W × H × D, mm)1067 × 1305 × 800 Approx. system weight (kg)1010 Installation typeRack Mounted Recommended depth of discharge90% Cycle lifeEOL70% ≥ 6000 Warranty10 years CertificationsCE / IEC62619 / IEC62040 / UN38.3  FAQs on the Deye BOS-B112.5 kWh PRO-A3Can the 112.5 kWh capacity be expanded at a later date?Yes. The system has a modular design. To increase the total capacity, several of these cabinet units can be connected in parallel, enabling storage capacities in the megawatt range to be achieved.Is the master control unit (BMS) already integrated into the cabinet?Yes. The system is supplied as a turnkey cabinet solution, in which both the individual battery modules and the central cluster control unit (high-voltage BMS) are integrated into the rack, ready for operation.What advantages does LiFePO4 technology offer in industrial applications?Maximum safety and durability. Unlike conventional lithium-ion batteries, lithium iron phosphate cells are extremely thermally stable, non-flammable and offer a significantly higher number of charge cycles, even under heavy use.Does the system support control via an external energy management system (EMS)?Yes. Via the integrated communication interfaces, the storage system can be seamlessly connected to higher-level commercial energy management systems (EMS) to implement complex charging and discharging strategies.

The Deye BOS-G 75 PRO high-voltage storage set is a reliable and high-performance storage solution for commercial applications and demanding private households. With a total capacity of 76.80 kWh, modular expandability and intelligent battery management, it meets high requirements for safety, efficiency and flexibility.Key features at a glanceHigh capacity: 76.80 kWh gross storage capacity for large energy systemsUsable energy: 69.12 kWh at 90 percent depth of dischargeFlexible scalability: Up to 16 battery racks can be operated in parallelIntelligent control: Integrated BMS protects against overcharging, deep discharge, overcurrent and overheatingEasy integration: Quick installation in the 19-inch rack formatEfficient energy storage for modern projectsThe BOS-G 75 PRO, with its high voltage of 768.0 Volts and a wide operating voltage range from 660 to 876.0 Volts, provides an excellent basis for integration into existing energy systems. The lithium iron phosphate technology used ensures high safety, low self-discharge and a long service life.Modular and customisableThe system architecture allows flexible expansion to up to 16 parallel battery racks and AC-parallel operation of up to 10 Deye inverters. This means the system can be precisely adapted to increasing requirements and remains scalable in the long term.Safe energy managementThe integrated BMS permanently monitors cell voltages, temperatures and states of charge. It actively protects against critical operating conditions and optimises battery unit service life through automatic cell balancing.Who is the Deye BOS-G 75 PRO suitable for?The high-voltage storage set is ideal for:Commercial enterprises with high energy consumption or emergency power requirementsLarge photovoltaic systems with a focus on optimising on-site consumptionPrivate households with above-average energy consumptionProject developers who need a modular, certified high-voltage system  ModelBOS-G75 PRO Battery typeLiFePO4 Module capacity (kWh)5.12 Module nominal voltage (V)51.2 Module capacity (Ah)100 Number of battery modules15 Max. number of battery modules in series15 System nominal voltage (V)768.0 System operating voltage (V)660 ~ 876.0 System capacity (kWh)76.80 System usable capacity (kWh)69.12 Charge/discharge current (A) - recommendation50 Charge/discharge current (A) - nominal value100 Charge/discharge current (A) - peak discharge (2 min,25°C)125 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Communication portCAN2.0, RS485 Humidity5% ~ 85%RH Altitude≤3000m IP protection rating of the housingIP20 Storage temperature (°C)0 ~ 35 Installation locationRack installation / floor mounting Recommended depth of discharge90% Cycle life≥ 6000 Warranty10 years CertificationsUN38.3 / CE / CE-EMC / IEC62040 / CEC / VDE  FAQs about the Deye BOS-G 75 PRO high-voltage storage setWhat storage capacity does the BOS-G 75 PRO provide and how much of it is usable?The set consists of 15 LiFePO₄ modules, each with a gross capacity of 5.12 kWh. This results in a total storage capacity of 76.80 kWh. At 90% depth of discharge, around 69.12 kWh of usable energy is available.What protection and management functions does the BMS provide?The integrated battery management system continuously monitors and protects against overvoltage and undervoltage, overcurrent, short circuits and temperature deviations. It also provides cell balancing and stable charging and discharging conditions.Which electrical parameters are relevant?Operating voltage: 660 to 876.0 VNominal voltage: 768.0 V DCContinuous current: 100 A, peak discharge: 125 AIs the system modularly expandable?Yes, the modular concept allows parallel operation of up to 16 battery racks and integration of up to 10 inverters in the AC network.In which temperature range can the storage system be operated?Discharging: from -20 °C to +55 °CCharging: from 0 °C to +55 °C Scope of supply Deye BOS-G75 PRO high-voltage storage set (76.80 kWh) with rack systemSystem compositionThis product is a set and consists of a rack system, a Deye BOS-G-PDU-2 high-voltage control box and 15 individual BOS-G-Pack5.1 battery modules.Component 1: Deye Rack system / Battery cabinetA rack to accommodate the control box and the battery modules.Component 2: Deye BOS-G-PDU-2 high-voltage control boxThe central control unit for communication, protection and system management.Component 3 to 17: Fifteen Deye BOS-G-Pack5.1 high-voltage battery modulesFifteen high-voltage battery modules, each with 5.12 kWh.Accessories and cablingBattery connection cables (plus & minus)Communication cables (CAN/RS485)Connecting bridges / series wiring cablesEarthing cableMounting accessories and installation instructions

The Deye BOS-G 80 PRO high-voltage storage set is a reliable and high-performance storage solution for commercial applications and demanding private households. With a total capacity of 81.92 kWh, modular expandability and intelligent battery management, it meets high standards of safety, efficiency and flexibility.Key features at a glanceHigh capacity: 81.92 kWh gross storage capacity for large energy systemsUsable energy: 73.73 kWh at 90 percent depth of dischargeFlexible scalability: Up to 16 battery racks can be operated in parallelIntelligent control: Integrated BMS protects against overcharging, deep discharge, overcurrent and overheatingEasy integration: Fast installation in 19-inch rack formatEfficient energy storage for modern projectsWith its high voltage of 819.2 volts and a wide operating voltage range of 704 to 934.4 volts, the BOS-G 80 PRO offers an excellent basis for integration into existing energy systems. The lithium iron phosphate technology used ensures high safety, low self-discharge and a long service life.Modular and customisableThe system architecture allows flexible expansion to up to 16 parallel battery racks and the AC parallel operation of up to 10 Deye inverters. This allows the system to be precisely adapted to increasing requirements and remains scalable in the long term.Safe energy managementThe integrated BMS continuously monitors the cell voltages, temperatures and states of charge. It actively protects against critical operating conditions and optimises the service life of the battery units through automatic cell balancing.Who is the Deye BOS-G 80 PRO suitable for?The high-voltage storage set is ideal for:Businesses with high energy consumption or emergency power requirementsLarge photovoltaic systems focusing on optimising self-consumptionPrivate households with above-average energy demandProject developers needing a modular, certified high-voltage system  ModelBOS-G80 PRO Battery typeLiFePO4 Module capacity (kWh)5.12 Module nominal voltage (V)51.2 Module capacity (Ah)100 Number of battery modules16 Max. number of battery modules in series16 System nominal voltage (V)819.2 System operating voltage (V)704 ~ 934.4 System capacity (kWh)81.92 System usable capacity (kWh)73.73 Charge/discharge current (A) - recommendation50 Charge/discharge current (A) - nominal value100 Charge/discharge current (A) - peak discharge (2 min,25°C)125 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Communication interfaceCAN2.0, RS485 Humidity5% ~ 85%RH Altitude≤3000m IP protection class of housingIP20 Storage temperature (°C)0 ~ 35 Installation locationRack installation / Floor mounting Recommended depth of discharge90% Cycle life≥ 6000 Warranty10 years CertificationsUN38.3 / CE / CE-EMC / IEC62040 / CEC / VDE  FAQs on the Deye BOS-G 80 PRO high-voltage storage setWhat storage capacity does the BOS-G 80 PRO provide and how much of it is usable?The set consists of 16 LiFePO₄ modules each with 5.12 kWh gross capacity. This results in a total storage capacity of 81.92 kWh. With 90% depth of discharge, around 73.73 kWh usable energy is available.What protection and management functions are provided by the BMS?The integrated battery management system continuously monitors and protects against over- and under-voltage, overcurrent, short circuit and temperature fluctuations. In addition, it ensures cell balancing and stable charging and discharging conditions.Which electrical parameters are relevant?Operating voltage: 704 to 934.4 VRated voltage: 819.2 V DCContinuous current: 100 A, peak discharge: 125 AIs the system modular and expandable?Yes, the modular concept allows the parallel operation of up to 16 battery racks and the integration of up to 10 inverters in the AC network.What is the temperature range for operation?Discharge: from -20 °C to +55 °CCharge: from 0 °C to +55 °C Scope of delivery Deye BOS-G80 PRO high-voltage storage set (81.92 kWh) with rack systemSystem compositionThis product is a set and consists of a rack system, a Deye BOS-G-PDU-2 high-voltage control box and 16 individual BOS-G-Pack5.1 battery modules.Component 1: Deye rack system / battery cabinetA rack for accommodating the control box and the battery modules.Component 2: Deye BOS-G-PDU-2 high-voltage control boxThe central control unit for communication, protection and system management.Component 3 to 18: Sixteen Deye BOS-G-Pack5.1 high-voltage battery modulesSixteen high-voltage battery modules, each with 5.12 kWh.Accessories and cablingBattery connection cables (plus & minus)Communication cables (CAN/RS485)Connecting bridges / Series connection cablesEarthing cableMounting accessories and installation instructions

The Deye BOS-G 85 PRO high-voltage storage set is a powerful and reliable storage solution for commercial applications, demanding private households as well as larger energy projects. With a total capacity of 87.04 kWh, modular expandability and intelligent battery management, it meets high standards for safety, efficiency and flexibility. Highlights at a glance High capacity: 87.04 kWh gross storage capacity for large energy systems and maximum self-consumption optimisation Usable energy: approx. 78.33 kWh at 90 percent depth of discharge Modular design: 17 battery modules of 5.12 kWh each in a high-voltage cluster Flexible scalability: Up to 16 battery racks can be operated in parallel Intelligent control: Integrated BMS protects against overcharging, deep discharge, overcurrent and overheating Simple integration: Modular 19-inch rack system with CAN and RS485 communication Efficient energy storage for demanding projects With its high system voltage of 870.4 volts and a wide operating voltage range of 748 to 992.8 volts, the BOS-G 85 PRO provides a strong foundation for integration into modern energy systems. The lithium iron phosphate technology used ensures high safety, low self-discharge and a long service life. Modular and expandable The system architecture of the Deye BOS-G 85 PRO is designed for maximum flexibility. The storage set consists of 17 modules and can be flexibly expanded within the BOS-G Pro platform as required. Thanks to the ability to operate up to 16 racks in parallel and use several Deye inverters in an AC network, the system is suitable for growing load profiles and scalable commercial applications. Safe energy management The integrated battery management system permanently monitors cell voltages, temperatures and charge states. It actively protects against critical operating conditions and supports permanently reliable and efficient operation through automatic cell balancing. Who is the Deye BOS-G 85 PRO suitable for? The high-voltage storage set is ideal for: Commercial operations with high energy consumption or backup requirements Large photovoltaic systems focused on optimising self-consumption and managing peak loads Agricultural and industrial applications with high power requirements Project developers who require a modular and high-performance high-voltage system   ModelBOS-G85 PRO Battery typeLiFePO4 Module energy (kWh)5.12 Module nominal voltage (V)51.2 Module capacity (Ah)100 Number of battery modules17 System nominal voltage (V)870.4 System operating voltage (V)748 ~ 992.8 System capacity (kWh)87.04 System usable capacity (kWh)78.33 Charge/discharge current (A) – Recommendation50 Charge/discharge current (A) – nominal value100 Charge/discharge current (A) – peak discharge (2 min, 25°C)125 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Communication portCAN2.0 / RS485 Humidity5% ~ 85% RH Altitude≤3000 m IP protection class of the housingIP20 Storage temperature (°C)0 ~ 35 Recommended depth of discharge90% Cycle lifetime≥ 6000 (25 ± 2°C, 0.5C/0.5C, EOL70%) Warranty10 years CertificationsUN38.3 / CE / CE-EMC / IEC62040 / CEC / VDE  FAQs on the Deye BOS-G 85 PRO high-voltage storage set What storage capacity does the BOS-G 85 PRO deliver and how much of it is usable? The set consists of 17 LiFePO₄ modules, each with 5.12 kWh gross capacity. This results in a total storage capacity of 87.04 kWh. With a recommended depth of discharge of 90 percent, around 78.33 kWh of usable energy is available. What protection and management functions does the BMS handle? The integrated battery management system continuously monitors and protects against overvoltage and undervoltage, overcurrent, temperature deviations and critical operating states. It also ensures even and efficient operation of all modules through cell balancing. Which electrical parameters are relevant for the BOS-G 85 PRO? System nominal voltage: 870.4 V DC Operating voltage: 748 to 992.8 V Charge/discharge current: recommended 50 A, nominal value 100 A, peak discharge 125 A Is the system modularly expandable? Yes, the BOS-G 85 PRO is part of the modular BOS-G Pro platform. Several racks can be operated in parallel, allowing capacity and performance to be flexibly adapted to project-specific requirements. Within which temperature range can the storage unit be operated? Charging: 0 °C to +55 °C Discharging: -20 °C to +55 °C This makes the system suitable for a wide range of demanding indoor application environments.  Scope of delivery Deye BOS-G 85 PRO high-voltage storage set (87.04 kWh) System configuration This product is a set consisting of the BOS-G Pro rack system, the BOS-G-PDU-2 high-voltage control box and 17 individual BOS-G-Pack5.1 battery modules. Component 1: Deye rack system / battery cabinet Modular rack system for accommodating the high-voltage control box and the battery modules for a structured and service-friendly installation. Component 2: Deye high-voltage control box / BOS-G-PDU-2 The central control unit of the system manages communication, protection functions and system coordination. Component 3 to 19: Seventeen Deye BOS-G-Pack5.1 high-voltage battery modules High-voltage battery modules of 5.12 kWh each, which are modularly integrated into the rack system. 1 x set of battery connection cables (plus & minus) High-voltage power cable for connecting the control box to a compatible high-voltage hybrid inverter. 1 x communication cable (CAN/RS485) Data cable for communication between the storage system and the inverter. 1 x set of connecting bridges / series connection cables Connecting components for the serial connection of the modules within the system. 1 x mounting accessories Includes the necessary materials for mounting the components in the rack system. 1 x operating and installation manual Documentation for installation, commissioning and operation of the system.

