Test/charging devices

This "Plug & Play Giant" Smart Adapter is the indispensable tool for the professional diagnosis of Giant e-bike batteries (EnergyPak series). As Giant batteries have advanced communication and switch off their power contacts when removed, this adapter is necessary to activate the battery for testing purposes. It establishes the connection between your universal battery tester and the Giant battery and thus enables precise measurements of capacity and state of health (SoH).Highlights at a glanceSpecific compatibility: Customised for Giant EnergyPak battery systems (36V), which are installed in a large number of Giant e-bikes (e.g. Trance, Reign, Explore).BMS activation: Simulates the communication of the bike ("handshake") to wake up the battery management system (BMS) from sleep mode and release the current flow.Precise connection: Equipped with the specific Giant system connector (often 5-pin), which guarantees a secure, mechanically correct and polarity reversal-free connection.Plug & Play: Simple handling – connect the adapter, the system recognises the battery automatically, without manual configuration.Professional diagnostics: Enables dealers and service partners to create objective test reports on the actual remaining capacity.Robust design: High-quality cables and connectors, specially designed for tough everyday use in the e-bike workshop.Precise analysis for Giant EnergyPakGiant EnergyPak batteries (often manufactured in cooperation with Panasonic or Simplo) are among the most advanced on the market. For safety reasons, they do not provide any voltage when not recognised in the bicycle. This smart adapter intelligently bridges this safety function by sending the necessary signals. This allows you to discharge and test the battery outside the bike under realistic conditions in order to safely identify defective cells or age-related weaknesses.Standard for Giant service partnersIn view of the widespread use of Giant e-bikes, this adapter is a must for every professional workshop. It enables fast diagnosis of customer complaints, the assessment of trade-ins or the routine battery check during servicing. Features ModelBatterytester Smart Adapter - Giant EnergyPak 36V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Giant SyncDrive systems (EnergyPak Smart & Side Release) Frequent bike brandsGiant, Liv Nominal voltage36 V FunctionWaking up the BMS via communication pins to enable the output Connection (device)Specific connection for universal battery tester Connection (battery)Original Giant 5-pin connector (EnergyPak Smart) Special featuresSpecially developed for newer Giant models with 5-pin charging socket Weight (g)approx. 195  FAQs about the Smart Adapter for GiantDoes the adapter work for all Giant batteries?The adapter covers the majority of modern Giant EnergyPak batteries (36V), as used in the hybrid models. For very old models (before 2013/2014) or special 26V systems, please check the plug shape. This adapter is optimised for the common 3-pin and 5-pin EnergyPak systems (side-release/top-release).Can I measure the voltage without an adapter?No. Giant batteries are in "deep sleep" or protection mode when they are removed. The main contacts are de-energised. Without the adapter that sends the wake-up signal, a multimeter shows 0V.Can I charge the battery via the adapter?This adapter is primarily designed for discharging and diagnostics. Charging should always be done with the original Giant Smart Charger, as this communicates with the BMS via additional lines (often 6-pin on the charger) to control the balancing of the cells.Do I need software for this?The adapter is the hardware interface. To perform the test and evaluate the data (capacity curve, protocol), you need the corresponding basic tester and its PC software.

This specialised "Plug & Play" Smart Adapter is the professional interface for the diagnosis of e-bike batteries of the "Silent" drive system. This system is mainly used for special bikes from Van Raam (e.g. tricycles, therapy bikes) and high-quality touring bikes from Utopia Velo. As these batteries (often "Cube" batteries) have intelligent communication, they require an activation signal to release the current flow for testing purposes. The adapter establishes this connection and enables precise capacity measurement.Highlights at a glanceSpecific compatibility: Customised for the "Silent Elektro" drive system (36V), which is installed in bicycles from Van Raam (e.g. Easy Rider, Fun2Go) and Utopia Velo.BMS activation: Simulates the communication of the e-bike to wake up the battery management system (BMS) from sleep mode and close the main contacts.Plug & Play: Simple and safe connection directly to the battery – the adapter automatically takes over the necessary signal transmission.Professional diagnosis: Indispensable for medical supply stores, rehabilitation technicians and specialised bicycle dealers to ensure the reliability of batteries in therapy bikes.Robust quality: High-quality cables and durable connectors, designed for regular use in service workshops.Safe operation: Prevents incorrect measurements and protects the sensitive electronics of the battery through correct pin assignment and signalling.Precise analysis for the Silent systemBatteries of the Silent Elektro system (often recognisable by their cube shape or position in the luggage carrier on tricycles) are safety-optimised. When removed, the contacts are de-energised. This smart adapter intelligently bridges this safety function. It allows your battery tester to simulate a realistic load in order to determine whether the battery still offers the necessary range for the often critical use in the rehabilitation and mobility sector.Standard for specialised bike serviceReliability is the top priority, especially for therapy bikes and e-bikes for people with disabilities. With this adapter, Van Raam and Utopia Velo dealers can ensure that used or older batteries still meet the requirements and provide customers with well-founded service reports. Features ModelBatterytester Smart Adapter - Van Raam / Utopia / Silent ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Silent electric drive systems Frequent bike brandsVan Raam (therapy bikes, tricycles), Utopia Velo, Silent Supported battery typesSilent Elektro Li-Ion batteries (often "cube" shape or carrier) Nominal voltage36 V (partly also compatible with 24 V systems, depending on adapter version) FunctionActivation of the BMS (smart function) to release the discharge current Connection (device)Specific connection for universal battery tester Connection (battery)Specific Silent Elektro system plug (usually 4-pin or Rosenberger) Weight (g)approx. 190  FAQs about the adapter for Van Raam / UtopiaDoes the adapter work for all Van Raam bikes?The adapter is designed for the electric Silent System (Silent Elektro), which is used on most modern Van Raam e-bikes (Li-Ion, 36V). Older models with other motors or lead batteries may not require this special adapter or may use other connections.Can I use it to test Utopia Velo batteries?Yes, provided the Utopia bike is equipped with the Silent electric drive (which is the case with many Utopia E-bike models). Check in advance whether the charging plug matches the adapter.Can I measure the voltage without an adapter?No. The batteries of the Silent system switch to "sleep mode" when they are not in the bike or are not being charged. A multimeter shows 0V at the contacts. The adapter is absolutely necessary to activate the voltage.Is the adapter also suitable for charging?This adapter is primarily intended as a diagnostic tool for the discharging process on the test device. For safety reasons and to ensure correct cell balancing, the batteries should always be charged using the manufacturer's original charger.

This specialised Smart Adapter is the indispensable tool for the professional diagnosis of Shimano Steps E-Bike batteries of the E6000 series (36V). As Shimano batteries have a highly developed battery management system and, for safety reasons, do not have any voltage at the contacts when removed, this adapter is absolutely essential. It not only establishes the physical connection, but also sends the necessary "wake-up signal" so that the battery releases the discharge output for precise capacity measurement.Highlights at a glanceSpecific compatibility: Developed for the Shimano Steps E6000 system (City/Trekking), suitable for common frame and rack batteries of this series (e.g. BT-E6000, BT-E6010).BMS activation: Simulates the communication of the drive unit ("handshake"), to wake the battery from sleep mode and close the main contacts.Precise connection: Features the specific Shimano system plug, which creates a mechanically secure and reverse-polarity safe connection to the battery terminals.Professional diagnosis: Enables dealers to generate objective test reports on remaining capacity and state of health (SoH), essential for service and resale.Robust workshop quality: High-quality cables and durable contacts guarantee reliability in daily, intensive use in the bike workshop.Plug & Play: Easiest handling without complex settings – connect the adapter, the test system automatically detects the battery.Precise analysis for Shimano Steps E6000The Shimano Steps E6000 system is one of the most widespread drive systems in the trekking and city sector. However, the associated batteries are immediately switched off when disconnected from the bike. Simple voltage measurement is therefore not possible. This smart adapter intelligently bridges this safety function by simulating the presence of the bike. In this way, your battery tester can apply a realistic load and check whether the battery still delivers full power or whether cells have aged.Standard for trekking and city bikesAs the E6000 system has been installed in countless models over the years, these batteries now often come in for servicing. Whether for troubleshooting range issues or assessing trade-ins – this adapter puts an end to the guesswork and delivers hard facts. Features ModelBatterytester Smart Adapter - Shimano Steps E6000 / E8000 ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Shimano Steps E6000, E6100, E7000, E8000 series Compatible battery typesBT-E6000, BT-E6001, BT-E6010, BT-E8010, BT-E8020 (frame, rack & Intube) Nominal voltage36 V FunctionActivation of the BMS (wake-up) to enable the discharge output Connection (device)Specific connection for universal battery tester Connection (battery)Shimano Steps specific adapter plug Special featuresAllows the battery to be tested when removed without bike Weight (g)approx. 210  FAQs about the Smart Adapter for Shimano StepsDoes the adapter also fit Shimano E8000 or EP8?This depends on the design of the battery. The E6000 series partly uses different connectors than the more compact MTB systems (E8000/EP8). This adapter is optimised specifically for the connections of the E6000 generation (often BT-E6000/6001/6010). For newer systems, please check the plug compatibility.Can I measure voltage without the adapter?No. Shimano batteries are in "deep sleep" when not communicating. The contacts are de-energised (0V). Only with the Smart Adapter, which activates the system, is measurement possible.Can I charge via the adapter?The adapter is designed for the discharge process (test/diagnosis). For charging you should always use the original Shimano charger (e.g. EC-E6000), as this communicates directly with the BMS to control cell balancing.Which battery models exactly is it for?It generally fits the widely used BT-E6000 (rack) and BT-E6010 (frame/downtube) batteries and their variants used in the E6000 system.

This specialised Smart Adapter is the professional connection solution for the diagnosis of e-bike batteries of the classic Stromer ST1 (36V). The legendary Stromer S-Pedelecs (models up to approx. year of manufacture 2017) use powerful 36V batteries (often known by their colours such as purple, gold, etc.) with a magnetic Rosenberger connector (EnergyBus standard). This adapter establishes the secure connection between your battery tester and the battery, manages the necessary signal transmission and thus enables precise measurement of the residual capacity and state of health (SoH).Highlights at a glanceSpecific compatibility: Customised for the 36V batteries of the classic Stromer ST1 series (not suitable for the new 48V models from 2019).EnergyBus / Rosenberger: Equipped with the special magnetic connector, which guarantees self-aligning, wear-free and reverse polarity protected contacting.BMS activation: Simulates the communication of the Stromer system to prompt the battery management (BMS) to release the discharge current.Professional diagnosis: Indispensable for Stromer dealers to reliably assess the condition of used batteries in these high-priced S-Pedelecs.Plug & Play: Easy handling – the magnetic connector connects almost by itself, the tester recognises the battery automatically.Robust workshop quality: High-quality cables and strain reliefs ensure durability in daily service operation.Precise analysis for Stromer premium batteriesStromer batteries are among the most powerful on the market. As they are often used in S-Pedelecs (up to 45 km/h), they are exposed to high loads. A simple voltage test is not sufficient here. This Smart Adapter enables your test device to simulate a realistic riding load. In this way, you can determine whether the battery still delivers full power for high speeds or whether the internal resistance has become too high due to ageing.Standard for the S-Pedelec serviceAs Stromer ST1 models are very durable and sought-after on the used market, battery diagnostics are a key factor in retaining value. With this adapter, workshops can produce well-founded service reports and advise customers professionally. Features ModelBatterytester Smart Adapter - Stromer ST1 36V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Stromer ST1 (Classic models, up to approx. year of manufacture 2017) Battery typesStromer 36V batteries (Purple, Gold, etc.) Nominal voltage36 V FunctionActivation of the BMS (Wake-Up) via the bus pin (EnergyBus protocol) Connection (device)Specific connection for universal battery tester Connection (battery)Rosenberger RoPD connector (magnetic) Special featuresSpecially for the 36V generation (not compatible with 48V ST2/ST3/ST5) Weight (g)approx. 190  FAQs about the Smart Adapter for Stromer ST1Does the adapter also fit the new Stromer ST1 (from 2019) or ST2/ST3?No. The classic Stromer ST1 models (V1) ran on 36V. All newer models (new ST1, ST2, ST3, ST5) are based on a 48V system with a different design and connector assignment. This adapter is exclusively for the 36V generation.Does the adapter also work for other batteries with Rosenberger plugs?The Rosenberger connector (EnergyBus) is also used by other brands (e.g. GoSwissDrive, Brose/BMZ). As the pin assignment for data communication may vary, this adapter is specifically optimised for the Stromer ST1 protocol. The appropriate adapters should be used for other systems.Can I measure the battery without an adapter?No. The magnetic connection is de-energised in idle state to prevent short circuits from adhering metal parts. Without the adapter, which sends the release signal, no voltage can be measured at the contacts.Can I charge via the adapter?The adapter is designed for the discharge process (diagnosis) on the test device. Charging should always be carried out with the original Stromer charger, as temperature and balancing are also monitored.

This specialised Smart Adapter is the professional connection solution for the diagnosis of Trek e-bike batteries equipped with the BionX drive system (Ride+). BionX systems, especially in the Trek-specific integration, are known for their complex CAN bus communication. As these batteries do not carry any voltage at the contacts when removed, this adapter is necessary to activate the battery management system (BMS) and enable the battery for precise capacity measurement.Highlights at a glanceSpecific compatibility: Customised for Trek e-bikes with BionX drive (Ride+ series) that have the specific Trek charging connection (36V / 37V system).BMS activation: Takes over the necessary CAN bus communication to wake the battery from "deep sleep" and close the main contacts for the test.Plug & Play: Simple connection directly to the charging socket of the battery – the adapter is recognised by the test system and starts activation automatically.Professional diagnostics: Enables dealers to create objective test reports (SoH/residual capacity), essential for evaluating the many Trek Ride+ bikes still in circulation.Safe connection: The specific connector prevents polarity reversal and ensures a firm contact for the high currents during the discharge test.Robust workshop quality: High-quality cables and durable components guarantee reliability in daily service use.Precise analysis for Trek Ride+ (BionX)The BionX system in Trek bikes (often referred to as Ride+) has been a market leader in the rear motor segment for years. The batteries are "intelligent" and switch off for safety reasons if they are not connected to the console or the motor. This smart adapter simulates the periphery of the e-bike. As a result, the BMS opens the circuit, and your battery tester can simulate a realistic load to determine whether the battery is still powerful or whether cells have become highly resistive due to ageing.Indispensable for servicing Trek classicsTrek e-bikes are very durable and of high quality. Many customers want to continue using their older Ride+ models. For workshops, this adapter is the key to offering these customers a professional battery service, whether for fault diagnosis in the event of a loss of range or for pre-sale checks. Features ModelBatterytester Smart Adapter - BionX / TREK (Ride+) ApplicationConnection cable for capacity test / diagnostics Compatibility (System)Trek Ride+ systems (based on BionX technology) Frequent bike brandsTrek, Diamant, Villiger (models with Ride+ drive) Rated voltage37 V / 40.7 V (often referred to as 36V) FunctionActivation of the BMS (Wake-Up) by simulating the G2/G3 console Connection (Device)Specific connection for universal battery tester Connection (Battery)Specific Trek Ride+ system connector (usually Hirose or Sub-D depending on version) Special featuresEnables discharging of "Smart Batteries" that lock without communication Weight (g)approx. 185  FAQs about the Smart Adapter for BionX TREKDoes the adapter fit all BionX batteries?No. BionX has produced different housing shapes and connectors. This adapter is specific to the Trek integration (Trek Ride+), which often uses its own plug shape on the charging socket. There are other adapters for standard BionX batteries (rail battery or universal rack).Can I measure the voltage without an adapter?No. BionX batteries are completely de-energised when not in use. A multimeter shows 0V at the contacts. Without the Smart Adapter, which sends the digital "wake-up signal" via the CAN bus, no measurement or diagnosis is possible.Can I charge via the adapter?The adapter is primarily designed for connection to the diagnostic device (discharging). Due to the integrated balancer technology, BionX batteries should always be charged with the original Trek/BionX power supply unit.Is the adapter suitable for the 48V BionX systems?This adapter is explicitly designed for the 36V / 37V Generation shown. The newer 48V BionX systems (D-series etc.) often use the same connector, but may have a different communication protocol or pin assignment. Please check the compatibility of your test device for 48V. 