OLIGHT ArkPro Ultra Class 1 - Onyx Black

The Deye SUN-10K-SG02LP1-EU-AM3-P is an extremely powerful, single-phase hybrid inverter of the latest generation, specially developed for demanding low-voltage photovoltaic systems. With a rated output power of 10 kW it is one of the most powerful single-phase devices on the market and enables significant optimisation of self-consumption as well as a seamless emergency power supply for large single-phase domestic networks or specific load groups.The abbreviation "P" stands for the support of High-current PV modules, which allows the connection of modern panels with high current ratings (up to 26 A per MPPT). It operates with 48 V low-voltage batteries combined and, thanks to its enormous charging and discharging capacity of up to 220 A, offers outstanding performance in the management of large battery storage systems.Highlights at a glanceEnormous 10 kW single-phase power: Ideal for large households or commercial applications with a single-phase system that require high load coverage.High-current inputs (26 A): Perfectly matched to the latest generation of PV modules with large cell formats and high short-circuit currents.48 V low-voltage system: Fully compatible with cost-effective and modularly expandable 48 V battery storage systems (e.g. LiFePO4 from Deye or Pylontech).220 A charging/discharging current: Enables extremely fast charging of the battery in strong sunlight and the powering of large loads from the battery.Full UPS functionality: Switches to stand-alone mode in less than 4 ms in the event of a power failure, ensuring that even sensitive electronics continue to operate without interruption.Three MPPT trackers: Offers maximum flexibility in roof coverage and optimises yield for different orientations or partial shading.AC-Coupling & Smart Load: Existing inverters can be easily integrated; furthermore, surplus energy can be specifically utilised for heat pumps or heating elements.Areas of applicationLarge single-phase domestic networksMaximum independence through the storage of large amounts of energy in cost-effective 48 V batteries.Off-grid & stand-alone solutionsThanks to its high output power of 10 kW, the unit is ideal for off-grid systems in remote areas.Retrofitting & expansionThanks to AC coupling, it can be installed in parallel with existing string inverters to retrofit a storage system.Installation & safety instructionsHigh battery currentsWith a discharge current of up to 220 A, it is essential to use heavy-duty cable cross-sections (e.g. 2x 50 mm² or 70 mm²) and appropriate high-current fuses.Thermal managementDespite the high efficiency, waste heat is generated at 10 kW output. Ensure the installation site has good air circulation and observe the minimum clearances.Phase coupling in the homeWhen installing in a German 3-phase mains supply, please observe the unbalanced load regulation (max. 4.6 kVA phase difference from the mains), unless a phase-balancing measurement or a zero-feed-in setup is used. Features ModelDeye SUN-10K-SG02LP1-EU-AM3-P Rated output power10 kW (10,000 watts) Phases1-phase*(230V) Battery typeLow voltage (LV) 48V Li-Ion / Lead Number of MPP trackers3 MPPT Max. PV input power13,000 watts*(13 kW) Max. charging/discharging current220 A Protection classIP65 (weatherproof) Special featureSupports Smart Load & AC-Coupling  FAQs for the Deye SUN-10K-SG02LP1-EU-AM3-PCan I supply a 3-phase house with this single-phase unit?Yes, via netting. The inverter feeds into one phase. A smart meter installed at the grid connection point ensures that the consumption of the other two phases is mathematically balanced (netting), so that the electricity meter effectively remains stationary.How many batteries can I connect?Virtually unlimited. Thanks to the 48 V system, many battery modules can be connected in parallel. The inverter communicates via CAN or RS485 with the leading battery management system (BMS). Please compare the battery with the compatibility list; this is recommended.Is the device suitable for outdoor use?Yes, thanks to IP65. The housing is dustproof and protected against water jets. Nevertheless, a shaded installation location is recommended in order to extend the service life of the electronics through lower thermal stress.

The Felicity FLB 48314TG1 is a powerful and safe low-voltage battery storage unit with modern LiFePO4 technology. It offers high cycle life, flexible expansion options and reliable energy supply for residential and commercial photovoltaic systems. With an integrated intelligent battery management system, remote monitoring functions and comprehensive protection mechanisms, it is the ideal solution for demanding energy storage projects.Highlights at a glance16 kWh LiFePO4 battery for maximum safety and durabilityRemote monitoring via integrated WiFi and BluetoothHigh charging and discharging rates for fast energy supplyExpandable up to 32 batteries (max. 512 kWh)Integrated intelligent BMS with comprehensive protectionCompatible with leading inverter brandsIntelligent energy management for maximum performanceThe FLB 48314TG1 ensures precise monitoring of all operating parameters, such as voltage, temperature and charge/discharge current, through its integrated BMS. Risks such as overcharging, deep discharge or overheating are reliably prevented. With a high charge and discharge current of up to 160 A continuous and 200 A peak (15 seconds), it is ideally suited for applications with high energy demand.Flexibility and easy expansionThanks to scalability up to 32 battery modules, the storage can be flexibly adapted to growing energy requirements. Communication via RS485 or CAN ensures smooth integration with inverters from well-known manufacturers. Thanks to floor mounting and compact design, the storage can be easily installed even where space is limited.Safety at the highest levelIn addition to its integrated battery management system, the FLB 48314TG1 is equipped with an aerosol fire extinguishing system, fuses and circuit breakers. The IP65 enclosure rating makes it resistant to dust and water, so it can also be used in demanding environments. The patented external fuse design allows for quick replacement in the event of service.Who is the Felicity FLB 48314TG1 suitable for?Operators of PV systems with high storage requirementsBusinesses and industry with continuous energy usageProjects with high safety requirementsInstallations in regions with demanding weather conditionsProperties  ModelFLB48314TG1 Battery typeLiFePO₄ System capacity (kWh)16 Nominal system voltage (V)51.2 System capacity (Ah)314 System operating voltage (V)44.8-57.6 Recommended depth of discharge (DoD)≥ 95 % Charge/discharge current (A) - recommendation60 Charge/discharge current (A) - peak discharge (2 min, 25°C)100 Operating temperature (°C)Charging: 0 ~ 55 / Discharging: -20 ~ 55 Communication interfaceCAN, RS485 Humidity5% ~ 95% IP enclosure ratingIP65 Storage temperature (°C)0 ~ 35 Dimensions (W/D/H, mm)600 * 450 * 180 Weight (kg)121 Installation locationFloor mounting Cycle life≥ 8,000 cycles ScalabilityUp to 32 units in parallel (512 kWh) Warranty10 years CertificationsOn request from sales  FAQs about the Felicity low-voltage battery storageHow much energy is available and how much is usable?The nominal energy is 16 kWh. With up to 95 % recommended depth of discharge, up to approx. 15.2 kWh can be used.How many charge cycles can be expected?The manufacturer states up to 8,000 cycles under laboratory conditions. Please note that real values depend on use, temperature and C-rate. Does the storage support remote monitoring and what interfaces are there?Yes, the storage supports remote monitoring via integrated WiFi and Bluetooth for remote reading of battery data. In addition, RS485 and CAN interfaces are available for communication with compatible inverters.Can I integrate the battery storage into my existing PV system?Yes, the FLB 48314TG1 is compatible with leading inverter brands and can easily be integrated into existing photovoltaic systems.Is remote monitoring possible?Yes, thanks to integrated WiFi and Bluetooth you can conveniently monitor all operating data of the storage system remotely.How many battery modules can be connected in parallel?The storage is expandable to up to 32 units and thus reaches a total capacity of up to 512 kWh. Scope of delivery Felicity FLB 48314TG1 battery storage: 1 x Felicity 16 kWh battery storage (FLB 48314TG1)The central storage unit with a 314 Ah capacity. It contains the intelligent battery management system (BMS) and usually also an integrated aerosol fire extinguishing system.1 x set of battery connection cables (plus & minus)A pair of pre-assembled high-power cables (red and black) for connecting the storage unit to an external inverter.1 x communication cable (CAN/RS485)A data cable (typically with RJ45 connectors) to ensure communication between the battery BMS and the inverter.1 x earthing cableA protective earth cable (yellow-green) for proper earthing of the metal casing.1 x mounting accessories (floor mounting)This model is designed as a mobile, free-standing unit and is often supplied with pre-installed castors. Due to its very high weight of approx. 155 kg, wall mounting is excluded.1 x operating and installation instructionsA printed manual with all safety-relevant instructions, installation steps and configuration guidelines.1 x set of mounting materialsIncludes materials for attachment of an anti-tip safety device.

The Deye GB-W94 is the flagship of Deye's cabinet-based high-voltage storage systems. With a massive total capacity of 94 kWh it marks the summit of the modular HV series and has been specially designed for industrial applications as well as large-scale energy projects. It provides a complete all-in-one solution for users with the highest demands in terms of capacity, resilience and efficiency.Thanks to the intelligent interconnection of high-performance battery modules in a sturdy cabinet system, the GB-W94 supplies the required energy for complex load profiles. In combination with Deye hybrid inverters, it forms a highly efficient power plant that maximises self-consumption and reduces dependency on public power grids to a minimum.Highlights at a glanceMaximum energy density: With 94 kWh capacity, the system provides one of the largest storage capacities in its class for business and industry.Future-proof LiFePO4 cells: Uses lithium iron phosphate technology for maximum thermal stability and a superior service life of over 6000 cycles.Highly efficient HV design: The high operating voltage ensures minimal loss during energy transmission and allows the supply of high-performance consumers.Integrated master BMS: A state-of-the-art management system continuously monitors all parameters and ensures optimal power distribution and cell maintenance.Industrial cabinet system: The robust construction protects the modules from external influences and enables space-saving installation in the technical room.Outstanding load capability: Designed to buffer massive load peaks and, in the event of an emergency power supply, to supply even heavy machinery or entire building sections.Cloud-based monitoring: Seamless integration into the Deye platform for monitoring performance and predictive maintenance analysis.Areas of applicationThe GB-W94 system redefines the boundaries of energy independence:Industry & ProductionCompensation of peak loads (peak shaving) and provision of process energy to reduce grid charges.Large agricultural complexesSelf-sufficient supply of automated barns, large PV-powered irrigation systems or processing plants.Neighbourhood solutions & microgridsCentral storage unit for residential settlements or remote hotel complexes in off-grid operation.Data centres & logistics centresSecuring critical infrastructures through enormous capacity reserves for uninterruptible power supply (UPS).Installation & safety instructionsStatic requirementsThe total weight of this system is considerable. The installation location must have a tested, load-bearing foundation (concrete).Fire protection & safetyInstallation should take place in a separate technical room that complies with the applicable standards for large battery storage and provides sufficient ventilation.Certified installationDue to the complexity and high voltages, commissioning may only be carried out by qualified personnel trained by Deye. Properties  ModelDEYGB-W94 Battery typeLiFePO4 Number of battery modules in series8 Nominal system voltage409.6 Vdc System operating voltage332.8 ~ 467.2 Vdc System energy94 kWh Usable energy84.6 kWh Nominal charging/discharging capacity94.2 kW Continuous charging/discharging current230 A Peak current322 A (1 s) CommunicationCAN / RS485 Thermal ManagementNatural air cooling Recommended depth of discharge90 % Protection classIP20 Air humidity0 ~ 85 % Altitude≤ 3000 m Noise level≤ 50 dB Type of installationFloor Mount Warranty10 years FAQs about the Deye GB-W94 battery systemCan this system support a whole business in the event of a power outage?Yes, depending on the total load.With 94 kWh of capacity and the corresponding hybrid inverters, the system can carry significant loads for long periods of time and ensures a seamless transition to island operation.How is the longevity of the storage guaranteed?Thanks to the active BMS.The system continuously equalises charge differences between the modules and protects the cells from deep discharge, overcharging and extreme temperatures.Is the system compatible with wind turbines?Yes, without a hitch.Via a compatible Deye inverter, energy from various sources (PV, wind, diesel generator) can be centrally fed and stored in the GB-W94 system.How is delivery of such a system handled?Due to the size, by forwarding agent.The system is delivered securely packaged. On site, special lifting equipment is often required to position the cabinet in its final location. Scope of delivery1 x Deye GB-W-PDU-28 x Deye GB-W-Pack12-2-A3 battery module1 x Deye GB-W-Base1 x Top Cover

The Deye SUN-20K-SG05LP3-EU-SM2 offers a reliable and efficient solution for energy conversion in photovoltaic systems. With its high charging and discharging capacity and support for various battery types, it is ideal for demanding energy projects.Highlights at a glanceHigh performance: 20 kW rated output for high energy requirements Flexible battery selectionCompatible with lead-acid and lithium-ion batteries High charging/discharging current: Up to 350A for fast power transmission Expandable: Parallel connection of up to 10 devices possible Robust designIP65 protection class for use in various environments Efficient energy conversion for modern requirementsThe Deye SUN-20K-SG05LP3-EU-SM2 is specially designed to meet the requirements of modern photovoltaic systems. With its three-phase output power and support for 48V low-voltage batteries, it offers an efficient solution for energy conversion and storage.Flexibility and scalabilityThanks to the option of connecting up to 10 devices in parallel, the inverter can be flexibly adapted to different system sizes. The support of both lead-acid and lithium-ion batteries enables customised adaptation to specific energy requirements.Reliability and protectionWith a protection class of IP65, the inverter is protected against dust and water, ensuring reliable operation in different environments. The integrated protective functions ensure safe and stable operation of the system.Who is the Deye SUN-20K-SG05LP3-EU-SM2 suitable for?This inverter is ideal for: Operators of larger solar systems who are looking for a flexible and safe storage solution Commercial enterprises that want to cover energy peaks or work off-grid Homeowners who want to maximise their self-consumption rate Users with diesel generator support who are aiming for maximum self-sufficiency  ModelSUN-20K-SG05LP3-EU-SM2 Battery input data Battery typeLead-acid or lithium-ion Battery voltage range (V)40~60V Max. Charging current (A)350A Max. Discharge current (A)350A Charging strategy for Li-ion batterySelf-adaptation to BMS Number of battery inputs2 Input data of the PV string Max. DC input power (W)32000W Max. DC input voltage (V)800V Starting voltage (V)160V MPPT voltage range (V)160V-650V Rated DC input voltage (V)550V Max. Operating PV input current (A)36+36A Max. Input short-circuit current (A)54+54A Number of MPP trackers/Number of MPP tracker strings2/2+2 AC input/output side Rated AC input/output effective power20000 Max. AC input/output apparent power22000 AC input/output rated current (A)30.4/29 Max. AC input/output current (A)33.4/31.9 Max. Continuous AC passthrough (mains for charging)70 Peak power (without mains)2x rated output power, 10s Setting range of the power factor0.8 leading to 0.8 trailing Nominal input/output voltage/range (V)220/380V, 230/400V 0.85Un-1.1Un Nominal input/output mains frequency/range(Hz)50/45-55, 60/55-65 Form of the mains connection3L+N+PE Total harmonic current distortion (THDi)<3% ( rated power ) DC current power supply<0.5% In Efficiency Max. Efficiency97,6% Euro efficiency97,0% MPPT efficiency>99% Protection of the devices IntegratedDC reverse polarity protection, AC output overcurrent protection, AC output overvoltage protection, AC output short-circuit protection, thermal protection, DC terminal insulation impedance monitoring, DC component monitoring, earth fault current monitoring, power grid monitoring, protection against islanding, earth fault detection, overvoltage load shedding protection, residual current monitoring (RCD), overvoltage category Overvoltage protection levelTYPE II(DC), TYPE II(AC) Interface Communication interfaceRS485/RS232/CAN Monitor modeGPRS/WIFI/Bluetooth/4G/LAN (optional) General data Operating temperature range (℃)-40 to +60°C, >45°C power reduction Permissible ambient humidity0-100% Permissible height3000m Noise (dB)<60 dB(A) Protection classIP 65 Inverter topologyNon-insulated Overvoltage categoryOVC II(DC), OVC III(AC) Dimensions (WxHxD mm)456×750×268.5 (without connectors and brackets) Weight (kg)51.9 Cooling modeIntelligent cooling Guarantee5-year/10-year warranty period depends on the installation conditions of the inverter. Details can be found in the general warranty conditions Mains regulationIEC 61727, IEC 62116, CEI 0-21, EN 50549, NRS 097, RD 140, UNE 217002, OVE guideline R25, G99, VDE-AR-N 4105 Safety EMC / StandardIEC/EN 61000-6-1/2/3/4, IEC/EN 62109-1, IEC/EN 62109-2  FAQs about the Deye Sun three-phase hybrid inverterWhich battery types are supported?The inverter is compatible with lead-acid and lithium-ion batteries in the voltage range from 40 to 60V.Can I operate several devices in parallel?Yes, up to 10 units can be operated in parallel, making the inverter ideal for larger systems.What is the maximum charging and discharging current?The maximum charging and discharging current is 350A each, which enables fast energy transfer.What is the standby consumption of the device?The Deye SUN-20K-SG05LP3-EU-SM2 has a self-consumption of ≤ 60 W.Does the 20 kW inverter fit on an 18 kWp system or do I have to oversize/undersize?Yes, the Deye SUN 20K-SG05LP3-EU-SM2 is technically optimised for an 18 kWp system. It does not necessarily have to be oversized or undersized. With a DC/AC ratio of around 0.9, it is exactly in the ideal range (0.9 - 1.1 is recommended). This means that the system is even slightly undersized, but this has practically no disadvantages and at the same time offers scope for retrofitting additional modules at a later date. Scope of delivery: Deye SUN-20K-SG05LP3-EU-SM2 (20 kW LV hybrid inverter) 1 x Deye SUN-20K-SG05LP3-EU-SM2 inverterAn extremely powerful three-phase hybrid inverter with 20 kW output, integrated LCD colour touchscreen and support for 48V low-voltage battery systems.1 x Wall Mount BracketA solid metal mounting rail for securely fastening the appliance to a load-bearing wall.1 x Wi-Fi stick (data logger)A plug-in communication module for connection to the internet for remote monitoring via Deye Cloud or Solarman app.3 x current transformer (CT)External hinged current transformers for measuring the energy flows at the house connection, necessary for zero feed-in and self-consumption optimisation.1 x set of PV connectors (MC4-compatible)The required pairs of DC plugs (plus and minus) for connecting the PV strings to the inverter.1 x communication cable (BMS)A pre-assembled RJ45 data cable for the connection between the inverter and the battery management system.1 x mounting set (screws and plugs)A set of stainless steel screws and heavy-duty dowels for professional installation of the wall bracket.1 x operating instructions (user manual)A printed manual with detailed installation instructions, circuit diagrams and safety instructions.

The Felicity Solar FLA48314-EU is a powerful 48V lithium iron phosphate storage (LiFePO4) system specially developed for efficient energy management in residential buildings and small commercial operations. With a gross capacity of 16.07 kWh this compact system offers impressive energy density and is the ideal choice for users who value safety, durability, and easy installation.Thanks to the low-voltage technology (48V/51.2V), the storage is compatible with a wide range of commonly available hybrid inverters. The robust construction and the intelligent battery management system (BMS) ensure that your photovoltaic system achieves maximum self-consumption and sustainably reduces your energy costs.Highlights at a glanceHigh storage capacity: With over 16 kWh capacity per unit, even larger households and heat pump systems can be reliably supplied overnight.Safe LiFePO4 chemistry: The lithium iron phosphate technology is extremely thermally stable and offers a lifespan of over 6000 cycles with high depth of discharge.Integrated smart BMS: Continuously monitors cell voltages, currents and temperatures to guarantee safe operation and uniform cell ageing.Broad compatibility: Works seamlessly with leading 48V inverters (e. g. Victron, Deye, Growatt, GoodWe), offering maximum flexibility in system selection.Scalable system: Up to 12 units can be connected in parallel to achieve total capacities of up to 192 kWh for commercial applications.Simple wall mounting: The compact design allows space-saving installation and neat wiring in the technical room or basement.Areas of applicationThe FLA48314-EU is versatile for modern energy concepts:Maximising self-consumptionStore your solar energy during the day to avoid expensive grid supply in the evenings and when it is cloudy.Emergency power & island solutions (off-grid)In combination with a suitable inverter, the storage ensures the power supply during grid failures or in remote areas.Retrofitting existing systemsIdeal for upgrading older PV systems with a modern, long-lasting 48V battery storage.Assembly & Safety InstructionsProfessional installationDue to the high capacities and currents, the connection must be carried out by a qualified electrician. Ensure sufficiently sized battery cables (cross-section).Site conditionsInstall the storage in a dry, well-ventilated place. The optimum operating temperature is between +15°C and +30°C to achieve maximum service life.Parallel connectionWhen expanding the system, ensure that all battery modules have the same software version and a similar state of charge (SOC) before connection. Features Model**Felicity Solar FLA48314-EU** Nominal energy**16.1 kWh** Nominal voltage**51.2 V** (low voltage) Nominal capacity314 Ah Battery typeLithium iron phosphate (LiFePO4) Max. charge/discharge current150 A (continuous) Parallel connectionUp to 12 units Degree of protectionIP21 (indoor installation) CertificationsCE, UN38.3, MSDS  FAQs about the Felicity Solar FLA48314-EUIs this storage compatible with my inverter?Usually yes.The FLA48314-EU supports the most common protocols for 48V systems. It is compatible with Victron Energy, Deye, Growatt, Voltronic and many other manufacturers. Please check Felicity Solar’s current compatibility list in advance.How many cycles does the battery last?Over 6000 cycles.At a depth of discharge of 80% (DoD) and proper handling, the LiFePO4 chemistry guarantees a service life of over 10 years, making it one of the most durable storage solutions on the market.Can I expand the capacity later?Yes.You can connect up to 12 units of the FLA48314-EU model in parallel. In this way, the system grows flexibly with your energy requirements, whether due to a new EV or an air conditioner.Does the storage require active cooling?No.The housing is designed for efficient passive heat dissipation. As a result, the storage operates completely silently, which is especially beneficial for installation in residential buildings.How safe is the LiFePO4 technology in the home?Very safe.Unlike conventional lithium-ion batteries (NMC), LiFePO4 cells are not flammable and are not prone to thermal runaway even in the event of damage or short circuit. They are considered the safest choice for home storage.  Scope of delivery: Felicity Solar FLA48314-EU (16.1 kWh LV battery storage) 1 x Felicity Solar FLA48314-EU battery moduleA standing 51.2V LiFePO4 energy storage with a capacity of 314 Ah (16.1 kWh) and integrated battery management system (BMS).1 x set of DC power cables (power cable)A pair of high-current cables (plus and minus) for electrically connecting the storage to the low-voltage inverter.1 x BMS communication cableA pre-assembled data cable (RJ45) for communication between the battery and the inverter via CAN or RS485 interface.1 x earth cableA yellow-green protective earth cable for safe earthing of the battery housing.1 x wall mounting kit / anti-tilt protectionMounting accessories for attaching the housing to the wall to prevent the standing storage from tipping over.1 x mounting kit (screws and accessories)All necessary small parts and screws for installation and electrical connections.1 x user manualA technical manual with installation instructions, pin assignments for various inverters, and safety instructions.