This high-quality E-Bike Vision quick charger is the ideal solution for quickly and safely charging all 26V E-Bike Vision PowerPack (POP) batteries developed for the Panasonic 26V system. With a high charging current of 5 amps (5A), it charges your battery noticeably faster than many standard chargers, thus minimising the waiting time until your next tour. The robust and compact design makes it the perfect charger for home, the office or holidays.Highlights at a glanceFast charging: With 5 amps of charging current, your 26V e-bike battery is charged quickly and efficiently.Specific compatibility: Exclusively for all 26V E-Bike Vision PowerPack (POP) batteries for the Panasonic system.Intelligent charging electronics: Permanently monitors the charging process and switches off automatically after full charge to protect the battery.High safety: Comprehensive protection against short circuit, overheating, and overvoltage.Compact and robust: Lightweight and durable housing, ideal for everyday use and on-the-go.Less waiting, more ridingReduce charging time and maximise your time on the bike. With a charging current of 5 amps, this quick charger is considerably more powerful than many included standard chargers. For example, an empty battery with 23Ah capacity is fully ready for use again in just approx. 4.5 hours. The LED display provides you with clear and precise information about the current charge status at all times.Safe and gentle for your batteryDespite the high charging speed, the safety and longevity of your valuable battery are paramount. The intelligent charging electronics optimally adapt the charging process to the condition of the battery. Once full capacity is reached, the device automatically switches to maintenance mode to prevent overcharging and maximise the lifespan of the battery cells.Specialist for the 26V systemThis charger was specifically developed for E-Bike Vision batteries of the widespread 26V Panasonic mid-motor system. It ensures perfect electronic coordination and communication with the battery management system (BMS) of these batteries to guarantee an optimal and safe charging process. Features  ModelE-Bike Vision Quick Charger 26V 5A ApplicationCharger for 26V E-Bike batteries Input voltage100 - 240V AC Output voltage (V)29.4 Charging current (A)5 Connection (battery)System-specific charging adapter required DisplayLED status display Dimensions (L x W x H in mm)approx. 180 x 85 x 50 Weight (g)approx. 650  FAQs about the E-Bike Vision Quick ChargerWhat does 5A charging current mean and how does it affect the charging time?The "5A" stands for 5 amps of charging current. This is the "speed" at which the battery is charged. A 5A charger charges a battery more than twice as fast as a 2A standard charger. The exact charging time is calculated from the capacity of the battery (in Ah) divided by the charging current (in A), for example: 23 Ah / 5 A = 4.6 hours.Can I use this charger for my original 26V Panasonic battery?No, this charger is specifically designed for the E-Bike Vision replacement batteries (PowerPacks). To charge an original Panasonic battery, you will still need your original Panasonic charger.Is fast charging harmful to my battery?Modern lithium-ion batteries and their battery management systems (BMS) are designed for fast charging with currents such as 5A. The intelligent electronics in the charger and battery ensure that the charging process is safe and within the optimal range, so as not to adversely affect the life of the cells.Can I leave the battery on the charger overnight?Yes, it is safe. The intelligent charger detects when the battery is fully charged and automatically terminates the main charging process. It then switches to a maintenance mode with very low current to keep the battery full without overcharging it.

This Mascot desktop charger has been specially developed for the high demands of modern lithium iron phosphate batteries (LiFePO4). With its 3-stage charging characteristic, tailored to LiFePO4 cells, it ensures safe, fast and cell-protecting full charging. The dedicated input voltage range of 198-264V makes this device an efficient solution for operation on stable 230V networks in Europe and industrial environments.Highlights at a glanceOptimised for LiFePO4: Special charging profile precisely matched to the voltage level and safety requirements of lithium iron phosphate batteries.Intelligent 3-stage charging: Process-controlled charging (CC-CV-Cutoff/Float) ensures full capacity without the risk of overcharging, which would be critical for lithium batteries.Efficient mains operation: Designed for an input voltage range of 198-264 VAC, ideal for dedicated 230V applications.High safety standards: Comprehensive protective circuits against short circuit, reverse polarity and overheating protect both the charger and the valuable battery.Robust construction: Designed as a desktop device, it provides a rugged housing for daily use in workshops, industry or medical technology.Status LED: The integrated LED indicator provides clear feedback on the current operating state (charging / finished / error).Gentle charging technology for lithium batteriesUnlike lead-acid batteries, LiFePO4 batteries require very precise shut-off. The Mascot charger uses a 3-stage process for this:Constant current (CC): The battery is quickly charged to approx. 90% with maximum current.Constant voltage (CV): The voltage is kept constant, while the current decreases, to fully saturate and balance the cells.End of charge / maintenance: After saturation the device switches off or changes to a safe monitoring mode to avoid stressing the battery with unnecessary float charging (model dependent).Reliability for professional applicationsMascot is known for durable power supply solutions. This LiFePO4 charger is excellently suited for mobile applications, electric vehicles, cleaning equipment or medical devices that rely on advanced lithium technology and require a reliable energy source. Features ModelMascot 2840 LiFePO4 (desktop charger) ApplicationCharger for lithium iron phosphate batteries (LiFePO4) Input voltage198 - 264 V AC (47-63 Hz) Charging voltageVariable depending on version (for 1 to 16 cells) Charging currentMax. 8.5 A (depending on voltage) Charging method3-stage (current detection as charge stop) Indicators3-colour LED (Red=Charging, Orange=End phase, Green=Finished) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)135 x 80 x 44 Weight (kg)approx. 0.48  FAQs about the Mascot LiFePO4 desktop chargerCan I also use it to charge lead-acid batteries?No, this device is specially matched to the voltage characteristics of LiFePO4 cells. Charging lead-acid or other lithium chemistries (such as Li-Ion/LiPo) may result in incomplete charging or damage to the battery. Please use the relevant Mascot models for those applications.What does the input voltage range 198-264V mean?This range indicates that the charger is optimised for operation on power grids with a nominal voltage of 230V (as is common in Europe). It is not suitable for worldwide use in countries with 110V networks (e.g. USA), which often allows greater efficiency in the intended range.When is the battery fully charged?The battery is fully charged when the LED indicator turns green. The charger has then completed the constant voltage phase and has reduced or switched off the charging current to a minimum.Which plugs are compatible with the device?As with many Mascot desktop devices, the DC output is often designed flexibly (e.g. fixed cable or interchangeable plug system). Please check the specific product description for your model to ensure that the plug (e.g. XLR, hollow plug) matches your charging socket.

This compact 12V desktop charger with 4 amp charging current is the ideal all-rounder for maintaining and charging medium-sized lead-acid batteries. It bridges the gap between small maintenance chargers (often only 0.8 A) and large workshop chargers. With 4 amps it charges car, motorbike and service batteries quickly without subjecting them to thermal stress.Thanks to the intelligent, microprocessor-controlled IUoU charging curve, the device operates fully automatically: It charges the battery up to the final charging voltage and then automatically switches to maintenance mode. This means the charger can be left connected permanently (e.g. for overwintering) without overcharging the battery.Highlights at a glanceUniversally applicable: Suitable for all 12V lead-acid types: wet batteries (car), maintenance-free MF, AGM, VRLA and gel batteries.3-stage automatic: Charges with constant current (main charge), constant voltage (saturation) and switches to "floating" (maintenance charge).Optimal charging current (4A): Perfectly dimensioned for battery capacities of approx. 12 Ah to 80 Ah. Charges quickly, yet gently on the battery.Safety package: Protection against reverse polarity (incorrectly connected clamps), short circuit, overheating and sparking.LED status display: Easy control of the charging status (e.g. Red = Charging / Green = Full / Yellow = Error).Compact design: The lightweight plastic housing fits on any workbench or in any shelf ("desktop unit").Areas of applicationThe 4A charger can be used in many ways in the hobby and private sector:Car & motorbike: For recharging the starter battery or for maintaining the charge of seasonal vehicles (convertible, classic car).Lawnmowers & ride-on mowers: Ideal for the starter batteries of garden tools in winter.Leisure & hobby: For 12V batteries in bait boats, echo sounders, camping power supplies or small solar systems.Rehab & mobility: (If the appropriate plug is available) for smaller electric vehicles or stairlifts with 12V system.Installation & Safety InstructionsConnection sequence:Connect the red clamp (+) to the positive terminal of the battery.Connect the black clamp (-) to the negative terminal.Only now plug the mains plug into the socket.Ventilation: When charging open lead-acid batteries, explosive gases (oxyhydrogen) may be generated. Only charge in well-ventilated rooms and avoid open flames or sparking.Indoor use: The device is (mostly) not waterproof (IP20). Protect it from wetness and moisture.Defective batteries: The charger often only recognises deeply discharged batteries above a certain residual voltage (e.g. 2V). For safety reasons, a completely "dead" battery (0V) is often not charged. Features ModelMascot 2040 (12V version) Battery type**Lead-acid, AGM, Gel, VRLA** Nominal voltage**12 V** Charging current (max.)**4.0 A** End-of-charge voltage**14.7 V** (Cyclic) / **13.7 V** (Float) Input voltage90 V - 264 V AC (worldwide use) Recommended battery capacity**15 Ah to 100 Ah** Degree of protection**IP41** (drip water protected) ConnectionCrocodile clamps (replaceable with DC plug) Weightapprox. 350 g (compact design) FAQs about the 12V 4A lead-acid chargerCan I use it to charge my lithium battery (LiFePO4)?No, better not. Lead-acid chargers often have a desulphation function (high voltage pulses) or a float voltage that is too high, which can confuse the BMS (battery management system) of a lithium battery or damage the cells. Always use a special LiFePO4 charger for lithium batteries.Can I leave the charger on the motorbike all winter?Yes. As soon as the battery is full (green LED), the device switches to maintenance charging. It then only delivers tiny impulses of current to compensate for self-discharge. This is perfect for winter storage.How long does it take to charge a car battery (60 Ah)?With a charging current of 4 amps you can roughly calculate: Capacity / charging current + losses. 60 Ah / 4 A = 15 hours. In practice it takes a little longer (approx. 18-20 hours) as the current drops towards the end. However, for a quick "jump start charge" 1-2 hours are often enough.

The Ansmann ALCS 2-24 A is an intelligent and universal desktop or plug-in charger for lead battery systems. The special feature of this device is its fully automatic voltage detection: it automatically detects whether a 2V, 6V, 12V or 24V battery is connected and adjusts the charging parameters accordingly. This makes it the ideal all-rounder for hobby, car workshops and home use to safely charge and maintain lead-acid, lead-gel and lead-fleece (AGM) batteries over winter.Highlights at a glanceFully automatic voltage detection: The device automatically detects the voltage of the connected battery (2V, 6V, 12V or 24V) and sets the optimal charging mode – no manual switches required.Versatile compatibility: Suitable for all common lead battery types (lead-acid, lead-gel, lead-fleece/AGM) with capacities of approx. 1.3 Ah to 24 Ah.Overcharge protection & trickle charge: After reaching the final charging voltage, the device automatically switches to trickle charging, which prevents overcharging and keeps the battery fresh.Winter mode: Perfectly suited for winter storage of seasonal vehicles (motorbike, vintage car, lawn tractor), as the battery can remain connected at all times.Safety features: Equipped with protection against short circuit and reverse polarity (incorrect connection), indicated by red LEDs to prevent damage to the battery and device.Easy connection: The high-quality terminal clamps (crocodile clips) enable quick and secure contact with the battery terminals.Intelligent charging technology "Connect & Forget"The ALCS 2-24 A works according to the "connect and forget" principle. As soon as the terminal clamps are in contact, the microprocessor analyses the battery. Charging is carried out according to an IU characteristic curve, which first charges the battery with constant current and then keeps the voltage constant. The charging currents adapt to the voltage:2V batteries: 900 mA6V batteries: 700 mA12V batteries: 600 mA24V batteries: 300 mA This ensures gentle charging for small to medium-sized batteries.Ideal for hobby and householdWith its wide coverage from 2V to 24V, this one device replaces several individual chargers. It is ideal for charging batteries in children's vehicles (often 6V or 12V), motorbikes, alarm systems, UPS systems or hand-held spotlights. Features ModelAnsmann ALCS 2-24 A ApplicationAutomatic charger for lead-acid, lead-gel & lead-fleece batteries Battery voltage2V / 6V / 12V / 24V (Automatic setting) Charging current900mA (at 2V)700mA (at 6V)600mA (at 12V)300mA (at 24V) Recommended capacity1.3 Ah to 24 Ah Charging methodIU characteristic curve (Automatic switchover to trickle charge) ConnectionInsulated crocodile clips (fixed cable 3.5m) Protective functionsReverse polarity protection, short-circuit protection, overcharge protection Dimensions (L x W x H in mm)106 x 68 x 51 Weight (g)approx. 520  FAQs about the Ansmann ALCS 2-24 AHow do I know if the battery is full?The green "Charge" LED lights up during charging. When this LED goes out or its intensity changes significantly (model dependent, often switches to trickle charge), the battery is fully charged. The device can then remain connected.Can I use it to charge a car battery?Theoretically yes, but it takes a very long time. With 600mA charging current at 12V, an empty 60Ah car battery would take about 100 hours to charge. The device is intended more for motorcycle batteries or for maintenance (care in winter) of car batteries, not for rapid recharging of large starter batteries.What happens if I swap the clamps?The device has electronic reverse polarity protection. If you swap plus and minus, a red LED ("Polarity") lights up and the charging process does not start. No damage occurs to the device.Can I use it to charge lithium batteries?No, not at all. This charger is only designed for lead-acid technologies. Lithium batteries require special charging methods; connecting them to this device can destroy the lithium battery or pose a safety risk.