The Deye SUN-3.6K-SG05LP1-EU-AM2 is a compact, single-phase hybrid inverter designed specifically for smaller photovoltaic systems in residential buildings. With an AC output power of 3.6 kW it offers the ideal introduction to energy independence by combining solar power generation, battery management and emergency power supply in a single device.As part of the SG05 series this inverter is designed for operation with 48V low-voltage batteries optimised. This makes the system particularly flexible and cost-effective when selecting the storage unit. Despite its compact design, it features all the ‘major’ Deye features, such as the Smart Load connection and parallel scalability.Highlights at a glanceLow-voltage battery connection: Compatible with standard 48V lithium-ion and lead-acid batteries, offering a wide range of cost-effective storage options.Colour touchscreen LCD: Intuitive operation and real-time monitoring of all energy flows directly on the device via the integrated display.2 MPPT trackers: Enables the connection of two independent string arrays, ideal for roofs with different orientations (e.g. east-west).Excellent backup function: Lightning-fast switchover to emergency power in less than 10 ms, ensuring that sensitive equipment continues to run without interruption in the event of a mains failure.AC coupling possible: Existing solar systems can be easily integrated via the inverter to retrofit them with a storage unit.Parallel connection: Up to 16 units can be connected in parallel to flexibly increase system performance as demand rises.Smart load connection: The "Smart Load" port enables the targeted control of loads such as heating elements or pool pumps when there is a surplus of solar energy.Areas of applicationThe SUN-3.6K is the specialist for efficient small-scale systems:Detached houses & flatsPerfect for PV systems up to approx. 4.6 kWp, to drastically increase self-consumption in the household.RetrofittingAdd a 48V battery storage system to an existing installation without having to replace the old inverter.Critical infrastructureProtection for servers, aquariums or heating controls thanks to the reliable UPS function.Installation & Safety InstructionsBattery protectionAs high currents can flow in 48V systems, it is essential to ensure that the cable cross-sections are sufficiently sized and that a suitable DC fuse is installed between the battery and the inverter.Wall mountingThe device is robustly built and designed for wall mounting. Thanks to its IP65 protection rating, it can also be installed in sheltered outdoor areas.Earthing & lightning protectionEnsure that the system is properly earthed to protect the electronics and connected loads from power surges.. Features ModelDeye SUN-3.6K-SG05LP1-EU-AM2 Rated output power3.6 kW (3,600 watts) Phases1-phase (230V) Battery typeLow voltage (LV) 48V Li-Ion / Lead Number of MPP trackers2 MPPT Max. charging/discharging current90 A Max. efficiency97,60 % Protection classIP65** (weatherproof) Special featureIncludes **connection cable set  FAQs for the Deye SUN-3.6K-SG05LP1Which batteries are compatible with this inverter?Almost all 48V lithium storage systems.It is perfectly compatible with popular models such as Pylontech (US2000C/US3000C/US5000), Dyness or Deye’s own low-voltage batteries. Conventional lead-gel batteries can also be configured. It is essential to check the batteries against the compatibility list before purchasing.Can I use the inverter for a balcony power plant?Technically yes, but oversized.While it far exceeds the output of a balcony power plant, it offers the advantage that you can integrate a proper battery and later scale the system into a full roof-mounted installation.Is the Wi-Fi module for app control included?Usually, yes.Deye usually comes with a Wi-Fi dongle, which you can use to connect the system to the "Solarman" app or the Deye portal to view yields and consumption worldwide.Can the unit start a generator?Yes.Via the signal port, the inverter can send an automatic start command to compatible generators if the battery level is too low and there is no sunlight. Scope of delivery: Deye SUN-3.6K-SG05LP1-EU-AM2-P (3.6 kW single-phase hybrid inverter) 1 x Deye SUN-3.6K-SG05LP1-EU-AM2-P inverterA compact single-phase hybrid inverter with 3.6 kW output, an integrated colour LCD touchscreen and support for 48V low-voltage battery systems.1 x wall mount bracketA sturdy metal mounting rail for securely fixing the unit to a load-bearing wall.1 x Wi-Fi stick (data logger)A plug-in communication module for connecting to the internet for remote monitoring via the Deye Cloud or Solarman app.1 x current transformer (CT)An external folding current transformer for measuring energy flows at the property connection, necessary for net metering and optimising self-consumption.1 x set of battery connection cables (DC cables)A pair of pre-assembled high-performance cables (red and black) for direct electrical connection to a 48V battery (specific to this bundle version).1 x set of PV connectors (MC4-compatible)The required pairs of DC connectors (positive and negative) for connecting the PV strings to the inverter.1 x communication cable (BMS)A pre-assembled RJ45 data cable for connecting the inverter to the battery management system.1 x mounting kit (screws and wall plugs)A set of stainless steel screws and heavy-duty wall plugs for the correct installation of the wall mount.1 x User ManualA printed manual containing detailed installation instructions, circuit diagrams and safety instructions.

The Deye SUN-10K-SG01HP3-EU-AM2 is a state-of-the-art, three-phase high-voltage hybrid inverter, specially developed to maximise self-consumption and increase energy independence in residential and commercial properties. With a rated output of 10 kW combines the functions of a photovoltaic inverter, a battery charger and an off-grid system in a robust unit.The AM2 series is characterised by its compatibility with High-voltage battery systems which significantly increases system efficiency through lower conversion losses. Thanks to its extremely fast switchover time, it also functions as a fully-fledged uninterruptible power supply (UPS), continuing to supply critical loads within milliseconds in the event of a mains failure.Highlights at a glanceMaximum efficiency: Support for high-voltage batteries minimises transmission losses and optimises overall system performance.Genuine 3-phase emergency power: Provides a complete three-phase backup power supply with 100% unbalanced load capability in the event of a mains failure.DC and AC coupling: Versatile for upgrading existing solar systems (AC-side) or for complete new installations (DC-side).Intelligent load management: A dedicated "Smart Load" connection enables the targeted control of high-power consumers such as heat pumps or heating elements when there is a surplus of PV power.Robust IP65 housing: Suitable for indoor and outdoor installation, protected against dust and water jets.Advanced communication: Integrated interfaces for Wi-Fi/LAN monitoring as well as RS485/CAN for precise communication with BMS systems from leading battery manufacturers.Colour touchscreen LCD: Intuitive operation and direct visualisation of energy flows directly on the device.Areas of applicationHome optimizationIdeal for households with an electric car and a heat pump, enabling a significant increase in the share of solar power in total consumption.Commercial PV systemsUse in small commercial premises to reduce electricity costs and safeguard critical IT infrastructure.Agriculture & Stand-alone solutionsReliable power supply in regions with an unstable grid or for completely off-grid operation.Installation & Safety InstructionsBattery compatibilityBefore installation, please check the compatibility list at Deye. The inverter is optimised for high-voltage storage systems; 48V systems cannot be operated with this specific model.Ventilation & CoolingWhen wall-mounting, ensure there is sufficient clearance to the sides (min. 30 cm) and above/below (min. 50 cm) to ensure optimal heat dissipation.Surge protectionThe device features integrated Type II surge protection for DC and AC, which reduces installation costs and enhances safety. Features ModelDeye SUN-10K-SG01HP3-EU-AM2 Rated output power10 kW (10,000 watts) Phases3-phase (400V / 230V) Battery typeHigh-voltage (HV) Li-ion battery Battery voltage range160 V – 700 V Number of MPP trackers2 MPPT Max. efficiency97.60 % Protection classIP65 (suitable for outdoor installation) Special featureColour touchscreen & capable of black start  FAQs for the Deye SUN-10K-SG01HP3-EU-AM2Can the inverter be connected in parallel?Yes, up to 10 devices. For higher power requirements, multiple units can be connected in parallel to scale both the AC power and the battery capacity.Does the device support zero-feed-in?Yes, fully configurable. Using the included smart meter or CT clamps, the inverter can be configured to ensure no electricity is fed into the public grid (zero-export function). The manufacturer should be contacted regarding configuration. It is also necessary to discuss this with the network operator.Is the Wi-Fi module included in the scope of delivery?Yes, a logger is usually included. The inverter is supplied as standard with a Wi-Fi stick (LSW-3), which enables easy connection to the Solarman app. Scope of delivery: Deye SUN-10K-SG01HP3-EU-AM2 – 10 kW / 3-phase hybrid inverter 1 x Deye SUN-10K-SG01HP3-EU-AM2 inverterA three-phase high-voltage hybrid inverter with 10 kW output, an integrated LCD touchscreen and two MPPT trackers.1 x wall mount bracketA sturdy metal mounting rail for securely fixing the unit to the wall.1 x Wi-Fi plug / data loggerA plug-in communication module for connecting to the internet for remote monitoring via the Deye Cloud or Solarman app.3 x current transformers (CT - Current Transformer)External sensors for the precise measurement of energy flow at the property connection point, which are required for zero-export and self-consumption control.1 x set of PV connectors (MC4-compatible)The corresponding pairs of DC connectors (positive and negative) for connecting the solar modules to the inverter.1 x set of battery connectorsSpecial high-voltage connectors for the safe electrical connection of a compatible battery storage unit.1 x communication cable (BMS)A pre-assembled RJ45 data cable for communication between the inverter and the battery management system.1 x mounting kit (screws and wall plugs)A set of stainless steel screws and heavy-duty wall plugs for the correct installation of the wall mount.1 x User ManualA printed manual containing detailed circuit diagrams, installation instructions and safety instructions.

The Deye SUN-8K-SG05LP1-EU-AM2-P is a high-performance, single-phase hybrid inverter, specially developed to meet the requirements of modern households with high energy demands. With an impressive rated output power of 8 kW it is one of the most powerful single-phase units in its class and enables comprehensive optimisation of self-consumption as well as a seamless emergency power supply.The "P" series is intended for use with high-current PV modules optimised. Thanks to an increased input current of up to 26 A per MPPT, state-of-the-art solar panels with large cell formats and high yields can be efficiently integrated. As a low-voltage hybrid, the device operates with 48 V batteries combined, allowing for flexible and cost-effective scaling of the storage system.Highlights at a glanceImpressive 8 kW single-phase power: Ideal for households with high loads that require strong single-phase protection or high charging power for batteries.High-current PV inputs (26 A): Perfectly matched to the latest generation of high-performance modules to maximise solar yields.48 V low-voltage system: Fully compatible with a wide range of affordable and modularly expandable 48 V battery storage systems (e.g. LiFePO4 from Deye or Pylontech).High charging/discharging current (190 A): Enables rapid charging of large storage capacities and the powering of energy-intensive devices directly from the battery.Genuine emergency power output (UPS): Switches to island mode in less than 4 ms in the event of a mains failure, ensuring that even sensitive electronics are protected without interruption.2 MPPT trackers: Offers flexibility in roof coverage and optimises yield for different orientations or partial shading.Smart Load & AC-Coupling: Surplus energy can be specifically used for consumers such as heat pumps; furthermore, existing inverters can be easily integrated.Areas of applicationLarge detached housesMaximising self-sufficiency by combining high PV output with large, cost-effective 48 V storage systems.Backup & stand-alone solutionsThanks to its high output of 8 kW, it is ideally suited for off-grid systems or for providing full backup during critical periods in regions with an unstable grid.RetrofitCan be installed in parallel with existing solar systems via AC coupling to enhance them with a high-performance storage function.Installation & safety instructionsBattery wiringDue to the 48 V technology and currents of up to 190 A, large cable cross-sections (e.g. 2x 50 mm² or 70 mm²) and high-quality DC fuses are absolutely essential.VentilationThe device is equipped with active fan cooling. Install the inverter in a cool, well-ventilated location and observe the specified minimum clearances.Phase balancingWhen operating on a 3-phase mains supply (e.g. Germany), a smart meter is required at the grid connection point to mathematically balance the consumption of all phases (balancing). Features ModelDeye SUN-8K-SG05LP1-EU-AM2-P Rated output power8.0 kW (8,000 watts) Phases1-phase (230V) Battery typeLow voltage (LV)** 48V Li-Ion / Lead Number of MPP trackers2 MPPT Max. charging/discharging current190 A Max. efficiency97,60 % Protection classIP65 (weatherproof) Special featureColour touchscreen & Smart Load  FAQs for the Deye SUN-8K-SG05LP1-EU-AM2-PCan I operate a heat pump with this device?Yes, no problem. Thanks to the high output power of 8 kW and the Smart Load function, the inverter can be configured to prioritise supplying the heat pump with surplus solar energy.Is operation without a battery possible?Yes, the device also starts without storage. The inverter can be used as a pure PV inverter. A 48 V storage unit can be added later at any time via plug-and-play to increase self-consumption.Does the device support zero feed-in?Yes, via the supplied sensor. Using the CT clamp or a smart meter, the feed-in to the public grid can be limited to 0 watts (zero export). The manufacturer should be contacted regarding configuration. It is also necessary to discuss this with the grid operator. Scope of delivery: Deye SUN-8K-SG05LP1-EU-AM2-P (8 kW single-phase hybrid inverter) 1 x Deye SUN-8K-SG05LP1-EU-AM2-P inverterA high-performance single-phase hybrid inverter with 8 kW output, integrated LCD colour touchscreen and support for 48V low-voltage battery systems.1 x wall mount bracketA sturdy metal mounting rail for securely fixing the device to a load-bearing wall.1 x Wi-Fi stick (data logger)A plug-in communication module for connecting to the internet for remote monitoring via Deye Cloud or the Solarman app.1 x current transformer (CT - current transformer)An external clip-on current transformer for measuring energy flows at the house connection, necessary for zero feed-in and self-consumption optimisation.1 x set of battery connection cables (DC cables)A pair of pre-assembled high-performance cables for the direct electrical connection of a 48V battery (specific to this "P" bundle version).1 x set of PV connectors (MC4-compatible)The required pairs of DC connectors (positive and negative) for connecting the PV strings to the inverter.1 x communication cable (BMS)A pre-assembled RJ45 data cable for the connection between the inverter and the battery management system.1 x mounting set (screws and wall plugs)A set of stainless steel screws and heavy-duty wall plugs for the professional installation of the wall bracket.1 x operating manual (user manual)A printed manual with detailed installation instructions, circuit diagrams and safety information.

The Deye SE-F12 is a state-of-the-art low-voltage energy storage system (48V / 51.2V) designed for maximum reliability and performance in residential and commercial solar installations. With an impressive rated capacity of 11.8 kWh (approx. 230 Ah) in a single, compact housing, this storage unit offers an excellent balance of high energy density and proven safety.Thanks to the long-lasting lithium iron phosphate (LiFePO4) cell chemistry and the intelligent battery management system (BMS), the SE-F12 is the ideal choice for users who wish to maximise their self-sufficiency. The system’s enormous scalability also makes it a flexible and future-proof investment in your own energy independence.Highlights at a glanceHigh storage capacity (11.8 kWh): It offers a massive 230 Ah at a nominal voltage of 51.2 V in a single module, which drastically reduces the amount of cabling required compared to smaller 5 kWh blocks.Safe LiFePO4 technology: It uses lithium iron phosphate, the safest and most thermally stable cell chemistry on the market, with no risk of thermal runaway.Powerful power handling: Enables a maximum continuous discharge current of 230 A (approx. 11.5 kW output) and peak currents of up to 280 A for 10 seconds – ideal for large consumers such as heat pumps or electric car charging stations.Extreme scalability: The system scales with your requirements. Up to 32 units can be connected in parallel as standard (with a CAN-Bridge, up to 64 units for a storage capacity of up to 18 MWh).Smart monitoring: Equipped with LED status indicators as well as Bluetooth, RS485 and CAN2.0. Seamless integration in the Deye app enables precise real-time monitoring on your smartphone.Long service life: Certified for over 6,000 cycles (at 80 % depth of discharge / DoD), which corresponds to a service life of 15+ years with daily charging and discharging.Flexible installation: Certified to IP21, the housing supports both wall mounting and floor-standing (stacked) installation to make optimum use of space in the plant room.Areas of applicationThe Deye SE-F12 is extremely versatile and is primarily suitable for:Detached houses: To maximise self-consumption and as a robust emergency power storage solution in combination with hybrid inverters.Commercial systems (C&I): For peak shaving and the storage of large PV yields in agricultural or commercial operations.Off-grid systems: The high continuous load capacity easily serves stand-alone off-grid systems with large inrush currents.Installation & safety instructionsTransport and handling: With a weight of 84 kg the module is extremely heavy. Be sure to plan transport into the basement or plant room with two people or suitable lifting equipment (e.g. stair climber).Temperature management: The storage unit operates within a wide range (-20°C to 55°C during discharge), but should be installed in a frost-free, dry room (15°C to 25°C) for maximum service life and capacity yield. Charging below 0°C is blocked by the integrated BMS for safety reasons.Cable sizing: To transmit the enormous maximum continuous current of 230 A without voltage losses or dangerous heat build-up, high-quality battery cables with a cross-section of at least 70 mm² (better 95 mm²) between the storage unit and busbar or inverter are essential.Compatibility: The system "speaks" the Deye protocol natively and works best via Plug & Play with Deye low-voltage hybrid inverters (e.g. the SUN-10K or 12K-SG04LP3 series). Features  ModelDeye SE-F12 Technology**LiFePO4** (lithium iron phosphate) Rated voltage**51.2 V** (operating range: 44.8 V - 57.6 V) Rated capacity**230 Ah** Nominal energy**11.8 kWh** Max. continuous current**230 A** (peak current 280 A for 10s) Cycle life**≥ 6000 cycles** (at 80% DOD and 25°C) CommunicationCAN 2.0 / RS485 / Bluetooth + app connectivity Dimensions (W x D x H)approx. 400 x 232 x 583 mm Weightapprox. **84 kg** Installation typeFloor mounting, wall mounting or stacked  FAQs on the Deye SE-F12Can I use this battery with an inverter from another brand?In principle, yes. The Deye SE-F12 uses standard communication protocols (CAN/RS485) and can often also be operated with compatible third-party brands. However, the correct BMS protocol on the battery must be configured manually (via software or DIP switch). There is no support for this third-party use during setup from the manufacturer or retailer. A functioning system can only be guaranteed with the Deye own brand. Please compare the compatibility list in advance.What happens in the event of a power cut in the house?If you combine the SE-F12 with a hybrid inverter capable of emergency power supply (such as the Deye SG04 series), the system switches to battery operation within milliseconds in the event of a grid failure. Thanks to the high discharge power (up to 11.5 kW from just one battery), you can continue to supply even large 3-phase loads in the house grid without problems.Why do some shops list "SE-F12-C"?The suffix "-C" generally denotes the latest model revision (often the EU version), which is equipped with an integrated LCD display on the front of the housing. This allows cell voltages and SoC to be read directly. The pure performance data compared to the standard SE-F12 are identical.

The Felicity Solar FLA 48460TG2-EU is a giant among home storage systems. With an enormous capacity of 23.5 kWh in a single housing, this 48V block redefines what a powerful all-in-one storage system can achieve. Instead of many small modules, you get a massive energy storage unit for maximum autonomy. This floor-mounted solution is based on safe LiFePO4 technology and is aimed at large PV systems, multi-family houses or commercial use. The TG2 version also offers modern features such as integrated WiFi/Bluetooth for real-time monitoring and an aerosol fire extinguishing system. Highlights at a glanceGigantic capacity (23.5 kWh / 460 Ah): A single block stores an extremely large amount of energy and reduces space requirements, wiring and installation effort. High performance (up to 12.5 kW): Designed for 250A continuous charge/discharge current and 500A peak (15s) – ideal for high loads and powerful hybrid systems. Monitoring integrated (WiFi/Bluetooth): Real-time monitoring of status, performance and system data directly via wireless connection. LiFePO4 cell chemistry: Lithium iron phosphate is considered particularly thermally stable and safe for stationary storage systems. Safety setup: Integrated Smart-BMS as well as breaker & fuse; additionally aerosol fire extinguishing system. External fuse (easy replacement): The external fuse design allows for service-friendly replacement. Scalable up to 15 units: Parallel connection of up to 15 storage units (up to 352.5 kWh) for large systems. Long service life: Designed for ≥ 6000 cycles (Test condition: 25°C ±2°C, 0.5C/0.5C, 90% DoD, 70% EOL). Areas of applicationThe FLA 48460TG2-EU is the solution for power users and large consumers: Maximum autonomy: More energy at home, less grid consumption – even in bad weather.Commercial & multi-family houses: High capacity and power reserve for demanding load profiles.Backup systems: High continuous output for emergency/back-up power scenarios (note system design).Scalable storage parks: Up to 15 units in parallel for very large capacities.Installation & safety instructionsLogistics & weight: Product weight approx. 186.5 kg (packaging weight approx. 220 kg). Delivery is typically on a pallet/forwarding agent. Suitable lifting/transport equipment must be planned for bringing in. Installation location: Floor-mounted. The surface must be level and load-bearing. Dimensions: 570 x 250 x 980 mm (W x D x H). Cable cross-section: For possible currents up to 250A, large cross-sections are usual. Please design the cross-section/protection according to standards, cable length and manufacturer specifications. Properties ModelFelicity Solar FLA 48460TG2-EU TechnologyLiFePO4 (Lithium iron phosphate) Nominal voltage51.2 V Energy content23.5 kWh Operating voltage44.8 – 57.6 V Max. continuous current (charge/discharge)250 A (depends on temperature & SOC) Peak current (15s)500 A Max. charge/discharge power12,500 W Depth of discharge (DoD)≥ 95% CommunicationRS485 / CAN Protection typeIP21 Cycles lifetime≥ 6000 (25°C ±2°C, 0.5C/0.5C, 90% DoD, 70% EOL) Temperature range charging0°C to +55°C Temperature range discharging-20°C to +55°C DisplayLCD + LED MountingFloor-mounted (Floor-Mounted) Protection / ComponentsSmart BMS, Breaker, Fuse (integrated) Warranty10 years CertificationUN38.3 Weight186.5 kg (product) / 220 kg (packed) Dimensions (W x D x H)570 x 250 x 980 mm FAQs for the Felicity FLA 48460TG2-EUHow long does it take to charge this battery?That depends on the available charging power of your inverter. With high charging power, the storage unit can be filled very quickly: At up to 12.5 kW (theoretical maximum), in practice this often corresponds to around about 2 hours for a full charge – depending on SOC, temperature and system limitations. Can I connect two of them in parallel?Yes. The storage unit is designed for parallel connection. With two units you get approx. 47 kWh capacity. In total, up to 15 units are possible in parallel (up to 352.5 kWh). How does the battery communicate with the inverter?Via CAN or RS485. Please check the compatibility and the necessary pin assignment/protocol selection in the documentation of your inverter.  Scope of delivery: Felicity Solar FLA 48460TG2-EU (23.5 kWh LV battery storage) 1 x Felicity Solar FLA 48460TG2-EU battery moduleA massive upright 51.2V LiFePO4 energy storage with a high capacity of 460 Ah (23.55 kWh) and integrated battery management system (BMS).1 x set of DC power cables (power cable)A pair of high-current cables (plus and minus) for electrical connection of the storage unit to the low-voltage inverter.1 x BMS communication cableA pre-assembled data cable (RJ45) for communication between the battery and the inverter via CAN or RS485 interface.1 x earthing cableA yellow-green protective earthing cable for safe earthing of the robust metal housing.1 x wall mounting set / anti-tilt deviceSpecial mounting accessories for attachment of the housing to a stable wall to prevent the heavy storage unit from tipping over.1 x mounting kit (screws and accessories)All required small parts, screws and connectors for professional mechanical and electrical installation.1 x user manual (User Manual)A technical manual with detailed installation instructions, pin assignments for communication and safety instructions.