This versatile Ansmann plug-in charger is the ideal solution for users who want to maintain a wide variety of lead-acid batteries with just one device. It covers the entire voltage range from 2V to 24V and is specially designed for small to medium capacities from 2.4 Ah to 24 Ah. Thanks to the intelligent charging technology, the voltage is set fully automatically – incorrect operation due to incorrect voltage selection is therefore impossible. It is ideal for lead-acid, lead-gel and AGM batteries.Highlights at a glanceFully automatic voltage detection: The device analyses the connected battery and automatically sets itself to 2V, 6V, 12V or 24V.Wide range of applications: Optimised for battery capacities from 2.4 Ah to 24 Ah, ideal for motorbikes, ride-on mowers, alarm systems or classic cars.Gentle charging: Automatically adjusts the charging current to the voltage level (e.g. 900mA at 2V to 300mA at 24V) to prevent the battery from overheating.Overcharge protection & maintenance: Once fully charged, the device switches to trickle charge mode, allowing the battery to remain permanently connected (e.g. over the winter).Safety functions: Electronic protection against short circuit, reverse polarity and overcharging guarantees safe operation.Easy handling: Equipped with insulated pole clamps for quick contact; LED indicators provide information about charging operation and possible faults.Intelligent charging technology for a long service lifeThe special feature of this charger is the microprocessor control. It prevents the "gassing" of the battery that often occurs with simple chargers by precisely limiting the voltage. The charging process takes place according to an IU characteristic curve: First, charging takes place at a constant current (I phase) until the final charging voltage is reached. Then the voltage is kept constant (U phase) while the current decreases. This ensures that the battery is charged to 100% without being damaged.Ideal for seasonal vehicles and hobbyAs the device is permanently chargeable, it is perfect for winter storage. You simply connect it to the battery of your motorbike, classic car or lawn tractor in autumn and the vehicle is ready to go in spring. It is also ideal for 6V children's toy cars or 24V wheelchair batteries (smaller capacity). Features ModelAnsmann ALCS 2-24 A ApplicationAutomatic charger for 2V, 6V, 12V and 24V lead-acid batteries Suitable battery typesLead-acid, lead-gel, lead-fleece (AGM) Battery voltage2V / 6V / 12V / 24V (automatic detection) Charging current900mA (at 2V)700mA (at 6V)600mA (at 12V)300mA (at 24V) Recommended capacity2.4 Ah to 24 Ah Charging methodIU characteristic (automatic switchover to trickle charge) ConnectionHigh-quality pole terminals (crocodile clips) Protective functionsReverse polarity protection, short circuit protection, overcharge protection Weight (g)approx. 520  FAQs about the Ansmann 2-24V chargerWhat happens if I connect a deeply discharged battery?As the device has to recognise the voltage automatically (e.g. differentiating between a full 6V battery and an empty 12V battery), problems can occur with deeply discharged batteries (below a certain minimum voltage). The device may then recognise the battery as defective or select a lower voltage level. Deep-discharged batteries often require special refreshers.Can I use the charger for my car?For trickle charging (winter storage), yes. For complete charging of an empty car battery (e.g. 60 Ah), however, the charging current of 0.6 amps is too low. The charging process would take several days. More powerful Ansmann car chargers are recommended for this purpose.How long can the device remain connected?Unlimited. The device is explicitly designed for continuous operation. The trickle charge function equalises the self-discharge of the battery without overcharging it.What do the LEDs on the device mean?Power (Red): Mains plug is plugged in, device is ready. Charge (Green): Battery is being charged. Polarity (Red): Battery is connected the wrong way round (polarity reversal). Please swap the terminals. 

The Mascot 2240-24 is a versatile and compact desktop charger for 24V lead-acid battery systems. It is characterised by its intelligent 3-stage charging technology, which ensures gentle and complete charging of lead-acid, gel and AGM batteries. Thanks to the modular plug system, this device is extremely flexible: both the mains connection (AC-X) and the output connection (DC-X) are designed for interchangeable plugs, making the charger the ideal universal solution for international use and a wide range of 24V applications.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle (cycle, timer, float) for gentle charging and maximum battery life.AC-X input system: Interchangeable mains plugs enable worldwide use without having to store separate country versions.DC-X output system: Interchangeable secondary plugs (snap-lock or jack) for flexible adaptation to different charging sockets.Wide compatibility: Suitable for all 24V lead-acid batteries, including maintenance-free wet, AGM and gel types.Safe operation: Comprehensive protection against reverse polarity and short circuit as well as an LED status display.Robust design: Compact housing, certified to IP40 (optional IP41) for safe operation.Maximum flexibility thanks to interchangeable plugsThe Mascot 2240-24 is consistently designed for adaptability. Thanks to the AC-X system, the charger can be operated worldwide by simply plugging in the appropriate mains adapter (e.g. EU, UK, US, AUS). At the same time, the DC-X system on the output cable allows the charging plug to be changed quickly without having to solder. This significantly reduces the need to stock different country or device variants and offers a universal solution for service and export.Gentle battery care for a long service lifeThe proven 3-stage charging characteristic guarantees that your 24V batteries are not only charged, but also maintained. After the main charge with constant current, a timer-controlled phase ensures safe full charging before the device automatically switches to float charging. This compensates for self-discharge and keeps the battery permanently ready for use without subjecting it to thermal stress.Reliability for professional applicationsMascot chargers are known for their durability and quality. The 2240-24 model is ideal for small medical devices, safety applications, wheelchairs or mobile measuring devices that run on 24 volts. The LED display provides clear information about the current status (charging / full) at all times, and the integrated protective functions prevent damage in the event of incorrect operation. Features ModelMascot 2240 (24V / 0.5A) AC-X/DC-X ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)29.4 V / 27.6 V Charging current0.5 A Charging method3-stage (Boost, Timer, Float) Special featureInterchangeable mains plugs (AC-X) & output plugs (DC-X) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)90 x 45 x 32 Weight (g)approx. 115  FAQs about the Mascot 2240-24 chargerWhat is the difference between the 2040 and the 2240 series?The 2240 model is the more compact version with lower output (here 0.5 A charging current), ideal for smaller batteries. The 2040 series offers higher charging currents and is designed for larger capacities. However, both utilise the high-quality 3-stage charging technology.What do AC-X and DC-X mean?AC-X and DC-X are the terms for Mascot's flexible connector system. AC-X means that the mains plug (for the socket) is interchangeable (clip system). DC-X means that the plug towards the battery can also be changed to adapt it to different device sockets.Are the interchangeable plugs included in the scope of delivery?This depends on the specific item configuration. The charger is often supplied as a basic unit and the required AC and DC plugs must be ordered separately depending on the application. Please check the exact contents of the set.What battery sizes is the device suitable for?The 2240-24 is a compact charger for smaller battery capacities. It is ideal for 24V battery packs in the range of approx. 2 Ah to 12 Ah (e.g. in small medical devices or backup systems).

The Mascot 2240-12 is a versatile and compact charger for 12V lead-acid batteries that impresses with its enormous flexibility. Equipped with intelligent 3-stage charging technology, it ensures gentle and safe charging of lead-acid, gel and AGM batteries. The special feature of this model is the modular plug system: both the mains connection (AC-X) and the output connection (DC-X) are designed for interchangeable plugs, making the device the ideal solution for worldwide use and for a wide variety of end devices.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle (cycle, timer, float) for maximum battery life.AC-X input system: Interchangeable mains plugs enable worldwide use (plug optional/configurable).DC-X output system: Interchangeable secondary plugs for flexible adaptation to different charging sockets.Wide compatibility: Suitable for all 12V lead-acid batteries (wet, AGM, gel).Safe operation: Protection against reverse polarity and short circuit as well as LED status display.Robust design: Compact housing, certified to IP40/IP41 for safe operation.Maximum flexibility thanks to interchangeable plugsThe Mascot 2240 is designed for adaptability. Thanks to the AC-X system, the charger can be operated worldwide by simply plugging in the appropriate mains adapter (e.g. EU, UK, US, AUS). At the same time, the DC-X system allows the charging plug (e.g. hollow plug, jack, XLR) on the output cable to be changed quickly without having to solder. This reduces stock-keeping and offers a universal solution for service and export.Gentle battery careThe proven 3-stage charging characteristic guarantees that your batteries are not only charged, but also maintained. After the main charge, a timer-controlled phase ensures a full charge before the device automatically switches to float charging. This compensates for self-discharge and keeps the battery permanently ready for use without subjecting it to thermal stress.Reliability for professional applicationsMascot chargers are known for their durability. The 2240 model is ideal for small medical devices, safety applications or mobile measuring devices. The LED display provides clear information about the current status (charging / full) at all times, and the protective functions prevent damage in the event of incorrect operation. Characteristics ModelMascot 2240 (12V / 1.3A) AC-X/DC-X ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)14.7 V / 13.7 V Charging current1.3 A Charging method3 stages (boost, timer, float) Special featureInterchangeable mains plug (AC-X) & output plug (DC-X) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)90 x 45 x 32 Weight (g)approx. 115  FAQs about the Mascot 2240 chargerWhat do AC-X and DC-X mean?AC-X and DC-X are the names for the flexible plug system from Mascot. AC-X means that the mains plug (for the socket) is interchangeable (clip system). DC-X means that the plug can also be changed towards the battery to adapt it to different device sockets.Are the interchangeable plugs included in the scope of delivery?This depends on the specific item configuration. Often the charger is supplied as a basic unit and the required AC and DC plugs must be ordered separately to suit the application. Please check the exact scope of delivery.What battery sizes is the device suitable for?The 2240-12 is a compact charger for small to medium battery capacities. It is ideal for 12V batteries in the range of approx. 3 Ah to 12 Ah (e.g. in hand lamps, small UPS systems or medical devices).Can I leave the charger permanently connected?Yes. As soon as the battery is full, the device switches to maintenance charging. The battery can remain on the charger for an extended period to maintain full capacity (e.g. during winter storage).

The Mascot 2040 is a high-quality 3-stage charger for 12V lead-acid batteries that has been specially developed for demanding applications where reliability and safety are top priorities. With medical approval in accordance with EN 60601-1, it is ideal for use in the healthcare sector. The intelligent charging process ensures gentle and complete charging of lead-acid, AGM and gel batteries, maximising their service life and making the device the ideal choice for professional users.Highlights at a glanceMedical approval: Certified to EN 60601-1 (3rd edition) for safe use in medical environments.Intelligent 3-stage charging: Fully automatic charging cycle with boost, timer and trickle charging for optimum battery care.High flexibility: Suitable for all common 12V lead-acid batteries (wet, gel, AGM).Robust design: Protection class IP41 offers protection against the ingress of foreign bodies and dripping water.Universal input: Wide range input (90-264 VAC) for worldwide use.Comprehensive protection: Protected against reverse polarity, short circuit and overheating.Precise charging technology for maximum battery lifeThe Mascot 2040 utilises a proven 3-stage charging process. Firstly, the battery is quickly charged with a constant current (4A). As soon as the final charging voltage is reached, a timer keeps the voltage constant in order to achieve full saturation. Finally, the device switches to trickle charging, which keeps the battery permanently full without overcharging. This prevents sulphation and ensures that your devices are always ready for use.Safety for sensitive applicationsThanks to its medical certification, this charger is ideal for use with patient lifts, mobile care chairs, medical carts and other battery-powered devices in hospitals and care homes. The high degree of protection and robust design ensure safe operation even under demanding conditions. LED indicators provide clear information about the current charging status at all times. Features ModelMascot 2040 (12V / 4A) - Medical ApplicationCharger for lead-acid batteries (gel, AGM, wet) in medical environments Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)14.7 V / 13.8 V Charging current4 A Charging method3-stage (Boost, Timer, Float) Medical approvalsEN 60601-1-2 (EMC), EN 60601-1 (Safety), UL 60601-1 Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)135 x 80 x 44 Weight (g)approx. 350  FAQs about the Mascot 2040 chargerWhich battery types is the charger suitable for?The Mascot 2040 is suitable for all types of 12V lead-acid batteries. This includes classic lead-acid wet batteries, maintenance-free AGM batteries (fleece) and gel batteries.What does the medical approval EN 60601-1 mean?This standard specifies strict safety requirements for medical electrical equipment. A charger with this approval fulfils increased requirements for electrical insulation and electromagnetic compatibility in order not to endanger patients and medical personnel and not to interfere with other medical devices.Can I leave the charger permanently connected?Yes, this is possible without any problems. Once the main charge is complete, the device automatically switches to float charge mode. In this mode, the self-discharge of the battery is compensated without overcharging or damaging it.Which plugs are available on the charger?The charger is often supplied with interchangeable DC plugs or a specific plug (e.g. 3-pin XLR) as standard, depending on the configuration. Please check the exact delivery details to ensure that the connection is suitable for your battery.

The Mascot 9740-12 is a robust and powerful desktop charger for 12V lead-acid battery systems. With a charging current of 10 amps and the proven 3-stage charging characteristic, it ensures fast and reliable charging even for larger battery capacities. Thanks to its medical approval (EN 60601-1) and protection class IP21, this device is a safe choice for professional use in medical technology and in industrial applications that utilise a stable 230V supply.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle with timer control ensures gentle fast charging and maximum battery life.Medical approval: Certified according to EN 60601-1 (3rd edition) for safe operation in medical environments.High performance: With a charging current of 10 amps, it provides enough power to get batteries ready for use again quickly.Dedicated input: Designed for an input voltage range of 198 - 264 VAC, ideal for stable 230V networks.Solid protection (IP21): The housing offers protection against solid foreign objects (>12mm) and vertically falling dripping water.Clear status display: A 3-colour LED display (orange/yellow/green) provides information about the current charging status at a glance.Precise charging technology for 12V systemsThe Mascot 9740 utilises an efficient 3-stage charging process (3-Step Charge). In the first phase (cycle), the device charges with a constant current of 10A until the final charging voltage of 14.7V is reached. This is followed by a timer-controlled phase with constant voltage to ensure complete saturation of the battery chemistry. Finally, the device switches to trickle charging (float at 13.7V) to keep the battery fully charged and ready for use.Ideal for medical and industrial applicationsThis charger was developed for applications that require reliability. It is perfect for power wheelchairs, larger patient lifts or industrial cleaning machines. The combination of high charging power and medical certification makes it a proven solution for critical systems. Features ModelMascot 9740 (12V / 10A) ApplicationCharger for medium to large lead-acid batteries (gel, AGM, wet) Input voltage190 - 264 V AC (47-63 Hz) Charging voltage (cycle / float)14.7 V / 13.8 V Charging current10 A Charging method3-stage (boost, timer, float) Indicators3-colour LED (red=charge, orange=timer, green=float) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)184 x 171 x 54 Weight (kg)approx. 1.6  FAQs about the Mascot 9740-12 chargerWhat does the input voltage range 198-264V mean?This range indicates that the charger is specifically optimised for operation on European 230V networks (or comparable voltages). It is not suitable for use on 110V networks (e.g. USA), but often offers more robust performance in the intended voltage range.Can I leave the charger permanently connected to the battery?Yes, the Mascot 9740 is designed for continuous operation. Once the charging process is complete, the device switches to maintenance charging mode (float, 13.7V). This compensates for self-discharge and keeps the battery fresh without exposing it to thermal stress.For which battery capacities is it suitable?Due to the high charging current of 10 amps, this device is ideal for 12V batteries with a capacity between approx. 40 Ah and 200 Ah. Smaller batteries should only be charged if they are approved for such high charging currents.What do the LED colours mean?Orange: Main charging with maximum current (the battery will be charged quickly).Yellow: Timer phase with constant voltage (saturation phase).Green: Maintenance charge (battery is full and can be removed or left connected).

The Mascot 2044 (model 2044-48) is a high-quality desktop charger, specially developed for 48V lead-acid battery systems in professional and medical applications. With a charging current of 0.9 A and an intelligent 3-stage charging profile, it ensures gentle, safe and complete charging of lead-acid, AGM and gel batteries. Thanks to its robust construction and medical approval (EN 60601-1), it is the ideal choice for demanding environments where reliability is key.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle with main charge, timer-controlled post-charge and trickle charge.Medical approval: Certified according to EN 60601-1 (3rd Edition) for safe use in medical environments.High compatibility: Suitable for all common 48V lead-acid batteries, including maintenance-free gel and AGM types.Universal input: Wide-range input (90-264 VAC) enables worldwide use without switching.Comprehensive protection: Protected against reverse polarity, short circuit and overheating for safe operation.Status display: A 3-colour LED (orange, yellow, green) indicates the current charging status at a glance.Precise charging technology for 48V systemsThe Mascot 2044 uses a proven 3-stage charging process to optimally supply 48V battery packs. First, the battery is charged with constant current (cycle). As soon as the final charging voltage is reached, a timer keeps the voltage constant to achieve full saturation of the cells. Finally, the device switches to a maintenance charge (float), which keeps the battery permanently at 100% without overcharging and prevents sulphation.Ideal for industry and medical technologyWith its compact design and high reliability, this charger is ideal for electric scooters, rehabilitation equipment, mobile workstations or industrial measuring devices that run on 48V. Compliance with strict medical standards guarantees that the device can also be used safely in sensitive areas. Features ModelMascot 2044 (48V / 0.9A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)58.8 V / 54.8 V Charging current0.9 A Charging method3-stage (Boost, Timer, Float) Protective functionsReverse polarity protection, short-circuit protection Indicators3-colour LED (charge status) Dimensions (L x W x H in mm)135 x 80 x 44 Weight (g)approx. 350  FAQs about the Mascot 2044-48 chargerWhich battery types is the charger suitable for?The Mascot 2044-48 is suitable for all types of 48V lead-acid batteries. These include classic lead-acid wet batteries, maintenance-free AGM batteries (fleece), and gel batteries. It is not suitable for lithium-ion batteries.What do the colours of the LED display mean?Orange: The battery is being charged with constant current (main charge). Yellow: The final charging voltage has been reached, the timer is running (saturation phase). Green: The charging process is complete, the device is in float charging mode.Can I leave the charger connected permanently?Yes, this is easily possible. After completion of the main charging, the device automatically switches to the float charging mode. In this mode, the self-discharge of the battery is compensated, without overcharging or damaging it.What battery size can I charge with it?With a charging current of 0.9 A, this device is ideal for small to medium 48V battery packs with a capacity of about 4 Ah to 20 Ah. With larger batteries the charging time increases accordingly. 

The Mascot 2240-48 is an extremely compact and flexible desktop charger for 48V lead-acid battery systems. Despite its small size, it offers Mascot’s high-quality, intelligent 3-stage charging technology, which ensures gentle charging for lead-acid, gel and AGM batteries. The modular plug system (AC-X and DC-X) allows the device to adapt to a wide range of international standards and device ports on both input and output, making it the perfect solution for universal applications and maintenance charging.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle (Cycle, Timer, Float) for gentle charging and maximum battery life.AC-X input system: Interchangeable mains plugs enable worldwide use without the need to stock separate country versions.DC-X output system: Interchangeable secondary plugs (snap-lock or jack) for flexible adaptation to various charging sockets.Ideal for 48V systems: Designed for small 48V battery packs or for permanent maintenance charging of larger systems.Safe operation: Comprehensive protection against reverse polarity and short circuit as well as an LED status display.Robust design: Compact housing, certified to IP40 (optional IP41) for safe use.Maximum flexibility through interchangeable plugsThe Mascot 2240-48 is consistently designed for adaptability. Thanks to the AC-X system, the charger can be operated worldwide by simply plugging in the appropriate mains adapter (e.g. EU, UK, US, AUS). At the same time, the DC-X system on the output cable allows for the charging plug to be changed quickly, with no soldering required. This greatly reduces the need to stock various country or device variants and provides a universal solution for service and export.Gentle battery care for long service lifeThe proven 3-stage charging characteristic guarantees that your 48V batteries are not only charged, but cared for. After the main charge, a timer-controlled phase ensures safe full charging before the device automatically switches to maintenance charging (float). This compensates for self-discharge and keeps the battery permanently ready for use without thermal stress.Reliability for professional applicationsMascot chargers are known for their durability and quality. The 2240-48 model is perfect for low-current applications or maintenance charging in backup systems, medical devices, or small electric vehicles operating at 48 volts. The LED display always clearly indicates the current status. Features ModelMascot 2240 (48V / 0.25A) AC-X/DC-X ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)58.8 V / 54.8 V Charging current0.25 A Charging method3-stage (Boost, Timer, Float) Special featureInterchangeable mains plug (AC-X) & output plug (DC-X) Protective functionsReverse polarity protection, short circuit protection Dimensions (L x W x H in mm)90 x 45 x 32 Weight (g)approx. 115  FAQs about the Mascot 2240-48 chargerWhat do AC-X and DC-X mean?AC-X and DC-X are the designations for Mascot’s flexible plug system. AC-X means that the mains plug (for the socket) is interchangeable (clip system). DC-X means the plug to the battery can also be changed to adapt it to different device ports.What battery sizes is the device suitable for?The 2240-48 supplies a charging current of 0.25 A. It is therefore ideal for small 48V batteries (approx. 1 Ah to 6 Ah) or for maintenance charging of larger 48V systems to compensate for self-discharge.Are the interchangeable plugs included in the delivery?That depends on the specific item configuration. The charger is often supplied as a basic unit and the required AC and DC plugs must be ordered separately depending on the application. Please check the exact contents of your set.Can I leave the charger connected permanently?Yes. Once the battery is fully charged, the device switches to maintenance charging. The battery can remain connected to the charger for a long period to maintain full capacity (e.g. during winter storage).

The Mascot 2245-24 is a high-quality and powerful desktop charger for 24V lead-acid battery systems. With a charging current of 2.2 amps and proven 3-stage charging characteristics, it ensures fast, safe and battery-friendly charging. Thanks to its medical approval (EN 60601-1) and robust workmanship, it is the first choice for demanding applications in medical technology, rehabilitation and industry where reliability is essential.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle with timer control for maximum battery life.Medical approval: Certified to EN 60601-1 (3rd edition) for use in medical environments.Universal input: Wide-range input (90-264 VAC) enables worldwide use.Versatile compatibility: Suitable for all 24V lead-acid batteries (wet, gel, AGM).Safe operation: Protected against reverse polarity, short circuit and overheating.Clear status display: 3-colour LED display (orange/yellow/green) indicates the current charging progress.Precise charging technology for 24V systemsThe Mascot 2245 utilises a sophisticated 3-stage charging process. In the first phase (cycle), the battery is quickly charged with a constant current of 2.2A. Once the final charging voltage has been reached, a timer-controlled phase ensures that the cell chemistry is fully saturated. Finally, the device switches to float charging to keep the battery permanently at 100% capacity without subjecting it to thermal stress.Ideal for medical and industrial applicationsThis charger has been specially designed for professional use. It is ideal for charging electric wheelchairs, patient lifts, mobile ward trolleys or industrial cleaning machines. Compliance with strict safety standards guarantees that the device can also be operated safely in sensitive areas. Features ModelMascot Lead-acid battery charger (24V / 2.2A) - Type 2541/2542 ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (cycle / float)29.4 V / 27.6 V Charging current2.2 A Charging method3-stage (boost, timer, float) Indicators3-colour LED (red=charge, orange=timer, green=float) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)107 x 67 x 36.5 (desktop version 2541) Weight (g)approx. 250  FAQs about the Mascot 2245-24 chargerCan I leave the charger permanently connected to the battery?Yes, the Mascot 2245 is designed for continuous operation. As soon as the battery is full, it switches to float charge mode, which compensates for self-discharge and keeps the battery ready for use.Which plugs does the device have?Mascot chargers in the 2245 series are often equipped with interchangeable DC plugs (via hollow plug system or fixed cable). The mains input is usually via a standard socket (e.g. C8 small appliance plug), which makes it possible to change the mains cable for different countries. Please check the exact scope of delivery.What battery capacities is it suitable for?With a charging current of 2.2 amps, the device is ideal for batteries with a capacity of between approx. 8 Ah and 60 Ah. It can also charge larger batteries, but the charging time will then be correspondingly longer.What do the LED colours mean?Orange: Fast charging with constant current. Yellow: Timer phase with constant voltage (battery almost full). Green: Float charge (battery full and ready for use).

The Mascot 2541-12 is a high-quality and flexible desktop charger for 12V lead-acid battery systems. With a charging current of 2.2 amps and the proven 3-stage charging characteristic, it ensures efficient and battery-friendly charging. Thanks to its medical approval (EN 60601-1) and protection class IP41, it is the ideal solution for demanding applications in medical technology and care, where maximum safety and reliability are required.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle with timer control for maximum battery life and optimal full charge.Medical approval: Certified to EN 60601-1 (3rd edition) for safe use in the medical patient environment.Flexible plug system (DC-X): Equipped with a snap-lock coupling that enables tool-free changing of different output plugs.Universal input (AC-X): Wide-range input (90-264 VAC) with exchangeable mains lead for worldwide use.Increased protection (IP41): The housing provides protection against solid foreign objects (>1mm) and vertically falling dripping water.Clear status indication: 3-colour LED display (orange/yellow/green) intuitively indicates the current charging progress.Precise charging technology for 12V systemsThe Mascot 2541 uses an advanced 3-stage charging method (3-Step Charge). In the first phase (Cycle), the battery is charged with a constant current of 2.2A until the end-of-charge voltage of 14.7V is reached. This is followed by a timer-controlled phase that holds the voltage to ensure full saturation of the battery chemistry. Finally, the device switches to maintenance charging (Float at 13.7V) to keep the battery permanently ready for use without overcharging it.Ideal for medical and demanding applicationsThis charger has been specially developed for professional environments. It is ideally suited for medical devices such as patient lifts, suction pumps or mobile care trolleys. With its combination of medical certification and IP41 protection class, it also provides reliable power supply in sensitive industrial environments. Characteristics ModelMascot 2541 (12V / 2.2A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)14.7 V / 13.7 V Charging current2.2 A Charging method3-stage (Boost, Timer, Float) Indicators3-colour LED (Red=charging, Orange=timer, Green=maintenance) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)107 x 67 x 36.5 Weight (g)approx. 250  FAQs about the Mascot 2541-12 chargerWhat does AC-X and DC-X mean?AC-X stands for the flexibility of mains input; the device uses an interchangeable mains cable (IEC C8 socket), so that it can be operated worldwide with the appropriate country plug. DC-X refers to the output cable with a snap-lock coupling. Various adapters (crocodile clips, XLR plugs, barrel plugs) can simply be plugged in here, without the need for soldering.Can I leave the charger permanently connected to the battery?Yes, the Mascot 2541 is designed for continuous operation. As soon as the battery is full, the device activates maintenance charge mode (Float, 13.7V), which compensates for natural self-discharge and keeps the battery in optimum condition.For which battery capacities is it suitable?With a charging current of 2.2 amps, this device is recommended for 12V batteries with a capacity between approx. 10 Ah and 60 Ah. Smaller batteries could be charged too quickly, whereas with very large batteries the charging time increases.What do the LED colours mean?Orange: Main charging with maximum current (battery is being charged).Yellow: Timer phase with constant voltage (battery approaches full charge)Green: Maintenance charging (charging process complete, battery is full).

The Mascot 2541-24 is a reliable and compact desktop charger for 24V lead-acid battery systems. With a charging current of 1.2 amps and the proven 3-stage charging characteristic, it enables gentle and safe charging. The combination of medical certification (EN 60601-1) and protection class IP41 makes it the perfect choice for use in sensitive areas of medical technology and care, where safety is the top priority.Highlights at a glanceIntelligent 3-stage charging: Fully automatic charging cycle with timer control ensures optimum saturation and maximises the service life of the battery.Medical approval: Meets the strict requirements of the EN 60601-1 standard (3rd edition) for use in the direct patient environment.Flexible plug system (DC-X): Features a snap-lock coupling that allows different output plugs to be exchanged easily and without tools.Universal input (AC-X): Thanks to the wide-range input (90-264 VAC) and interchangeable mains cable, the device can be used worldwide.Increased protection (IP41): The robust housing is protected against solid foreign bodies (>1mm) and vertically falling dripping water.Clear status display: A 3-colour LED display (orange/yellow/green) provides information about the current charging status at all times.Precise charging technology for 24V systemsThe Mascot 2541 uses an advanced 3-stage charging process (3-Step Charge) that is specially designed for lead-acid batteries. In the first phase (cycle), the device charges with a constant current of 1.2A until the final charging voltage of 29.4V is reached. This voltage is then maintained in a timer-controlled phase to ensure that the cells are fully saturated. Finally, the charger switches to trickle charging (float at 27.4V), which ensures that the battery remains fully charged without being damaged.Ideal for medical and demanding applicationsThis model was designed for professional applications. It is ideal for supplying power to small medical devices, mobile care units or rehabilitation technology. Thanks to its certification to medical standards and IP41 protection class, it guarantees safe and trouble-free operation even in critical environments. Features ModelMascot 2541 (24V / 1.2A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage90 - 264 V AC (47-63 Hz) Charging voltage (cycle / float)29.4 V / 27.6 V Charging current1.2 A Charging method3-stage (boost, timer, float) Indicators3-colour LED (red=charging, orange=timer, green=trickle) Protective featuresReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)107 x 67 x 36.5 Weight (g)approx. 250  FAQs about the Mascot 2541-24 chargerWhat do AC-X and DC-X mean?AC-X refers to the flexible mains input; the device has an IEC C8 socket for interchangeable mains cables, which facilitates worldwide use. DC-X stands for the output cable with snap-lock coupling, to which various adapters (such as XLR, hollow plugs or clamps) can be easily connected.Can I leave the charger permanently connected to the battery?Yes, the Mascot 2541 is suitable for continuous connection. After a full charge, it automatically switches to trickle charge mode (float, 27.4V), which compensates for self-discharge and gently keeps the battery at 100%.For which battery capacities is it suitable?With a charging current of 1.2 amps, this device is best suited for 24V batteries with a capacity between approx. 5 Ah and 30 Ah. For significantly larger capacities, the charging time is extended accordingly.What do the LED colours mean?Orange: Main charge with maximum current (battery is charged).Yellow: Timer phase with constant voltage (battery is almost full).Green: Trickle charge (charging process completed, battery is ready for use).