The Deye SE-F16 is a high-capacity low-voltage energy storage system (51.2 V) designed for demanding use in residential and commercial photovoltaic systems. With an enormous rated capacity of 16 kWh (314 Ah) in just one compact housing module, this storage system significantly minimises the space required and the installation effort.This model uses the proven and intrinsically safe lithium iron phosphate (LiFePO4) cell chemistry. Combined with the intelligent Battery Management System (BMS) and a wide range of monitoring options (including Bluetooth), the SE-F16 offers maximum safety, scalability and longevity for the self-sufficient energy supply of your home or business.Highlights at a glanceMassive storage capacity (16 kWh): With a rated capacity of 314 Ah at 51.2 V, this single module provides enough energy to reliably supply large households even during prolonged periods of low sunlight.Safe LiFePO4 cell chemistry: The lithium iron phosphate technology guarantees maximum thermal stability and virtually eliminates the risk of thermal runaway (fire hazard).Powerful power handling: The system supports an enormous continuous discharge current of up to 230 A and peak currents of 280 A (for 10 seconds), ideal for power-hungry large loads such as heat pumps or wallboxes.Extreme scalability: For even greater energy requirements, up to 32 units can be connected in parallel as standard. With a CAN bridge, scaling up to 64 modules is even possible.Smart monitoring & connectivity: In addition to CAN2.0 and RS485, the storage system features Bluetooth for convenient monitoring via smartphone app. The "C" version (SE-F16-C) also has an integrated LCD display.Longevity & efficiency: Certified for over 6,000 charge cycles (at 25°C), ensuring decades of reliable operating life in daily use.Flexible installation: Despite the high weight, the housing system is extremely flexible and can be installed either on the wall, floor-standing or stacked.ApplicationsThe Deye SE-F16 is the perfect solution for demanding energy scenarios:Single-family and multi-family houses: Maximises self-consumption of PV power and, in combination with a hybrid inverter, provides a powerful emergency power supply for the entire building.Commercial applications (C&I): Used to cap expensive peak loads (peak shaving) and stores large PV surpluses in agricultural or commercial businesses.Off-grid & stand-alone systems: Thanks to its gigantic capacity and high continuous discharge power, it offers a reliable energy source for completely off-grid properties.Installation & safety instructionsLogistics and weight: At a weight of 109 kg, the module is extremely heavy. Installation should обязательно be carried out with suitable lifting equipment (stair climber) or by at least two to three people.Choice of location: The storage system must be installed in a dry and ideally frost-free room (protection class IP21). Charging at temperatures below 0°C is automatically blocked by the BMS to protect the cells.Cable cross-sections: Due to the extremely high currents (up to 230 A continuous load), the connection cables to the inverter or busbar must have a cross-section of at least 70 mm², preferably 95 mm², in order to avoid overheating and voltage losses.Commissioning with parallel connection: If you connect several SE-F16 modules together, all units must be charged to exactly the same voltage level before cabling in order to prevent dangerous equalisation currents. Features  ModelDeye SE-F16 (C series with display) Technology**LiFePO4** (lithium iron phosphate) Rated voltage**51.2 V** (operating range: 44.8 V - 57.6 V) Rated capacity**314 Ah** Nominal energy**16.0 kWh** Max. continuous current**230 A** (peak current 280 A for 10s) Cycle life**≥ 6000 cycles** (at 90% DOD and 25°C) CommunicationCAN 2.0 / RS485 / Bluetooth + app (incl. LCD display) Dimensions (W x D x H)approx. 400 x 233 x 708 mm Weightapprox. **109 kg** Mounting typeFloor mounting, wall mounting or stacked  H2: FAQs about the Deye SE-F16What is the difference between the SE-F16 and the SE-F12?The main difference lies in the capacity and the housing height. The SE-F16 delivers 16 kWh (314 Ah) and weighs around 109 kg, while the SE-F12 11.8 kWh (230 Ah) offers and weighs approx. 84 kg. Both use the same 51.2V architecture and are designed for identical applications, but the F16 offers significantly more autonomy per installed module.What does the "C" in the designation SE-F16-C mean?The suffix "-C" in Deye storage systems indicates the extended model variant which, in addition to Bluetooth monitoring, is also equipped with an integrated LCD display on the front of the housing. This allows the current state of charge (SoC), cell voltages and warning messages to be read directly on the device without having to open the app.Do I absolutely need a Deye inverter for this battery?No, but it is strongly recommended for smooth operation. The SE-F16 is "Plug & Play" compatible with Deye low-voltage hybrid inverters (such as the SG04 series), since the BMS protocol matches natively. With third-party brands (such as Victron, SMA or Solis), communication must first be configured manually via DIP switches or software settings. It is strongly recommended to check the compatibility list, as changes may occur on the manufacturer side.

The Deye GB-L-PRO20 is a powerful and highly flexible high-voltage energy storage system, specially developed for modern photovoltaic systems in residential and small commercial settings. With a gross capacity of 20.45 kWh offers a massive energy reserve to maximise independence from the public grid and reliably supply even large households or commercial premises.The system is supplied including the GBL-PRO BMS supplied, which acts as an intelligent control unit monitoring the entire tower. Thanks to the advanced lithium iron phosphate technology (LiFePO4) the system guarantees maximum safety whilst offering a long service life. The simple stackable design allows for quick installation without complex cable connections between the modules.Highlights at a glanceHigh safety: The cobalt-free LiFePO4 chemistry ensures maximum safety, thermal stability and a long cycle life of over 6,000 cycles.Central GBL-PRO BMS: The intelligent control unit monitors each cell individually and protects the entire system against overcharging, deep discharge and thermal issues.Easy installation: Thanks to the modular "plug-and-play" design, stacking assembly is quick and requires no additional cable connections between the battery modules.Efficient high-voltage technology: The high system voltage reduces conversion losses and optimises efficiency in combination with modern hybrid inverters.Emergency power capable: Supports high discharge rates to safely supply critical loads or entire households even during power cuts.Robust design: With an IP65 protection rating, the system is dust-tight and protected against water jets, enabling installation in a variety of environments.Areas of applicationThe GB-L-PRO20 is the ideal storage solution for sophisticated energy concepts:Self-consumption optimisationStorage of surplus solar power during the day for use in the evening and at night, even with high baseline consumption.Back-up power supplyWhen used in conjunction with compatible hybrid inverters, the system provides protection against power cuts (blackout protection) for the entire house.Peak shavingReduction in electricity costs through the buffering of peak loads, particularly in households with multiple electric charging points or heat pumps.Installation & safety instructionsSite selectionPlace the storage unit on a level, load-bearing surface (note the weight). Ensure adequate ventilation and observe the recommended minimum clearances.Protection against extreme temperaturesAlthough the system is designed for a wide temperature range, installation in cool, frost-free indoor areas (e.g. a basement or utility room) extends the service life of the cells.Professional commissioningThe electrical connection to the inverter and the configuration of the GBL-PRO BMS must only be carried out by certified specialist personnel. Features ModelDeye GB-L-PRO20 Nominal energy20.45 kWh Nominal voltage512 V (high voltage) Battery typeLithium iron phosphate (LiFePO4) Max. charge/discharge current50 A Usable energy (90% DoD)18.41 kWh Protection ratingIP65 (indoor/outdoor installation) Cycle life≥ 6000 cycles (@25°C, 90% DoD) CertificationsCE, IEC62619, VDE2510-50, UN38.3  FAQs about the Deye GB-L-PRO20 battery systemCan I expand the system later with additional modules?Yes.Thanks to the modular design, you can flexibly scale the capacity of your storage system. The GBL-PRO BMS automatically detects new modules and integrates them into battery management.Which inverters is the system compatible with?Primarily with Deye hybrid inverters.The system is optimally matched to Deye's high-voltage hybrid inverters. Please check the current compatibility list for third-party suppliers before installation.Why is LiFePO4 used as the cell chemistry?For superior safety.Unlike conventional lithium-ion batteries (NMC), LiFePO4 is chemically much more stable. Even if mechanically damaged, these cells do not tend to catch fire.Does the system have integrated heating for winter operation?Yes, optionally.The Deye GB-L-PRO20 system supports an integrated heating function that enables the battery cells to be safely charged even at low ambient temperatures. This effectively protects the cells in installations in unheated rooms.What is the maximum discharge power of the 20.45 kWh system?Depending on the module configuration.Thanks to high-voltage technology, the system can deliver high discharge currents. As a rule, this 20.45 kWh pack enables a continuous power output of approx. 10 kW to 15 kW, ideal for operating wall boxes or air conditioning systems. Scope of delivery Deye GB-L-PRO20 modular high-voltage battery system (20.45 kWh): System compositionThis product is a set and consists of six separate main components which together form a 20.45 kWh high-voltage tower system.Component 1: Deye GBL-PRO BMS (high-voltage control unit & base)The central control unit (BMS) that manages the entire high-voltage system. This unit forms the base of the battery tower.Components 2 to 6: Five Deye GB-L-PRO-BATT high-voltage battery modules (4.09 kWh each)Five high-voltage battery modules, each with 4.09 kWh, which are stacked onto the BMS unit and on top of one another.1 x set of battery connection cables (positive & negative)A pair of special high-voltage power cables for connecting the BMS unit to a compatible high-voltage hybrid inverter.1 x communication cable (CAN/RS485)A data cable for communication between the BMS and the inverter.4 x connecting bridge / series connection cableShort, robust cables or fixed bridges for connecting the five battery modules in series.1 x earthing cableA protective earth conductor cable for compliant earthing of the BMS unit.1 x mounting accessories (tower assembly)Includes screws or locking elements for securely connecting the six components into a tower.1 x operating and installation manualA printed manual describing the installation of the entire high-voltage tower system.