The Mascot 2840-12 is a powerful and robust desktop charger for 12V lead-acid battery systems. With a high charging current of 8.5 amps and the proven 3-stage charging characteristic, it ensures fast and efficient charging even for larger battery capacities. Thanks to its medical approval (EN 60601-1) and protection class IP41, it fulfils the highest safety standards and is ideal for professional use in medical technology, rehabilitation and industry.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle with timer control ensures gentle fast charging and maximum battery life.Medical approval: Certified to EN 60601-1 (3rd edition) for safe operation in medical environments and in the vicinity of patients.Flexible plug system (DC-X): Equipped with the practical Snap-Lock coupling for tool-free changing of various output plugs (e.g. XLR, terminals).Powerful: With a charging current of 8.5 amps, it offers sufficient reserves for larger batteries and shorter charging times.Universal input: Can be used worldwide thanks to its wide-range input (90-264 VAC) and interchangeable mains cable (IEC C8).Increased protection (IP41): The housing is protected against solid foreign bodies (>1mm) and vertically falling dripping water.Clear status display: The 3-colour LED display (orange/yellow/green) provides information about the charging status at a glance.Precise charging technology for 12V systemsThe Mascot 2840 utilises an efficient 3-stage charging process (3-Step Charge). In the first phase (cycle), the device charges with a constant current of 8.5A until the final charging voltage of 14.7V is reached. This is followed by a timer-controlled phase with constant voltage to ensure complete saturation of the battery chemistry. Finally, the device switches to trickle charging (float at 13.7V) to keep the battery fully charged and ready for use.Ideal for medical and demanding applicationsThis charger has been developed for applications that require high performance and reliability. It is perfect for power wheelchairs, larger patient lifts, scooters or industrial cleaning machines. The combination of high charging power, medical certification and IP41 protection class makes it a versatile solution for critical systems. Characteristics ModelMascot 2840 (12V / 8.5A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage198 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)14.7 V / 13.8 V Charging current8.5 A Charging method3 stages (boost, timer, float) Indicators3-colour LED (red=charging, orange=timer, green=trickle) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)135 x 80 x 44 Weight (g)approx. 450  FAQs about the Mascot 2840-12 chargerWhat does DC-X mean?DC-X refers to the flexible output cable system with a snap-lock coupling. Instead of a permanently installed plug, various adapters (such as 3-pin XLR for wheelchairs, hollow plugs or crocodile clips) can simply be plugged in without the need for soldering.Can I leave the charger permanently connected to the battery?Yes, the Mascot 2840 is designed for continuous operation. As soon as the charging process is complete, the device switches to trickle charge mode (float, 13.7V). This equalises self-discharge and keeps the battery fresh without placing it under thermal stress.For which battery capacities is it suitable?Thanks to the high charging current of 8.5 amps, this device is ideal for 12V batteries with a capacity of between approx. 40 Ah and 200 Ah. Very small batteries (under 20 Ah) should be charged with a weaker charger to protect the cells.What do the LED colours mean?Orange: Main charge with maximum current (battery is charged quickly).Yellow: Timer phase with constant voltage (saturation phase).Green: Trickle charge (battery is full and can be removed or left connected). 

The Mascot 2840-24 is a powerful and reliable desktop charger for 24V lead-acid battery systems. With a charging current of 4.5 amps and the proven 3-stage charging characteristic, it ensures fast and gentle charging. The combination of medical certification (EN 60601-1) and protection class IP41 makes this device the first choice for demanding applications in medical technology, care, and industry, where safety and durability are crucial.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle with timer control guarantees optimum saturation of the battery and extends its service life.Medical approval: Meets the strict safety requirements of the EN 60601-1 standard (3rd edition) for use in the direct patient environment.Flexible plug system (DC-X): Equipped with the Snap-Lock coupling, which allows different output plugs (e.g. XLR, hollow plug) to be changed easily and without tools.High performance: With 4.5 amps charging current, it offers an ideal balance between charging speed and battery protection for medium to large capacities.Universal input: Thanks to the wide range input (90-264 VAC) and exchangeable mains cable (IEC C8), the device can be used worldwide.Increased protection (IP41): The robust housing reliably protects the electronics from solid foreign objects (>1mm) and vertically falling drip water.Clear status display: A 3-colour LED display (orange/yellow/green) always provides intuitive information about the current charging status.Precise charging technology for 24V systemsThe Mascot 2840 uses a specially tuned 3-stage charging process (3-Step Charge). In the first phase (Cycle), the device charges with a constant current of 4.5A until the charging voltage of 29.4V is reached. This is followed by a timer-controlled phase in which the voltage is kept constant in order to fully saturate the cells. Finally, the charger switches to float charge (Float at 27.4V), which keeps the battery permanently at 100% capacity without damage.Ideal for medical and demanding applicationsThis model has been specially designed for professional use. It is the perfect power supply for electric wheelchairs, scooters, mobile care trolleys or patient hoists that are operated with 24V systems. The certification according to medical standards ensures maximum safety even in sensitive areas. Characteristics ModelMascot 2840 (24V / 4.5A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage198 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)29.4 V / 27.6 V Charging current4.5 A Charging process3 stages (Boost, Timer, Float) Display3-colour LED (Red=Charge, Orange=Timer, Green=Float) Protective functionsReverse polarity protection, short circuit protection Dimensions (L x W x H in mm)135 x 80 x 44 Weight (g)approx. 450  FAQs about the Mascot 2840-24 chargerWhat does DC-X mean?DC-X stands for the flexible output cable system with a Snap-Lock coupling. Instead of a permanently attached plug, a variety of adapters (such as the commonly used 3-pin XLR plug in rehab technology, but also crocodile clips or hollow plugs) can simply be plugged in.Can I leave the charger permanently on the battery?Yes, the Mascot 2840 is designed for continuous operation. After the main charge is complete, it automatically switches to float charge mode (Float, 27.4V), which compensates for natural self-discharge and keeps the battery ready for use.For which battery capacities is it suitable?With a charging current of 4.5 amps, this device is ideal for 24V batteries with a capacity between approx. 20 Ah and 120 Ah. It can also charge larger batteries, although the charging time accordingly increases.What do the LED colours mean?Orange: Main charge with maximum current (battery is charging).Yellow: Timer phase with constant voltage (saturation phase, battery almost full)Green: Float charge (charging process complete, battery full).

The Mascot 2840-36 is a high-quality desktop charger that has been specially developed for 36V lead-acid battery systems. With a charging current of 2.3 amps and the proven 3-stage charging characteristic, it offers reliable and battery-friendly power supply. Thanks to medical certification (EN 60601-1) and protection class IP41, this device is ideally suited for demanding applications in medical technology, rehabilitation, as well as industrial environments.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle with timer control ensures optimum saturation of the battery and maximises its service life.Medical certification: Meets the stringent safety requirements of the EN 60601-1 standard (3rd edition) for safe use in patient environments.Flexible plug system (DC-X): Equipped with Snap-Lock coupling, allowing quick and tool-free swapping of various output plugs (e.g. XLR, hollow plug).Universal input: Thanks to wide-range input (90-264 VAC) and interchangeable mains cable (IEC C8), the device can be used worldwide without problems.Enhanced protection (IP41): The housing is robust and protected against solid foreign objects (>1mm) as well as vertically dripping water.Clear status indicator: A 3-colour LED indicator (orange/yellow/green) intuitively shows the current charging progress.Precise charging technology for 36V systemsThe Mascot 2840 uses an advanced 3-stage charging method (3-Step Charge) to optimally charge 36V lead-acid batteries. In the first phase (cycle), the device charges with constant current of 2.3A until the final charging voltage of approx. 44.1V is reached. This is followed by a timer-controlled phase in which the voltage is kept constant to ensure that the cells are fully saturated. Finally, the charger switches to float charging (at approx. 41.1V), keeping the battery permanently ready for use without overcharging.Ideal for medical and demanding applicationsThis model is the perfect choice for professional use. It is ideal for powering 36V systems in rehab technology (e.g. scooters, electric wheelchairs), for mobile medical devices or industrial applications. The combination of medical certification and protection class IP41 ensures top safety and reliability. Features ModelMascot 2840 (36V / 3.0A) ApplicationCharger for lead-acid batteries (gel, AGM, wet) Input voltage198 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)44.1 V / 41.4 V Charging current3.0 A (standard for model 2840-36) Charging method3-stage (Boost, Timer, Float) Indicators3-colour LED (Red=Charging, Orange=Timer, Green=Float) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)135 x 80 x 44 Weight (g)approx. 450  FAQs about the Mascot 2840-36 chargerWhat does DC-X mean?DC-X stands for the flexible output cable system with Snap-Lock coupling. Instead of a permanently installed plug, various adapters (e.g. 3-pin XLR, hollow plug or crocodile clips) can simply be plugged on without soldering.Can I leave the charger permanently on the battery?Yes, the Mascot 2840 is designed for continuous operation. After completion of the main charge, it automatically switches to float charging mode, which compensates for natural self-discharge and keeps the battery at 100% gently.For which battery capacities is it suitable?With a charging current of 2.3 amps, this device is ideal for 36V batteries with a capacity between approx. 10 Ah and 60 Ah. Larger capacities can also be charged, but will take correspondingly longer.What do the LED colours mean?Orange: Main charge with maximum current (battery is charging).Yellow: Timer phase with constant voltage (saturation phase, battery almost full)Green: Float charge (charging process complete, battery is full).

The Mascot 9740-24 is a proven and long-lasting desktop charger for 24V lead-acid battery systems. With a charging current of 5 amperes and reliable 3-stage charging characteristics, it provides safe energy supply for medium to larger battery capacities. Thanks to medical approval (EN 60601-1) and protection class IP21, this device is ideally suited for use in sensitive areas of medical technology as well as for industrial applications operated on a 230V mains supply.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle (I-U-U) with timer control guarantees optimum full charging and keeps the battery maintained for a long service life.Medical approval: Certified according to EN 60601-1 (3rd edition) for safe use in patient environments.Reliable performance: With 5 amperes charging current, the device ensures efficient charging without thermally overloading the batteries.Dedicated input: Designed for an input voltage range of 198 - 264 VAC, optimised for European power grids.Reliable protection (IP21): The housing is protected against the ingress of solid foreign bodies (>12mm) and vertically falling dripping water.Clear status indication: The integrated 3-colour LED indicator (orange/yellow/green) provides information about the current charging process at all times.Precise charging technology for 24V systemsThe Mascot 9740 uses a battery-friendly 3-stage charging process. In the first phase (Cycle) the device charges with a constant current of 5A until the final charging voltage of 29.4V is reached. This is followed by a timer-controlled phase with constant voltage, to ensure full saturation of the cells. Finally, the charger switches to trickle charging (float at 27.4V), keeping the battery permanently at 100%.Ideal for medical and industrial useThis charger is designed for professional continuous use. It is the ideal power source for power wheelchairs, scooters, patient lifts or mobile medical trolleys. The combination of robust construction, medical safety and 230V optimisation makes it a reliable partner in everyday use. Features ModelMascot 9740 (24V / 5A) ApplicationCharger for medium to large lead-acid batteries (gel, AGM, wet) Input voltage190 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)29.4 V / 27.6 V Charging current5 A Charging procedure3-stage (Boost, Timer, Float) Indicators3-colour LED (Red=Charging, Orange=Timer, Green=Trickle) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)184 x 171 x 54 Weight (kg)approx. 1.6  FAQs about the Mascot 9740-24 chargerWhat does the input voltage range 198-264V mean?This range signals that the charger is optimised for 230V networks (as is usual in Europe). It is not suitable for operation on 110V networks (e.g. USA). This specialisation often allows a more robust construction of the input electronics for the intended market.Can I leave the charger permanently connected to the battery?Yes, the Mascot 9740 is suitable for permanent connection. After full charging, it automatically switches to trickle charging mode (Float, 27.4V), which compensates for the natural self-discharge and keeps the battery ready for use.For which battery capacities is it suitable?With a charging current of 5 amperes, this device is recommended for 24V batteries with a capacity between approx. 20 Ah and 120 Ah. It offers a balanced ratio between charging time and battery conservation.What do the LED colours mean?Orange: Main charge with maximum current (battery is being charged).Yellow: Timer phase with constant voltage (saturation phase, battery almost full)Green: Trickle charging (charging process complete, battery is full).

The Mascot 9740-36 is a powerful and safe desktop charger for 36V lead-acid battery systems. With a charging current of 3.3 amps and the proven 3-stage charging characteristic, it ensures reliable charging. The combination of medical certification (EN 60601-1) and protection class IP21 makes this device the ideal solution for professional use in medical technology, rehab technology, as well as in industrial applications that are operated on stable 230V networks.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle (I-U-U) with timer control ensures a gentle full charge that maximizes battery life.Medical approval: Meets the strict safety requirements of EN 60601-1 (3rd edition) standard for safe use in patient environments.Reliable performance: With a charging current of 3.3 amps, the device provides a stable power supply for 36V systems.Dedicated input: Designed for an input voltage range of 198 - 264 VAC, specially optimized for European 230V networks.Solid protection (IP21): The enclosure is protected against solid foreign objects (>12mm) and vertically falling dripping water.Clear status display: A 3-colour LED indicator (orange/yellow/green) intuitively indicates the current charging progress.Precise charging technology for 36V systemsThe Mascot 9740 uses a highly developed 3-stage charging process. In the first phase (cycle), the device charges at a constant current of 3.3A until the charging voltage of approx. 44.1V is reached. This is followed by a timer-controlled phase in which the voltage is kept constant to ensure full cell saturation. To finish, the charger switches to maintenance charging (float at approx. 41.1V), so the battery remains permanently ready for use without being overcharged.Ideal for medical and demanding applicationsThis model is ideally suited for powering 36V applications, which are frequently found in rehab technology (e.g. power wheelchairs, scooters) or in mobile medical devices. The robust design and adherence to medical standards ensure safe operation even in sensitive environments. Features ModelMascot 9740 (36V / 3.3A) ApplicationCharger for medium to large lead-acid batteries (gel, AGM, wet) Input voltage190 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)44.1 V / 41.4 V Charging current3.3 A Charging process3-stage (Boost, Timer, Float) Indicators3-colour LED (Red=Charging, Orange=Timer, Green=Maintenance) Protective functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)184 x 171 x 54 Weight (kg)approx. 1.6  FAQs about the Mascot 9740-36 chargerWhat does the input voltage range 198-264V mean?This range indicates that the charger is specially designed for 230V networks (as common in Europe). It is not suitable for worldwide use on 110V networks (e.g. USA), which often allows for a more robust design of components for the target market.Can I leave the charger permanently connected to the battery?Yes, the Mascot 9740 is designed for continuous operation. After the main charge is complete, it automatically switches to maintenance charging (float), which compensates for natural self-discharge and gently keeps the battery at 100%.What battery capacities is it suitable for?With a charging current of 3.3 amps, this device is ideal for 36V batteries with a capacity of approx. 15 Ah to 80 Ah. Charging is possible for larger capacities, but it will take correspondingly longer.What do the LED colours mean?Orange: Main charge with maximum current (battery is charging).Yellow: Timer phase with constant voltage (saturation phase, battery almost full)Green: Maintenance charging (charging process completed, battery is full).

The Mascot 9740-48 is a high-quality desktop charger specially designed for 48V lead-acid battery systems. With a charging current of 2.5 amps and the proven 3-stage charging characteristic, it ensures efficient and gentle charging. The combination of medical certification (EN 60601-1) and protection class IP21 makes this device the ideal choice for professional use in medical technology, e-mobility and industrial applications that are operated on stable 230V networks.Highlights at a glanceIntelligent 3-stage charging: The fully automatic charging cycle (I-U-U) with timer control ensures optimum saturation of the battery and maximises its service life.Medical approval: Meets the strict safety requirements of the EN 60601-1 standard (3rd edition) for safe use in the direct patient environment.Reliable performance: With a charging current of 2.5 amps, the device provides a stable power supply for 48V systems.Dedicated input: Designed for an input voltage range of 198 - 264 VAC, specially optimised for European 230V networks.Solid protection (IP21): The housing is protected against solid foreign objects (>12mm) and vertically falling dripping water.Clear status display: A 3-colour LED display (orange/yellow/green) provides intuitive information about the current charging progress.Precise charging technology for 48V systemsThe Mascot 9740 utilises a highly developed 3-stage charging process. In the first phase (cycle), the device charges with a constant current of 2.5A until the final charging voltage of approx. 58.8V is reached. This is followed by a timer-controlled phase in which the voltage is kept constant to ensure that the cells are fully saturated. Finally, the charger switches to trickle charging (float at approx. 54.8V), whereby the battery remains permanently ready for use without being overcharged.Ideal for medical and demanding applicationsThis model is ideal for powering 48V applications, such as those found in e-mobility (scooters, golf caddies), stair lifts or medical transport equipment. The robust design and compliance with medical standards ensure safe operation even in sensitive environments. Features ModelMascot 9740 (48V / 2.5A) ApplicationCharger for medium to large lead-acid batteries (gel, AGM, wet) Input voltage190 - 264 V AC (47-63 Hz) Charging voltage (Cycle / Float)58.8 V / 54.8 V Charging current2.5 A Charging method3-stage (boost, timer, float) Indicators3-colour LED (red=charging, orange=timer, green=float) Protection functionsReverse polarity protection, short-circuit protection Dimensions (L x W x H in mm)184 x 171 x 54 Weight (kg)approx. 1.6  FAQs about the Mascot 9740-48 chargerWhat does the input voltage range 198-264V mean?This range indicates that the charger is specially designed for 230V networks (as is usual in Europe). It is not suitable for worldwide use on 110V networks (e.g. USA), which often enables a more efficient design of the components for the target market.Can I leave the charger permanently connected to the battery?Yes, the Mascot 9740 is designed for continuous operation. Once the main charge is complete, it automatically switches to float charge mode, which compensates for natural self-discharge and keeps the battery gently at 100%.For which battery capacities is it suitable?With a charging current of 2.5 amps, this device is ideal for 48V batteries with a capacity of between approx. 10 Ah and 60 Ah. Charging is possible for larger capacities, but takes longer.What do the LED colours mean?Orange: Main charge with maximum current (battery is charged).Yellow: Timer phase with constant voltage (saturation phase, battery almost full).Green: Trickle charge (charging process completed, battery is full).

The Mascot 9541-12 is an extremely powerful high-frequency charger for professional and industrial applications. With an enormous charging current of up to 50 amps (often split into 2 channels of 25A each) and a robust metal housing, this device is designed for charging large battery banks or for parallel use. It dispenses with delicate design frills and focuses entirely on performance, reliability and durability under tough operating conditions.Highlights at a glanceEnormous charging power: Delivers up to 50A total current (or 2x 25A), ideal for battery capacities from 100 Ah to over 500 Ah.Dual-Output (X2): The device often has two separate outputs, allowing two 12V batteries to be charged independently of each other at the same time.Intelligent 3-stage charging: Processor-controlled charging curve (IUU) with timer ensures rapid main charging and safe maintenance charging.Temperature compensation: An external temperature sensor automatically adjusts the charging voltage to the ambient temperature in order to protect the battery in hot weather and to fully charge it in the cold.Industry standard: Robust metal chassis with active cooling (fan) and IP20 rating for workshop or switch cabinet use.Safe operation: Protected against reverse polarity, short circuit and overheating.Powerful technology for large capacitiesThe Mascot 9541 operates with efficient switched-mode power supply technology. The charging process takes place in three phases:Constant current (Boost): Charging with maximum current (e.g. 2x 25A) to quickly bring the battery up to approx. 80% capacity.Constant voltage (Timer): The voltage is kept at 14.7V while the current drops. A timer ensures that this phase lasts long enough to fully convert the lead crystals.Trickle charge (Float): Lowering the voltage to 13.7V. The battery can remain permanently connected (UPS operation, emergency generators).Ideal for workshop, marine and industryUnlike the compact desktop devices of the "Blueline" series, the 9541 is a real "workhorse". It finds its place in professional battery charging stations, on board ships, in motorhomes with large supply batteries or in industrial cleaning machines and forklift trucks. Features ModelMascot 9541 (12V / 50A) ApplicationIndustrial charger for large lead-acid batteries (gel, AGM, wet) Input voltage230 V AC (50-60 Hz) Charging voltage (Cycle / Float)14.7 V / 13.7 V (adjustable) Charging current50 A (configured as 2x 25A modules) Charging method3-stage (Boost, Timer, Float) FeaturesRobust metal housing, temperature-controlled fan, LED display Protective functionsReverse polarity protection, short-circuit protection, overheating protection Dimensions (L x W x H in mm)335 x 234 x 103 (approx.) Weight (kg)approx. 4.8  FAQs about the Mascot 9541-12 chargerWhat does "X2" or "2 outputs" mean?The 9541 model is often designed as a "dual charger." That means it has two independent charging outputs. You can either charge two 12V batteries at the same time (each with a maximum of 25A) or bridge the outputs (parallel operation) to charge a single large battery with the full 50A.Is the device waterproof?No, the 9541 has the IP20 rating. It is designed for dry indoor use, control cabinets or installation in vehicles/boats (in a protected position). It is not protected against water like the encapsulated IP67 models.H3: Do I need the temperature sensor?When charging currents of this magnitude are involved, it is highly recommended to use the temperature sensor. It is attached to the battery and reports the battery temperature to the charger so that the charging voltage can be finely adjusted. This prevents the battery from "boiling" at high ambient temperatures.What battery size is it suitable for?As a rule of thumb: Charging current approx. 10% to 25% of the battery capacity. With a charging current of 50A, the 9541 is ideal for battery banks of approx. 200 Ah to 500 Ah (or with 2x25A for two banks of 100-250 Ah).

The Mascot 9541-24 is an extremely powerful high-frequency charger, designed for professional applications that require reliable power supply for large 24V lead battery systems. With a maximum charging current of 25 amps and a robust metal housing, this device provides the necessary reserves for use in workshops, the marine sector or industrial facilities. It ensures fast recharging and precise battery maintenance through intelligent charging technology.Highlights at a glanceHigh charging power: Delivers up to 25 amps charging current, which allows fast charging of high capacity battery banks (e.g. in cleaning machines or boats).Intelligent 3-stage charging: The processor-controlled charging procedure (IUU) with timer function ensures optimum saturation of the battery and prevents harmful overcharging.Temperature compensation: The connection for an external temperature sensor enables the automatic adjustment of the charging voltage to the ambient temperature, which significantly increases the battery's lifespan.Industrial design: A robust metal chassis and an active fan cooling system make the device resistant for permanent use in demanding environments.Flexible output: Equipped with sturdy screw terminals for secure connection of thick charging cables; often also available as a version with two outputs (2x 12.5A).Comprehensive protection: The electronics are protected against short circuit, reverse polarity and overheating to ensure maximum operational safety.Powerful technology for large 24V batteriesThe Mascot 9541-24 operates with an efficient 3-stage characteristic. In the first phase (Boost), the battery is charged with a maximum current of 25A until the end-of-charge voltage (typically 29.4V) is reached. This is followed by the timer phase, during which the voltage remains constant while the current drops, ensuring that the chemical processes in the battery are fully completed. Finally, the device lowers the voltage to a safe level (float at 27.4V) to keep the battery permanently fully charged without "gassing" or water loss.Ideal for heavy duty, marine and automotiveThis charger is not a classic plug-in power supply, but a real powerhouse. It is perfectly suited for stationary use in charging rooms, for wall mounting in service vehicles or as an onboard charger on ships. It reliably supplies forklift batteries, aerial work platforms, or large emergency battery banks. Features ModelMascot 9541 (24V / 25A) ApplicationIndustrial charger for large lead-acid batteries (gel, AGM, wet) Input voltage230 V AC (50-60 Hz) Charging voltage (Cycle / Float)29.4 V / 27.4 V (adjustable) Charging current25 A Charging method3-stage (Boost, Timer, Float) FeaturesRobust metal housing, temperature-controlled fan, LED display Protective functionsReverse polarity protection, short-circuit protection, overheating protection Dimensions (L x W x H in mm)335 x 234 x 103 (approx.) Weight (kg)approx. 4.8  FAQs about the Mascot 9541-24 chargerIs the charger suitable for outdoor use?No, the device has protection class IP20. This means it is protected against contact and larger foreign objects, but not against water or moisture. It should be installed in dry indoor areas, control cabinets, or protected enclosures.For which battery capacity is it recommended?With 25 amps charging current, the device is ideal for battery capacities between approx. 100 Ah and 500 Ah. For smaller batteries (under 80 Ah), the charging current could be too high, which would strain the battery.Why does the device have a fan?At a charging power of 24V and 25A, heat is generated. The integrated fan provides active cooling for the power electronics to ensure stable performance even under continuous load. The fan is often temperature-controlled.What does the temperature sensor do?The (usually optional or included) sensor is attached to the battery. It measures the temperature of the battery. If the battery is hot, the charger lowers the voltage to avoid overheating. If it is very cold, the voltage increases slightly to ensure the battery still gets fully charged. This is very important for the longevity of large lead batteries.

This intelligent universal charger is the "all-in-one" solution for your fleet. Instead of using a separate charger for each HBC battery type (3.6V or 6V, small or large), this device automatically detects the inserted battery type and adjusts the charging current and voltage accordingly.It replaces the original HBC chargers (e.g. QE10860, QA10860, IL series) and is suitable for both older NiCd batteries as well as for modern NiMH batteries as well.Highlights at a GlanceMulti-voltage (3.6V & 6V): The charger automatically detects whether you have inserted a 3.6V battery (e.g. FuB 05AA) or a 6V battery (e.g. FuB 3A). No manual switches required.Multi-chemistry (NiCd & NiMH): You can charge mixed stocks. Whether old red/black NiCd battery or new orange NiMH battery – the charging electronics (Delta-U shut-off) safely controls the process and prevents overcharging.Dual-Power (230V & 12/24V): The delivery usually includes two cables included:Power supply unit for the socket (100-240V).Car adapter for the cigarette lighter (12V/24V) – ideal for charging in lorries, construction cranes or service vehicles.LED status display: Simple traffic light logic displays the status:Red: Battery is being fast-charged.Green: Battery is full (trickle charging active).(Optional depending on model: flashing in case of defect).Custom-fit charging cradle: The charging holder is shaped so that the standard HBC battery blocks (FuB 3A, FuB 05AA, FuB 9AA, FuB 10AA) make secure contact.Compatible Battery TypesThis charger covers the most common HBC batteries (please pay attention to the design):The "Small" (3.6V):BA225030, BA205030, BA205000 (FuB 05A, FuB 05AA)The "Flat" (6V):BA223030, BA203060, BA203061 (FuB 3A, FuB 03A)The "Compact 6V":BA209000, BA209060 (FuB 9A, FuB 9AA)The "Large" (6V):BA214060, BA214061, BA213020 (FuB 10AA, FuB 10XL, FuB 78AA)Note: For some universal chargers, an adapter is required for the very large FuB 10 block, or the housing is designed so that this also fits. Properties ModelUniversal quick charger for HBC Radiomatic Compatible battery typesBA225030, BA214060, BA214061, BA213020, FuB 05AA, FuB 10AA, FuB 10XL, FuB 78AA Chemical compatibility**NiCd** and **NiMH** (automatic detection) Voltage range**2.4V to 6.0V** (automatic switching) Charging currentapprox. **1000 mA to 1500 mA** (fast charge) Charging method**Delta-Peak / -dV monitoring** (prevents overcharging and “cooking” of the batteries) Input voltage**100-240V AC** (worldwide) & **12V-24V DC** (lorry electrical system) Status displayLED: Red (charging), Green (Full/trickle), Flashing (Defective/Error) Physical fitSuitable for the large rectangular blocks (FuB 05 / FuB 10 / FuB 78) RestrictionNot suitable for the small square FuB 9AA (requires adapter or other charging cradle) Safety featuresOverheating protection, short-circuit protection, reverse polarity protection FAQs about the Universal Crane ChargerHow long does it take to charge a 2000 mAh battery?That depends on the charging current. With a typical charging current of approx. 800–1000mA, charging a fully empty 2000 mAh battery takes about 2.5 to 3 hours. Once the battery is full, the device switches to “trickle charge” (Green). So you can also leave the battery in it overnight.Can I use this to charge batteries from other manufacturers?No. The charging cradle is mechanically specific for the contacts and case shapes of HBC Radiomatic. Batteries from Hetronic, Autec or Scanreco do not fit mechanically.My battery gets warm when charging. Is that normal?Yes. Especially towards the end of charging, NiMH batteries become warm to the touch. The intelligent charger detects this temperature rise (or the voltage drop) and then switches off. If the battery does become hot, the battery is probably defective (internal resistance too high).

This high-quality replacement charger is the ideal solution for quickly and gently recharging the batteries of your Palfinger crane remote controls. It is precisely adapted to the widely used 7.2 Volt Ni-MH and Ni-Cd battery packs that are used in most Palfinger and Scanreco controls (such as RC400, 590, 960 or EEA2512).Designed for the tough everyday working conditions of crane operators, this charger often offers dual power supply: it can be operated from both the regular 230V socket in the office or workshop, as well as via a 12V/24V vehicle adapter directly in the lorry. The intelligent microprocessor-controlled charging electronics (Delta-U cut-off) prevent overcharging of the batteries and significantly maximise their service life.Highlights at a glance100% Compatible: Perfect fit for the standard 7.2V batteries of Palfinger and Scanreco radio remote controls (crane controls).Intelligent charging electronics: Microprocessor-controlled charging cut-off (Delta-U) protects the battery from harmful overcharging and heat build-up.Flexible power supply: Thanks to the included power supply (100-240V) and vehicle charging cable (12V/24V) you can easily charge at home, in the workshop, or directly in the lorry cab.Clear status display: A clearly legible LED display reliably informs you of the current charging status (e.g. red for charging, green for full).Quickly ready for use: With an adapted charging current, your empty radio battery is quickly charged again, so that crane downtimes are minimised.Robust construction: The charging cradle is made of impact-resistant plastic and easily withstands vibrations in the vehicle.Areas of ApplicationThis charger is the most important accessory for operators of heavy machinery:Loader cranes: For the remote controls of Palfinger loader cranes on lorries.Forestry: For timber forwarding cranes and harvesters equipped with Scanreco radio technology.Construction machinery: For powering the control units of concrete pumps or aerial work platforms with compatible 7.2V battery systems.Assembly & Safety InstructionsMaintain contacts: The working environment on construction sites is often dusty. Wipe the gold contacts on the charging cradle and the battery regularly with a dry cloth to avoid charging problems due to contact resistance.Vehicle operation: If you use the charger permanently in the lorry, make sure it is securely fixed and does not fly through the cab in the event of an emergency stop.Temperature: Do not charge the batteries in the blazing sun behind the windscreen. Extreme heat damages the cells during charging.End of charging: Even though the device has automatic disconnection, it is advisable to remove the battery from the cradle after full charge (green LED) if it is not required for a long time. Features Model compatibilitySuitable for **Palfinger / Scanreco** Supported battery types**NiMH** (Nickel-Metal Hydride) Replaces original chargerScanreco type 434 / 435 / EE0-159 Input voltage100 V - 240 V AC (wide range) Output voltageOptimised for **7.2 V battery packs** Charging currentapprox. 500 mA - 800 mA Charging methodDelta-U cut-off (microprocessor) CertificationsCE, RoHS Special featureShort circuit & reverse polarity protection  FAQs about the Palfinger chargerDoes this charger fit my Palfinger EEA2512 battery?Yes, absolutely. The battery type EEA2512 (as well as models 590, 960, 790 and RC400) is the standard battery in this radio control series. This charger is exactly designed for the shape and 7.2 volt voltage of these Ni-MH batteries.My old battery is still a Ni-Cd (Nickel-Cadmium) type. Will it also be charged?Yes. The charging electronics are backwards compatible and reliably recognise the voltage curve. You can use this charger to charge both older Ni-Cd batteries and the newer and more environmentally friendly Ni-MH (Nickel-Metal Hydride) batteries.How long does a complete charging process take?This depends on the capacity (Ah) of your battery. A typical replacement battery, for example with 2000 mAh (2.0 Ah), generally requires approx. 2 to 3 hours with this quick charger to become fully recharged.