The Deye GB-L-PRO8 is a powerful and highly flexible high-voltage energy storage system, specially developed for modern residential photovoltaic systems. With a gross capacity of 8.18 kWh offers a reliable solution for maximizing self-consumption and sustainably increasing independence from the public grid.The system stands out thanks to its modular design and advanced Lithium iron phosphate technology (LiFePO4), which guarantees maximum safety and a long service life. Thanks to its simple stackable design, the system can be installed without complex cabling between the modules and easily expanded as required.Highlights at a glanceHigh safety: The cobalt-free LiFePO4 chemistry ensures maximum safety, thermal stability and a long cycle life.Easy installation: Thanks to the modular "plug-and-play" design, stacking assembly is quick and requires no additional cable connections between the battery modules.Integrated BMS: The intelligent battery management system monitors each cell individually and protects against overcharging, deep discharge and extreme temperatures.Efficient high-voltage technology: The high system voltage reduces conversion losses and optimises efficiency in combination with modern hybrid inverters.Emergency power capable: Supports high discharge rates to ensure a safe supply to critical household appliances even during power cuts.Robust design: With an IP65 protection rating, the system is dust-tight and protected against water jets, enabling installation in a variety of environments.Areas of applicationThe GB-L-PRO8 is the ideal storage solution for compact and efficient energy concepts:Self-consumption optimisationStorage of surplus solar power during the day for use in the evening and at night.Back-up power supplyWhen used with compatible hybrid inverters, the system provides protection in the event of power cuts (blackout protection).Peak shavingReduction in electricity costs through the buffering of peak loads, particularly in households with heat pumps or electric vehicle charging points.Installation & Safety InstructionsSite selectionPlace the storage unit on a level, load-bearing surface. Ensure adequate ventilation and maintain the recommended minimum distances from walls.Protection against extreme temperaturesAlthough the system is designed for a wide temperature range, installation in cool, frost-free indoor areas (e.g. a basement or utility room) extends the service life of the cells.Professional commissioningThe electrical connection to the inverter and the configuration of the BMS must only be carried out by certified specialists in order to maintain the warranty. Features  ModelDeye GB-L-PRO8 Rated energy8.18 kWh Rated voltage204.8 V (high voltage) Battery typeLithium iron phosphate (LiFePO4) Max. charging/discharging current50 A Usable energy (90% DoD)7.2 kWh Protection classIP65 (indoor/outdoor installation) Cycle life≥ 6000 cycles (@25°C, 90% DoD) CertificationsCE, IEC62619, VDE2510-50, UN38.3  FAQs on the Deye GB-L-PRO8 battery systemCan I expand the system with additional modules at a later date?Yes.Thanks to the modular design, you can flexibly scale the capacity of your storage system to meet growing energy demands by adding compatible battery modules.Which inverters is the system compatible with?Primarily with Deye hybrid inverters.The system is optimally matched to the high-voltage hybrid inverters from Deye. Please check the current compatibility list for third-party manufacturers before installation.Why is LiFePO4 used as the cell chemistry?For superior safety.Unlike conventional lithium-ion batteries (NMC), LiFePO4 is chemically much more stable. Even if physically damaged, these cells do not tend to catch fire, making them the safest choice for residential buildings.Does the system have an integrated heating system for winter operation?Yes, optional.The Deye GB-L-PRO8 system supports an integrated heating function, which enables the battery cells to be charged safely even at low ambient temperatures. This is particularly important for installations in unheated rooms to prevent cell damage in freezing conditions.What is the maximum discharge power of the 8.18 kWh system?Depending on the module configuration.Thanks to high-voltage technology, the system can deliver high discharge currents. Typically, this 8.18 kWh pack enables a continuous power output of approx. 4 kW to 6 kW, ideal for operating standard household appliances during a power cut. Scope of delivery Deye GB-L-PRO8 Modular high-voltage battery system (8.18 kWh) System compositionThis product is a set and consists of three separate main components, which together form an 8.18 kWh high-voltage tower system.Component 1: Deye GB-L-PRO-BMS (high-voltage control unit & base)The central control unit (BMS) that manages the entire high-voltage system. This unit forms the base of the battery tower.Components 2 & 3: Two Deye GB-L-PRO-BATT high-voltage battery modules (4.09 kWh each)Two high-voltage battery modules, each with 4.09 kWh, which are stacked on the BMS unit.1 x set of battery connection cables (positive & negative)A pair of special high-voltage power cables for connecting the BMS unit to a compatible high-voltage hybrid inverter.1 x communication cable (CAN/RS485)A data cable for communication between the BMS and the inverter.1 x connecting bridge / series connection cableShort, robust cables or a fixed bridge to connect the two battery modules in series.1 x earthing cableA protective earth cable for the compliant earthing of the BMS unit.1 x installation accessories (tower assembly)Includes screws or locks to securely connect the three components into a tower.1 x operating and installation manualA printed manual describing the installation of the entire high-voltage tower system.

The Felicity Solar FLH96050SG01 in the version with 15.36 kWh is a performance-optimised high-voltage battery storage system for homes and businesses with high energy requirements. By combining three stacked 5.12 kWh modules, this system offers an enormous storage capacity, ideally suited to running heat pumps, overnight charging of electric vehicles, or bridging long periods of poor weather. Thanks to modern LiFePO4 technology and modular tower design, it combines safety, efficiency, and space savings.Highlights at a glanceMassive capacity: With 15.36 kWh usable capacity, this storage offers enough reserves for large households and maximises the degree of self-sufficiency of your PV system.Modular stack system: Consists of three battery modules and one control unit that wirelessly plug together (“Plug & Play”), simplifying installation.Maximum safety: Each module features an integrated aerosol fire suppression system and a multi-stage battery management system (BMS) for continuous monitoring of the cells.High-voltage efficiency: The higher system voltage ensures lower conversion losses and more efficient supply for high-power loads compared to low-voltage systems.Long service life: Uses high-quality lithium iron phosphate cells (LiFePO4) with over 6000 cycles at high depth of discharge (DOD).Wide compatibility: Seamless communication with common hybrid inverters (e.g. Deye, Growatt, Solis, GoodWe) via CAN/RS485 interfaces.Maximum independence for your homeWith 15.36 kWh, this storage system is in a performance class that far exceeds standard. It is the perfect solution for the energy transition at home (“sector coupling”). During the day it stores surplus solar power, which in the evening and at night is available for energy-intensive uses like cooking, the heat pump, or the EV charger. This minimises costly grid import to a minimum.Flexibility and expandabilityThe system grows with your needs. If your electricity demand increases in the future (e.g. due to a second EV), the storage tower can be expanded simply by adding more modules (depending on the maximum input voltage of the inverter). The smart BMS recognises new capacities and automatically integrates them into the system. Characteristics ModelFelicity Solar FLH96050SG01 (15.36 kWh system) ApplicationHigh-voltage storage system for PV installations (home storage) TechnologyLiFePO4 (Lithium iron phosphate) Nominal energy15.36 kWh Nominal voltage307.2 V Module capacity50 Ah Voltage range273.6 V - 345.6 V Charge/discharge current25 A (Recommended) / 50 A (Maximum) CommunicationCAN, RS485 Protection ratingIP65 (Dust-tight and protected against water jets) ExpandabilityModular construction (Stackable) Weight (kg)approx. 160 (complete system)  FAQs for the Felicity FLH96050SG01 (15.36 kWh)Who is the 15.36 kWh version suitable for?This size is ideal for detached houses with an annual electricity consumption of over 5,000 kWh or households actively using sector coupling (heat pump + EV). It allows a significant share of demand to be covered from the storage system even on cloudy days or in winter.How heavy is the system during installation?The total system weighs over 160 kg. However, thanks to the modular design, you do not need to move the full weight at once. Each individual battery module (about 50 kg each) and the control unit are stacked one after the other at the installation site.Is the storage suitable for outdoor use?The housing has protection rating IP65, i.e. it is dust-tight and protected against water jets. Installation in a garage, carport or beneath a canopy is therefore possible. However, to maximise the life of the cells, we recommend a location protected from direct sunlight and extreme frost (e.g. cellar or utility room).Can the system supply emergency power?Yes, the Felicity high-voltage storage can provide high discharge power. In combination with an emergency power capable hybrid inverter (with grid switching), the system can continue to supply the home grid in the event of a power failure. Scope of delivery: Felicity Solar FLH96050SG01 (15.36 kWh HV battery storage set) 1 x Felicity FLH96050SCG01 BMS control unitThe central high-voltage management module which monitors the cells and communicates with the inverter.3 x Felicity FLH48100-S battery modules (each 5.12 kWh)Three stackable high-voltage LiFePO4 storage units, connected in series to achieve the total capacity of 15.36 kWh.1 x Base plate (Base)A stable base for floor mounting on which the three battery modules and the control unit are safely stacked.1 x Set of internal connection cables (Plug & Play)Short plug connectors for electrical coupling and data transfer between the individual battery modules within the tower.1 x Set of external high-voltage cables (DC)A pair of specialist power cables for safe connection of the battery tower to the high-voltage hybrid inverter.1 x Communication cable (BMS-to-inverter)A pre-assembled data cable for connecting the control unit to the inverter (CAN/RS485).1 x Mounting kit (tip-over protection & screws)All fixtures for wall-mounting the tower and screws for mechanical module joining.1 x User manualA technical user guide with instructions for stacking, BMS configuration, and important safety information for high-voltage systems.

The Felicity Solar FLH96050SG01 with 25.6 kWh storage capacity is the most powerful single configuration of this high-voltage series and marks the top of home storage solutions. This system, consisting of a tower with five battery modules, offers massive energy reserves for large detached houses, multi-family houses or commercial applications. With a nominal voltage of 512 volts, it operates highly efficiently and is perfectly suited to supply energy-intensive consumers such as heat pumps or several electric vehicles simultaneously, even at night.Highlights at a glanceEnormous capacity: With 25.6 kWh usable capacity you achieve maximum independence from the grid and can also bridge periods of bad weather.5-stack design: The storage unit consists of five stacked 5.12 kWh modules plus control unit – compact in footprint, large in output.Maximum high-voltage efficiency: The system voltage of 512 V ensures minimal conversion losses and high discharge power with low heat generation.Industrial safety standard: Equipped with LiFePO4 cells and an integrated aerosol fire extinguishing system in each module for maximum fire protection.Sector coupling pure: Ideally dimensioned for the combination of photovoltaics, heat pump and e-mobility (wallbox).Proven communication: Compatible with powerful high-voltage hybrid inverters (e.g. Deye, Solis, GoodWe, Megarevo).Powerhouse for high demandsThis expansion level is intended for users who do not want to compromise. 25.6 kWh means that you can use the solar power produced during the day almost completely yourself, even if your night-time consumption is very high. For small businesses (bakeries, offices with server rooms), this storage unit also offers an effective option for peak shaving and serves as a powerful emergency power source in the event of a grid failure.Installation and handlingDespite an overall weight of over 260 kg, installation remains feasible thanks to the modular concept. The individual modules (each approx. 50 kg) are stacked one after the other at the installation site to form a tower. The wireless plug connection between the modules eliminates complex cabling, reducing susceptibility to errors. Characteristics ModelFelicity Solar FLH96050SG01  (25.6 kWh) System seriesFLH series (High Voltage Stackable) Configuration5x battery modules (5.12 kWh / 102.4 V each) + 1x control unit Nominal energy25.6 kWh Nominal voltage512 V Capacity50 Ah Voltage range420 V - 570 V Charging current / discharging current25 A (recommended) / 50 A (maximum) SafetyIntegrated aerosol fire extinguishing system Protection classIP65 (protected against dust and water jets) Weight (kg)approx. 300 (total system)  FAQs for the Felicity FLH96050SG01 (25.6 kWh)Which inverter is suitable for this voltage?With a nominal voltage of 512 V and a final charging voltage of up to 576 V, you need an inverter that supports this high range. The Deye SUN-10K/12K-SG01HP3 (battery input up to 700 V) is ideal for this. Some smaller HV inverters stop at 500 V or 600 V – here, you need to check the data sheet carefully to avoid overvoltage errors.How high is the storage tower?The tower, consisting of 5 modules plus BMS head and base, reaches a height of approx. 1.50 m to 1.60 m. Make sure you have a stable, level surface as the weight is distributed over a relatively small footprint (approx. 60x40 cm).Can I expand this configuration further?Technically, with the FLH96050SG01 series you can usually go up to 6 modules (approx. 30 kWh) per tower, as the voltage otherwise becomes too high for most inverters. If you need even more storage, you can alternatively place a complete second tower in parallel next to it (master/slave operation), provided the inverter supports this.Is the system suitable for commercial use?Absolutely. Due to the high capacity, cycle stability and safety features (extinguishing system), this storage unit is often used in commercial projects to increase self-sufficiency or safeguard sensitive loads. Scope of delivery: Felicity Solar FLH96050SG01 (25.6 kWh HV battery storage set) 1 x Felicity FLH96050SCG01 BMS control unitThe central high-voltage management module, which monitors the cells and communicates with the inverter.5 x Felicity FLH48100-S battery modules (each 5.12 kWh)Five stackable high-voltage LiFePO4 storage modules which, when connected in series, result in the total capacity of 25.6 kWh.1 x base plate (Base)A stable foundation for floor mounting, on which the five battery modules and the control unit are safely stacked.1 x set of internal connection cables (Plug & Play)Short plug-in connections for electrical coupling and data transmission between the five battery modules within the tower.1 x external high-voltage cable set (DC)A pair of specialised high-power cables for the safe connection of the battery tower to the high-voltage hybrid inverter.1 x communication cable (BMS-to-Inverter)A pre-configured data cable for connecting the control unit to the inverter (CAN/RS485).1 x mounting kit (tilt protection & screws)All mounting materials for fixing the tower to the wall and screws for the mechanical module connections.1 x User manualA technical manual with instructions for stacking, configuring the BMS and important safety information for high-voltage systems.