This high-quality E-Bike Vision quick charger is the ideal solution for fast and safe charging of all 36V E-Bike Vision PowerPack (POP) batteries. With a charging current of 4 amps (4A), it charges your battery significantly faster than many standard chargers, thus minimising the waiting time until the next ride. The robust and compact design makes it the perfect charger for use at home, in the office, or on holiday.Highlights at a glanceFast charging: With a charging current of 4 amps, your E-Bike battery is charged quickly and efficiently.Universal compatibility: Suitable for all 36V E-Bike Vision PowerPack (POP) batteries.Intelligent charging electronics: Continuously monitors the charging process and automatically switches off after full charge to protect the battery.High safety: Comprehensive protection against short circuit, overheating and overvoltage.Compact and robust: Lightweight and durable housing, ideal for everyday use and on the go.Less Waiting, More RidingReduce charging time and maximise your time on the bike. With a charging current of 4 amps, this quick charger is significantly more powerful than many supplied 2A standard chargers. An empty battery with a capacity of 20Ah, for example, is fully ready for use again in only about 5 hours. The LED indicator provides clear and precise information about the current charging status at all times.Safe and gentle on your batteryDespite the high charging speed, the safety and longevity of your valuable battery take precedence. The intelligent charging electronics optimally adapt the charging process to the condition of the battery. After reaching full capacity, the device automatically switches to maintenance mode to prevent overcharging and maximise the lifespan of the battery cells.Flexibility for different systemsThis charger is the centrepiece of the flexible E-Bike Vision charging system. While it is directly compatible with the E-Bike Vision batteries for Panasonic 36V and Bosch Classic Line, it can also be used to charge original batteries of the Yamaha, Bosch (Active/Performance), and Panasonic (Next Generation) systems by means of separately available charging adapters. Features  ModelE-Bike Vision Quick Charger 36V 4A ApplicationCharger for 36V E-Bike batteries Input voltage100 - 240V AC Output voltage (V)42.0 Charging current (A)4 Connection (battery)System-specific charging adapter required DisplayLED status indicator Dimensions (L x W x H in mm)approx. 170 x 80 x 45 Weight (g)approx. 550  FAQs about the E-Bike Vision Quick ChargerWhat does 4A charging current mean and how does it affect the charging time?The "4A" stands for 4 amps charging current. This is the "speed" at which the battery is charged. A 4A charger charges a battery twice as fast as a standard 2A charger. The exact charging time is calculated by dividing the capacity of the battery (in Ah) by the charging current (in A), for example: 20 Ah / 4 A = 5 hours.Can I also use this charger to charge my original battery (e.g. from Yamaha)?Yes, this is possible. However, you need the appropriate, separately available charging adapter for your specific battery system (e.g. Yamaha PW series). The adapter establishes the correct mechanical and electrical connection to the charging port of your original battery.Is fast charging harmful for my battery?Modern lithium-ion batteries and their Battery Management Systems (BMS) are designed for fast charging with currents such as 4A or even 6A. The intelligent electronics in charger and battery ensure that charging is done safely and in the optimum range, so as not to negatively affect the lifespan of the cells.Can I leave the battery on the charger overnight?Yes, this is safe. The intelligent charger detects when the battery is fully charged and automatically ends the main charging process. It then switches to a maintenance mode with a very low current to keep the battery fully charged without overcharging it.

The Mascot 3546LI (12.6V) is an ultra-modern and efficient charger from the "Blueline" series, specially designed for 3-cell lithium-ion battery packs (3S, nominal voltage 10.8V/11.1V). With a charging current of 2.2 amps and a precise charging cut-off, it ensures a safe and fast full charge without stressing the sensitive lithium cells. Thanks to its medical approval (EN 60601-1 3rd edition) and compact design, it is the ideal choice for professional applications in medical technology and for high-quality industrial devices.Highlights at a glanceOptimised for Li-ion (3 cells): The charging characteristic is set precisely to the end-of-charge voltage of 12.6V to ensure maximum safety and performance for 3S batteries.Intelligent charge control: Utilises a 3-stage process (CC-CV cut-off) with current detection to end the charging process at exactly the right time.Medical certification: Meets the strict standards of EN 60601-1 (3.1 Ed) and EN 60601-1-2 (4th Ed) for use in the patient environment.Universal input: The wide-range input (90-264 VAC) enables worldwide operation; the mains cable or mains plug adapters are interchangeable.Versatile connections: Equipped with a flexible output (often snap-lock or hollow plug) that facilitates connection to a wide variety of battery sockets.Safety features: Comprehensive protection against reverse polarity, short circuits and charging battery packs with the wrong number of cells.Precise charging technology for lithium cellsThe Mascot 3546LI uses a charging characteristic that specifically protects the service life of lithium batteries:Constant current (CC): Charging with 2.2A (orange/yellow LED) until the cell voltage increases.Constant voltage (CV): The voltage is precisely maintained at 12.6V while the current slowly decreases until the battery is saturated.Charging end (Charge Complete): As soon as the current falls below a threshold value, the device switches off (0A) and the LED changes to green. There is no harmful continuous charging; however, the device monitors the voltage and restarts if necessary (restart at approx. 12.3V).Ideal for medical and mobile devicesThe combination of high efficiency, low weight (blueline housing) and medical safety makes this device perfect for mobile medical monitors, portable diagnostic devices, modern LED lights or measuring instruments that rely on lightweight lithium batteries. Features ModelMascot 3546 LI (12.6V / 2.2A) ApplicationCharger for 3-cell Li-ion batteries (nominal voltage 10.8V / 11.1V) Input voltage90 - 264 V AC (47-63 Hz) End of charge voltage12.6 V ± 0.1 V Charging current2.2 A Charging method3-stage (CC, CV, charge stop at current drop) ApprovalsMedically certified (EN 60601-1 Ed. 3.1) Protective functionsReverse polarity protection, short-circuit protection, safety timer Dimensions (L x W x H in mm)124 x 50 x 37 Weight (g)approx. 220  FAQs about the Mascot 3546LI chargerCan I also use it to charge lead or NiMH batteries?No. This charger is specifically designed for the voltage level (12.6V) and switch-off behaviour of lithium-ion batteries. Charging other chemistries can lead to overheating, incomplete charging or defects. Please use the corresponding Mascot "LA" (Lead Acid) or "NiMH" models.What does the LED display mean?Yellow/orange: The battery is charged with maximum current (main charge). Flashing yellow: The voltage has been reached, the battery is in the saturation phase (timer/CV). Green: The charging process is complete, the charging current is switched off. The battery is full.What connections does the device have?The 3546 model often has a modular design. On the input side, it usually has a 2-pin socket (IEC C8) for mains cables or interchangeable direct mains plug attachments. On the output side, the Mascot snap-lock system or a fixed cable with hollow plug (e.g. 2.1mm or 2.5mm) is often used. Please check the exact scope of delivery of your variant.Which battery size is it suitable for?With a charging current of 2.2A, the device is ideal for battery packs with a capacity of approx. 2 Ah to 20 Ah. Smaller batteries should tolerate a maximum charging current of more than 2.2A (check the data sheet of the cells).

The Mascot 3546LI (16.8V) is a compact and powerful charger from the proven "Blueline" series, specially designed for 4-cell lithium-ion battery packs (4S, nominal voltage 14.4V/14.8V). With a charging current of 1.8 amps and precise voltage regulation, it guarantees a safe and efficient full charge. Thanks to the medical approval (EN 60601-1 3rd edition) and the universal input voltage, this device is the perfect solution for medical applications and high-quality mobile devices used worldwide.Highlights at a glanceSpecialised for 4S Li-Ion: The charging characteristic is precisely fixed to a final charge voltage of 16.8V, which is crucial for the safe operation of 4-cell lithium batteries.Intelligent charge control: Operates with a process-controlled 3-stage method (CC-CV cut-off) including current monitoring to reliably prevent overcharging.Medical certification: Meets the high safety standards of EN 60601-1 (3.1 Ed) as well as EMC requirements for use in close proximity to patients.Universal input: The wide-range input (90-264 VAC) enables worldwide use; plugs or cables are often interchangeable (swap-clip system or C8 socket).High efficiency: State-of-the-art switch-mode power supply technology ensures low heat generation and low energy consumption.Comprehensive protection: The electronics are protected against short circuit, reverse polarity and overheating and detect faulty batteries.Precise charging technology for 4-cell packsThe Mascot 3546LI uses a charging process tailored to lithium chemistry to maximise the cycle life of your battery:Constant current (CC): The battery is charged with 1.8A (LED orange/yellow) until the voltage of 16.8V is reached.Constant voltage (CV): The voltage is held steady at 16.8V. The current decreases as the cells become saturated (LED often flashes yellow).End of charge (Charge Complete): If the charging current falls below a defined threshold, the device switches off the charging current (LED green). This prevents the "trickle charge" effect, which can be damaging for Li-Ion batteries. If the battery voltage later drops, the device automatically starts a new cycle.Ideal for medical and industrial useThanks to its certifications and compact design, this charger is ideal for portable medical devices (e.g. infusion pumps, mobile monitors), professional LED lighting systems or industrial handheld scanners powered by 14.4V/14.8V Li-Ion batteries. Features ModelMascot 3546 LI (16.8V / 1.8A) ApplicationCharger for 4-cell Li-Ion batteries (nominal voltage 14.4V / 14.8V) Input voltage90 - 264 V AC (47-63 Hz) End of charge voltage16.8 V ± 0.1 V Charging current1.8 A Charging method3-stage (CC, CV, charge stop on current drop) ApprovalsMedically certified (EN 60601-1 Ed. 3.1) Protective functionsReverse polarity protection, short circuit protection, safety timer Dimensions (L x W x H in mm)124 x 50 x 37 Weight (g)approx. 220  FAQs about the Mascot 3546LI 16.8V chargerWhat does "4S" or "4 cells" mean?"4S" stands for 4 lithium cells connected in series. Each cell has a final charge voltage of 4.2V. Multiplying this by 4 gives a total voltage of 16.8V, to which this charger is set.Can I use it to charge lead-acid batteries?No, under no circumstances. The charge curve and especially the cut-off voltage are specific for lithium-ion batteries. Attempting to charge lead-acid batteries may damage the battery and lead to dangerous situations.When is the battery fully charged?The battery is fully charged when the LED indicator lights green permanently. The device then switches off the charging current. You can now remove the battery or leave it connected (the device monitors the voltage in standby mode).What connectors are available?The 3546 model often offers interchangeable DC connectors (snap-lock or barrel connector system). The mains cable also is often modular (either as a swap-clip directly for the wall socket or as a desktop device with socket for a mains cable). Please check the details of your specific variant.

The Mascot 3546LI (29.4V) is a precise and reliable charger from the "Blueline" series, specially developed for 7-cell lithium-ion battery packs (7S, nominal voltage approx. 25.2V - 25.9V). With a charging current of 1.0 ampere and a precisely matched charging curve, it ensures a safe full charge that maximises the service life of your batteries. Thanks to medical approval (EN 60601-1 3rd Edition) and universal applicability, this device is the first choice for demanding applications in medical technology as well as professional industrial equipment.Highlights at a glanceOptimised for 7S Li-Ion: The charging characteristics are specifically set to a final charging voltage of 29.4V to safely and fully charge 7-cell lithium packs.Intelligent charge control: The 3-stage charge cycle (CC-CV shutdown) with current monitoring guarantees gentle charging and reliably prevents overcharging.Medical certification: Meets the strict safety requirements of EN 60601-1 (3.1 Ed) and is therefore approved for use in patient environments.Universal input: Thanks to wide-range input (90-264 VAC) and interchangeable mains plugs or mains cables (depending on configuration), the device can be used worldwide.Compact and efficient: State-of-the-art switching power supply technology ensures high efficiency with low heat generation and a compact design.High safety: Integrated protection circuits against reverse polarity, short circuit and thermal overload protect both the device and the battery.Precise charging technology for 7-cell packsThe Mascot 3546LI uses a 3-stage charging process optimised for lithium batteries:Constant current (CC): The battery is charged with a constant current of 1.0A (LED orange/yellow) until the charging final voltage of 29.4V is reached.Constant voltage (CV): The device keeps the voltage stable at 29.4V, while the current slowly drops to fully saturate the cells.End of charge (Charge Complete): Once the charging current drops below a defined threshold, the device switches off the charging current (LED green). This prevents the "trickle charge" effect that is harmful to lithium batteries. In the event of a voltage drop, a new cycle starts automatically.Ideal for medical and industrial useThis charger is ideally suited for powering medical devices such as patient lifts, mobile diagnostic devices or e-bikes and electric scooters which are based on 24V/25V Li-Ion systems (7 cells). Medical approval guarantees maximum reliability even in sensitive environments. Features ModelMascot 3546 LI (29.4V / 1.0A) ApplicationCharger for 7-cell Li-Ion batteries (nominal voltage 25.2V / 25.9V) Input voltage90 - 264 V AC (47-63 Hz) End of charge voltage29.4 V ± 0.1 V Charging current1.0 A Charging process3-stage (CC, CV, end of charge at current drop) ApprovalsCertified for medical technology (EN 60601-1 Ed. 3.1) Protection functionsReverse polarity protection, short-circuit protection, safety timer Dimensions (L x W x H in mm)124 x 50 x 37 Weight (g)approx. 220  FAQs about the Mascot 3546LI 29.4V chargerWhat does "7S" mean?"7S" stands for a series connection of 7 lithium-ion cells. As a single cell has a final charging voltage of 4.2V, the total pack results in a charging voltage of 29.4V (7 x 4.2V). This charger is set precisely to this.Can I use it to charge 24V lead-acid batteries?No. Although the voltages may appear similar, lead-acid batteries require a different charging curve and trickle charge. Using this Li-Ion charger with lead-acid batteries can cause damage. Please use the Mascot "LA" models (e.g. 2240 or 2541) for lead-acid batteries.When is the battery fully charged?The charging process is complete when the LED indicator lights up solid green. The device then switches off the charging current, as the battery is fully saturated.What connections are possible?The 3546 series is very flexible. On the input side, there are versions with a fixed mains cable or interchangeable mains plugs (interchangeable clips). On the output side, either the Mascot Snap-Lock system or a DC hollow plug is often installed. Please check the exact configuration of your model.