The PETZL ARIA 2 RGB is an extremely robust, compact and versatile headlamp, specially developed for activities where inconspicuousness and robustness are crucial, such as hunting, fishing or tactical operations. It combines a powerful white light output of 450 lumens with tactical RGB lighting (red, green, blue). Thanks to its exceptional impact resistance (IK07) and complete waterproofing (IP67), it is the ideal tool for the most demanding outdoor conditions. It is supplied with three AAA batteries and is also compatible with the PETZL CORE battery thanks to the HYBRID CONCEPT.Highlights at a glanceExtremely robust: Impact resistant to IK07 and drop resistant (up to 2 metres), ideal for tough outdoor use.Completely water and dustproof: Certified to IP67 (waterproof up to 1 metre depth for 30 minutes).RGB lighting: Provides red, green and blue light (constant or flashing) for night vision, inconspicuous movement or tracking.HYBRID CONCEPT: Maximum flexibility through operation with three AAA batteries (included) or optional CORE battery.Simple operation: A single switch for all functions, easy to operate even with gloves.Built for the toughest outdoor environmentsThe ARIA 2 RGB has been uncompromisingly developed for professional use in the outdoors. It is IK07 shock resistant and survives drops from up to two metres. Its IP67 certification guarantees full protection against the ingress of dust and water. The sand-coloured (desert) design provides optimum camouflage in desert, rocky or dry areas. This makes it the first choice for hunters, wildlife photographers or military users who need to trust their equipment in all conditions.Tactical and versatile RGB lightIn addition to the powerful white light (450 lumens) with mixed light beam, the ARIA 2 RGB offers a fully functional colour LED. Red light maintains the eye's dark adaptation and provides maximum inconspicuousness. Green light offers high contrast when tracking or observing nature at night and is less perceived by animals. Blue light can be used to make liquids visible (e.g. sweat traces).Flexibility and intuitive operationThanks to the PETZL HYBRID CONCEPT, you have the choice: operate the lamp with the supplied AAA batteries or upgrade to the PETZL CORE battery available separately. The lamp automatically detects the power source and adjusts the output accordingly. A single switch controls all functions, a LOCK function prevents unintentional switching on during transport and a battery level indicator gives you timely warning before the next replacement. Features  ModelPETZL ARIA 2 RGB Headlamp (Desert) ApplicationCraft, maintenance, hunting, fishing Luminosity (lumens)450 (Max Power) Lighting distance (max, m)approx. 100 Lighting modes3 white light levels, RGB light (red, green, blue) Power supplyHYBRID CONCEPT (3x AAA batteries or CORE battery) WaterproofnessIP67 (waterproof up to 1m) Shock resistanceIK07 Weight (g)approx. 106  FAQs about the PETZL ARIA 2 RGB headlampWhat is the difference between the ARIA 2 RGB and the ACTIK series?The main difference is the robustness. The ARIA 2 RGB, with IP67 (dust- and waterproof) and IK07 (shock resistant), is significantly more resistant than the ACTIK series (IPX4, splashproof). In addition, the ARIA 2 RGB offers not only red but also green and blue light, making it ideal for hunting and tactical applications.What are green and blue light needed for?Green light is often used by hunters or anglers as it scares game less and highlights contrasts in nature. Blue light is used in certain situations for tracking (e.g. making sweat visible) or in forensics.Is the CORE battery included?No, this model comes with three AAA batteries to ensure immediate readiness for use. The PETZL CORE battery is available as a separate accessory and enables rechargeable operation of the lamp.What does the IP67 protection rating mean?IP67 means that the headlamp is completely dustproof (number 6) and protected against temporary immersion in water (up to 1 metre deep for up to 30 minutes) (number 7).

The PETZL ACTIK is a powerful, compact and versatile headlamp designed for a wide variety of dynamic outdoor activities and professional applications. With a light output of 450 lumens, it provides excellent illumination for trade, industry or leisure. A particular advantage is the PETZL HYBRID CONCEPT, which enables maximum flexibility for power supply. It is supplied with three standard AAA batteries but is also compatible with the PETZL CORE rechargeable battery, which is available separately.Highlights at a glanceHigh light output: 450 lumens for powerful and wide-ranging illumination.HYBRID CONCEPT: Maximum flexibility through operation with three AAA batteries (included) or the optional CORE rechargeable battery.Versatile light modes: Mixed light beam (wide and focused) for near and distance vision as well as red continuous light to retain dark adaptation.Weatherproof and robust: Waterproof according to IPX4 standard, ideal for use in rain and demanding conditions.Easy operation: A single switch for the quick and easy selection of all light modes.Safe and comfortable: Removable, washable and reflective headband for good visibility.Powerful and versatileThe PETZL ACTIK is the ideal companion for professional users and demanding private individuals. It offers optimum illumination for tradespeople who need both hands free, for inspections in dark environments or for use in the service sector. At the same time, it is perfectly suited for dynamic outdoor activities such as running, mountaineering or camping. The red continuous light is especially useful for preserving the eye's night vision or to avoid dazzling people in groups.The Flexible HYBRID CONCEPTAt the heart of the ACTIK is PETZL's innovative HYBRID CONCEPT. This headlamp gives you a free choice of power source. It is supplied as standard with three AAA batteries (micro), ensuring worldwide availability. For regular or intensive use, however, you can easily upgrade the lamp with the PETZL CORE lithium-ion rechargeable battery, available separately. This is charged directly in the lamp via a USB port and provides an economical and sustainable energy solution.Intuitive operation and safetyOperation of the ACTIK is via a single, ergonomic switch, which is also easy to operate when wearing gloves. A LOCK function (lock function) prevents unintentional switching on of the lamp when transporting it in a backpack or toolbox. The reflective headband ensures that you are easily seen by other road users or colleagues in the dark. Features  ModelPETZL ACTIK Headlamp (Grey) ApplicationOutdoor, Running, Hiking Light output (Lumens)450 (Max Power) Lighting range (Max, m)approx. 100 Lighting modes3 white light levels, red light (continuous/blinking) Power supplyHYBRID CONCEPT (3x AAA batteries or CORE rechargeable battery) Water resistanceIPX4 (weatherproof) Weight (g)approx. 98 (incl. batteries)  FAQs about the PETZL ACTIK headlampWhat exactly does the HYBRID CONCEPT mean?The HYBRID CONCEPT means that the lamp can be operated with two different power sources. You can use either the three standard AAA batteries supplied or the rechargeable PETZL CORE battery (available separately) without the need for an adapter.Is the CORE rechargeable battery included?No, this standard "ACTIK" model comes with three AAA batteries included. The PETZL CORE rechargeable battery is available as a separate accessory and enables rechargeable operation of the lamp.What is the red light used for?The red light serves to preserve the eye's dark adaptation. It dazzles others in a group less and is ideal for use in camps, huts or for nocturnal work where night vision needs to be preserved.What does IPX4 protection mean?IPX4 means that the headlamp is protected against splashing water from all directions. It can be used in rain or damp environments without any problems, but is not suitable for immersion in water (diving).

The Deye SUN-6K-SG05LP1-EU is a state-of-the-art and powerful single-phase hybrid inverter that functions as an intelligent hub for larger photovoltaic systems. It has been developed to offer you maximum independence, efficiency, and security of supply. With a high output power of 6 kW, it manages the energy flows between your solar panels, the battery storage and the public power grid. Thanks to its integrated emergency power function, you are reliably supplied with high performance even in the event of a power failure.Highlights at a glanceIntelligent hybrid system: Manages PV generation, battery storage and mains consumption for maximum self-consumption.High performance: With 6 kW output, ideal for larger households, heat pumps or small businesses.Integrated emergency power supply: Provides uninterrupted power supply (UPS level) during mains failure.Two MPP trackers: Enables connection of two independent module fields, ideal for east-west roofs or partial shading.Flexible battery connection: Compatible with a wide range of 48V low-voltage batteries.Comprehensive monitoring: Integrated Wi-Fi module for simple and intuitive system monitoring via app.Smart energy management for your homeThe Deye hybrid inverter is more than just a converter from DC to AC. It is the brain of your energy supply. During the day, it supplies your loads directly with solar power, while surplus energy is stored in your battery for use at night or on cloudy days. Only when the storage is full and no load needs electricity is the energy fed into the public grid. This way, you maximise your self-consumption and significantly reduce your electricity costs.Maximum yields through flexible PV connectionThanks to the two integrated MPP trackers (Maximum Power Point), the Deye SUN-6K offers maximum flexibility in planning your PV system. You can connect two separate module strings with different orientations (e.g. east and west sides of the roof) or with different module types. Each tracker optimises the output of its string individually, so you always achieve the maximum possible energy yield, even in complex roof situations or partial shading.Independence through integrated emergency power supplyA special feature of this inverter is the integrated emergency power function. In the event of a failure of the public power grid, the device switches to a separate emergency power output in less than 10 milliseconds and continues to supply selected critical loads such as lighting, refrigerator or IT infrastructure with power from the battery storage. This UPS-level (Uninterruptible Power Supply) switching time ensures maximum supply reliability. Features  ModelDeye SUN-6K-SG05LP1-EU Battery input data Battery typeLead-acid or Li-ion Battery voltage range (V)40~60 Max. charging current (A)140 Max. discharging current (A)140 Number of battery inputs1 Charging strategy for Li-ion batterySelf-adaptation to BMS PV string input data Max. DC input power (W)9600 Nominal PV input voltage (V)370 Starting voltage (V)80 MPP voltage range (V)125-425 Max. DC input voltage (V)550 PV input current (A)13+22 Max. PV short-circuit current (A)17+28.6 Number of MPPT2 Strings per MPPT1+2 AC output data AC nominal power and UPS power (W)6000 Max. AC output power (W)6600 AC output nominal current (A)27.3 Maximum AC output nominal current (A)30 Max. continuous AC throughput (A)40 Peak power (without grid)2 times nominal power, 10 S Output power factor0.8 leading to 0.8 lagging Output frequency and voltage50/60Hz; L/N/PE 220/230Vac Grid typeSingle-phase Total harmonic distortion (THD)< 3% ( nominal power ) Direct current feed<0,5% ln Efficiency Max. efficiency97,60% Euro efficiency97,00% MPPT efficiency>99% Protection FusesIntegrated lightning protection, anti-islanding, reverse polarity protection, short circuit protection, overload protection, and much more. Surge categoryDC Type II/AC Type II Certifications and standards Grid approvalsVDE4105, IEC61727/62116, VDE0126, EN50549-1, CEI 0-21, AS4777, NRS2017, G98, G99, etc. Safety EMC / StandardIEC/EN 61000-6-1/2/3/4, IEC/EN 62109-1, IEC/EN 62109-2 General data Operating temperature range ( ℃ )-45~60°C, >45° C power derating CoolingIntelligent cooling Noise (dB)<30 dB Communication with BMSRS485; CAN Weight (kg)15 Size (mm)330B×580H×232T Degree of protectionIP65 Installation styleWall mount Warranty10 years  FAQs about the Deye SUN-6K-SG05LP1-EU hybrid inverterWhat exactly does "hybrid inverter" mean?A hybrid inverter can manage energy from several sources at the same time. It acts as the interface between the solar panels, the battery storage and the public power grid. It intelligently decides whether the solar power generated is used directly, stored in the battery or fed into the grid.Who is a 6 kW inverter suitable for?A 6 kW inverter is ideal for larger detached houses with higher electricity consumption, for example due to use of a heat pump or an electric vehicle. It is also suitable for small businesses or agricultural operations that want to optimise their own consumption.Which batteries are compatible with this inverter?The Deye SUN-6K is designed for use with 48V low-voltage (LV) lithium-ion battery storage systems. It is compatible with many leading manufacturers. The full compatibility list can be found on the manufacturer's website.Do I need any additional devices for the emergency power function?The inverter has an integrated emergency power output (EPS port). For use, the emergency loads to be supplied must be placed on a separate circuit by a qualified electrician and connected to this output. An additional external transfer switch is generally not required. Scope of delivery: Deye SUN-6K-SG05LP1-EU (6 kW Single-Phase Hybrid Inverter) 1 x Deye SUN-6K-SG05LP1-EU inverterA high-performance single-phase hybrid inverter with 6 kW output, integrated LCD colour touchscreen and support for 48V low-voltage battery systems.1 x Wall Mount BracketA robust metal mounting rail for secure installation of the device on a load-bearing wall.1 x Wi-Fi Stick (Data Logger)A plug-in communication module for connecting to the Internet for remote monitoring via Deye Cloud or Solarman App.1 x Current Transformer (CT)An external split current transformer for measuring energy flows at the property connection, necessary for zero feed-in and self-consumption optimisation.1 x set of PV connectors (MC4-compatible)The necessary pairs of DC connectors (plus and minus) for connecting the PV strings to the inverter.1 x Communication Cable (BMS)A pre-assembled RJ45 data cable for connection between the inverter and the battery management system.1 x Installation Kit (Screws and Plugs)A set of stainless steel screws and heavy-duty wall plugs for professional installation of the wall bracket.1 x User ManualA printed manual with detailed installation instructions, wiring diagrams and important safety information.