This versatile battery tester is the ideal diagnostic device for all users who work with a wide range of battery systems. With an extremely wide measuring range from 6V to 48V, it covers everything – from motorbikes, cars and lorries to electric scooters, golf caddies and solar storage systems. The device allows you to check battery voltage and state of charge in seconds, so you can immediately identify defective or discharged batteries and prevent failures.Highlights at a glanceExtreme voltage range: Usable for 6V, 12V, 24V, 36V and 48V batteries without manual switching.Precise status display: Reliably informs you about the current voltage and the estimated state of charge (SoC) of the battery.No separate battery required: The device supplies itself directly from the battery to be tested ("Powered by Test Object").High safety: Equipped with reverse polarity and overvoltage protection for safe application.Easy to use: Connecting the pole clamps is sufficient – the result is displayed immediately on the screen or via LEDs.Robust design: Shock-resistant housing, ideal for daily use in workshops, garages or mobile service.Versatile diagnostics for all battery typesWhether you want to check a small 6V vintage battery, a classic 12V car battery or a 48V drive battery from a forklift – this tester detects the applied voltage. It is optimised for all common lead technologies (standard lead-acid, gel, AGM). By regular monitoring, you can avoid deep discharges and significantly extend the lifetime of your batteries.Ideal for automotive, marine and industryThanks to the support of voltages up to 48V, this device is particularly valuable for users of e-mobility (e-scooters, rehab tech) and renewable energy (off-grid solar systems). It belongs in every toolbox to quickly rule out whether the battery is the cause of a starting problem or system failure in case of malfunction. Features ModelUniversal battery tester / monitor (6V - 48V) ApplicationPrecise monitoring of state of charge and voltage (automotive, solar, boat, industry) Measuring range (voltage)6V to 48V (DC) - Configurable Compatible battery types* Lead-acid (wet, gel, AGM) * Lithium-ion (Li-Ion) * Lithium iron phosphate (LiFePO4) DisplayBacklit LCD (background lighting) Measured values* Voltage (Volts) * Capacity (Percent %) * Graphical battery bar Accuracy± 1% (precision measurement) Power consumption< 5 - 10 mA (energy efficient) Protection functionsReverse polarity protection (protection against incorrect connection) Dimensions (L x W x H in mm)approx. 61 x 33 x 13 (standard mounting size)  FAQs about the battery tester 6V - 48VDo I need to set the device to measure 12V or 24V?No, high-quality testers in this segment feature an "auto-sensing" function. Simply connect the device; it detects the voltage range automatically and displays the corresponding result.Can I also use it to test lithium batteries?That depends on the specific model. Most simple testers are based on the voltage curves of lead-acid batteries. As lithium batteries (LiFePO4 or Li-Ion) have a flatter discharge curve, the percentage display may be inaccurate, but the pure voltage display is correct and usable.Does the tester put a heavy load on the battery?No, pure voltage and capacity testers mostly measure with high impedance and only draw a minimal current from the battery for display operation. They do not simulate a cold start current (like large load testers), but serve for quick status evaluation.Is the device waterproof?As a rule, these testers are splash-proof (e.g. for use under the bonnet), but not waterproof. They should not be left out in heavy rain or submerged in water.

This "Plug & Play Accell" smart adapter is the professional solution for connecting e-bike batteries from the Accell Group (e.g. used in Sparta, Batavus, Koga) to a universal battery tester. The proprietary battery systems from Accell, especially the ION technology and E-Motion systems, are known for their complex communication. This adapter performs the necessary signal translation, wakes up the battery management system (BMS), and thus enables reliable diagnostics and capacity measurement.Highlights at a glanceSpecific compatibility: Developed for Accell Group battery systems, often found in brands such as Sparta, Batavus and Koga (e.g. ION or E-Motion systems).Plug & Play: Easiest operation without complicated configuration – the adapter recognises the battery and automatically establishes the connection.BMS activation: Sends the necessary "wake-up" signal to the battery to release the discharge output, which is locked in idle mode.Professional diagnostics: Enables dealers to objectively assess state of health (SoH) data and remaining capacity, which is often difficult with the frequently integrated Accell batteries.Robust workshop quality: High-quality connectors and durable cable jackets ensure reliability in daily service use.Safe connection: Reverse-polarity-protected connectors prevent operating errors and protect both the battery and the test device.Precise analysis for Accell systemsAccell Group batteries (often known from the "banana batteries" integrated into the frame or specific pannier rack batteries) feature complex charging electronics. Without the correct handshake signal, these batteries do not supply power. This smart adapter simulates the e-bike's communication. Consequently, the BMS opens the circuit, and your battery tester can simulate a realistic load to determine the true range and health status of the battery.Indispensable for Dutch premium brandsAs Accell brands such as Sparta and Batavus are particularly widespread in the trekking and city sector (and especially in the Benelux and German markets), this adapter is a must for every e-bike workshop. It enables service on a huge fleet of existing bikes where standard measurement methods fail. Features ModelBatterytester Smart Adapter - Accell (Sparta / Batavus / Koga) ApplicationConnection cable for capacity test / diagnostics Compatibility (system)Accell ION drive systems (PMU 3 / PMU 4 generations) Frequent bike brandsSparta, Batavus, Koga, Hercules (some models), Ghost (E-Hybrids) Voltage range24V / 29V / 36V (depending on ION system, e.g. NiMH or Li-Ion) FunctionSimulation of the ION protocol to release the discharge output Connection (device)Specific connection for universal battery tester Connection (battery)ION system connector (often 3-pin or 4-pin XLR-like/round) Special featuresEnables testing on "closed" systems that would otherwise only work on the bike Weight (g)approx. 185  FAQs about the Smart Adapter for AccellDoes the adapter work for all Sparta/Batavus batteries?The Accell Group uses various systems (ION, E-Motion, Bosch). This adapter is specific to the proprietary Accell systems (often ION or their own rear hub motors). If the bike is equipped with a Bosch or Yamaha drive, you will need the appropriate Bosch or Yamaha adapter, even if "Batavus" appears on the frame.Can I measure the voltage with a multimeter?Not directly with most Accell batteries. The contacts are without voltage as long as there is no communication. The adapter is absolutely necessary to get the BMS to enable the voltage output.Does the battery need to be removed for testing?Yes, generally the battery is removed from the bike and connected directly to the adapter. This excludes possible faults in the bike's wiring and provides pure battery data.Is software required for evaluation?The adapter establishes the connection. The actual control of the discharge process and evaluation of the data (curve, capacity in Wh) takes place via the connected test device and its PC software.

The "Batterytester Plug & Play" is the professional and universal solution for diagnosing rechargeable batteries in workshops and service centres. Whether e-bike (pedelec), power tool, garden tool or mobile medical technology – this device enables manufacturer-independent checking of battery capacity and state of health (SoH). In combination with the powerful PC software and the matching smart adapters, you can perform fully automatic discharge tests and provide your customers with professional test reports.Highlights at a glanceUniversal compatibility: Tests all common battery technologies (Li-Ion, LiFePO4, Li-Po, NiMH, NiCd, lead-acid) in the voltage range from approx. 3V to 60V.Plug & Play system: Simple handling thanks to a modular concept – the base device is simply connected to the matching adapter (e.g. for Bosch, Yamaha, Panasonic).Professional logging: The included PC software automatically creates detailed service reports with discharge curve, capacity and rating.Realistic load simulation: Carries out real discharge tests under load to find weak points that remain hidden during pure voltage measurement.Future-proof: Thanks to interchangeable adapters and software updates, the system is equipped for future battery generations.High safety: Integrated protection against reverse polarity, overheating and short circuit ensures safe operation in the workshop.The centrepiece of modern battery diagnosticsUnlike simple multimeters which only measure voltage, the Batterytester Plug & Play performs a full cycle test. It discharges the battery in a controlled manner and measures precisely the energy (Wh) and charge (Ah) drawn. This is the only reliable way to determine if a used battery still has the required range for an e-bike or the required power for a tool.Modular and expandableThe strength of this system lies in its versatility. While you can use universal cables for standard batteries (open cable ends), specialised "Smart Adapters" are available for complex e-bike systems (such as Bosch, Yamaha, Brose, Shimano). These take care of communication with the battery management system (BMS) and make testing as easy as plugging in ("Plug & Play"). Features ModelBatterytester Plug & Play (Universal diagnostic system) ApplicationCapacity measurement & diagnosis for e-bike and tool batteries Voltage range6 V - 48 V nominal (measuring range 3 V - 60 V) Discharge current0.5 A - 10 A (adjustable, standard 5 A) Supported technologiesLi-Ion, Ni-MH, Ni-Cd, lead-acid (Pb) Measuring methodReal load test (simulation) with internal resistance measurement (Ri) OutputIntegrated thermal printer (instant printout) & PC interface (USB) Compatibility (adapter)Universal (clamps) + Smart Adapter for Bosch, Yamaha, Panasonic, Giant, Brose, and more Dimensions (L x W x H in mm)approx. 250 x 170 x 125 Weight (kg)approx. 2.6  FAQs about Batterytester Plug & PlayDo I need a special adapter for each battery?Not necessarily. For batteries with simple plus/minus contacts (without complex communication), the included universal cable is sufficient. For modern e-bike batteries (Bosch, Yamaha, etc.) that do not deliver current without communication, you will need the respective "Smart Adapter".Can the device also repair ("refresh") batteries?The device is primarily a diagnostic tool to determine the actual condition. With NiCd and NiMH batteries, a training effect can be achieved through repeated cycles (charging/discharging). However, defective lithium cells cannot be repaired, but the device helps you to identify them safely.Do I need a PC to use it?Yes, a PC or laptop (Windows) is necessary for the full range of functions. The software controls the test process, visualises the discharge curve in real time and generates the printable PDF test report for your customers.How long does a test take?This depends on the capacity of the battery and the selected discharge current. A complete capacity test (from 100% to 0%) usually takes several hours (approx. 2–4 hours), as this is the only way to measure the chemical capacity exactly. A quick test (internal resistance measurement) takes only a few seconds but is less meaningful regarding the range.

This "Plug & Play" adapter is the ideal connection solution for diagnosing 36V lead batteries (Pb), as commonly used in older e-bikes (e.g. with Antec drive), e-scooters or in the rehabilitation sector (electric wheelchairs). Equipped with the widely used 3-pin XLR connector, this adapter enables quick and safe connection to your battery tester without having to handle loose crocodile clips. It is specially designed for testing lead-acid, lead-gel and AGM batteries.Highlights at a glanceUniversal standard: Suitable for battery systems featuring the industry-standard 3-pin XLR charging port (commonly found in Antec, Tianneng or Phylion lead systems).Optimised for lead chemistry: Specially designed for 36V lead battery packs (Pb, Gel, AGM), for reliable under-load capacity testing.Plug & Play: Easy connection – the XLR connector plugs directly into the battery's charging socket, guaranteeing a secure contact for high currents.Safe connection: Avoids short-circuit hazards that can occur when using universal clamps on narrow XLR sockets.Robust build: High-quality cable cross-sections and sturdy connectors ensure durability for everyday workshop use.Versatile use: Ideal for maintenance of older pedelecs, e-scooters and mobility aids still based on proven lead technology.Precise analysis for 36V lead systemsMany older e-bikes (e.g. early discount store models with Antec technology) and current e-scooters utilise 36V lead batteries. Over time, these often lose capacity gradually or suffer from the "memory effect" (with incorrect maintenance) or sulphation. With this adapter you can connect the battery professionally to your test device to check whether the heavy battery pack still provides the necessary output or needs replacing.Standard connector XLR-3pThe 3-pin XLR connector is the de-facto standard for 24V and 36V lead chargers. As the pin assignment for lead batteries in this sector is highly standardised (usually Pin 1+ / Pin 2- or Pin 3-), this adapter provides huge time savings and added safety versus makeshift solutions. Features ModelBatterytester Plug & Play Adapter - Antec / XLR-3p (36V lead) ApplicationConnection cable for capacity test / diagnostics Compatibility (system)Antec drive systems & various e-bikes with 36V lead batteries Battery technologyLead-acid, lead-gel, lead-AGM (fleece) Nominal voltage36 V FunctionDirect discharge via the charging port Connection (device)Specific connection for universal battery tester Connection (battery)XLR 3-pin connector (standard pinout) NoteFor testing batteries whose charge port also allows discharge (standard for Antec/lead) Weight (g)approx. 175  FAQs about the Antec / XLR-3p adapterCan I use it to test lithium batteries with XLR connector?Technically, the adapter only provides the physical connection. If you have a 36V lithium battery which also uses an XLR port (and doesn't need special BMS communication), the adapter could fit. However, you must select the test device chemistry (Li-Ion instead of Pb) in your tester to get accurate results and avoid deep discharge.How is the XLR connector pinned?The adapter is configured to the most common 36V e-mobility standard (usually Pin 1 = Plus, Pin 2 or 3 = Minus). Because there are rare exceptions with deviant polarity, we recommend quickly checking the battery connector's polarity with a multimeter before first use, even though most testers have reverse polarity protection.Does the lead battery have to be 'woken up' for the test?No. Unlike modern lithium systems (like Bosch or Yamaha), lead batteries generally do not have a communicating BMS locking the output. There is always voltage. The adapter simply provides a safe mechanical connection. Electronic activation is not usually required in lead systems.Why is the test important for lead batteries?Lead batteries are heavy and age differently from lithium batteries. Merely testing voltage means little (voltage often drops instantly under load). Only a true capacity test with this adapter shows if the "full" battery collapses under load (sulphation) or is still usable.

This specialised Smart Adapter is the essential connector for professional battery diagnostic tools to test e-bike batteries from the Bosch Classic Line (36V). As Bosch batteries have a sophisticated battery management system (BMS), a simple direct tap is often not sufficient. This adapter establishes the correct physical and electronic connection between your battery tester and the Bosch Classic battery in order to make reliable statements about residual capacity, health (SoC/SoH) and performance.Highlights at a glanceSpecific compatibility: Exactly suitable for Bosch Classic Line batteries of the first generation (36V system).Plug & Play: Simple and reverse polarity protected connection thanks to original Bosch plug face.Smart communication: Enables the tester to communicate with the BMS or to enable the discharge output.Professional diagnosis: Essential for bicycle dealers and workshops to evaluate used Bosch systems or create service reports.Robust design: High-quality cables and connectors, designed for daily use in the service environment.Versatile: Suitable for rack and frame batteries of the Classic series (provided the connection is identical).Precise analysis for Bosch Classic batteriesThe Bosch Classic Line (Gen 1) is still widely used. In order to be able to test these batteries with a universal battery tester, this Smart Adapter is required. It not only bridges the mechanical connection, but also ensures the correct signal transmission so that the battery releases the discharge current. This allows you to carry out real capacity tests under load instead of just voltage measurements and provide your customers with well-founded test reports.Indispensable for e-bike serviceWhether you are trading in a used pedelec or troubleshooting on behalf of a customer, this adapter extends the functionality of your existing battery tester. It puts an end to DIY solutions and wobbly clamps and ensures a professional workflow in the workshop. Features ModelBatterytester Smart Adapter - Bosch Classic 36V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Bosch Classic Line (Generation 1, approx. 2010-2014) Compatible battery typesFrame batteries & rack batteries (36V versions) Nominal voltage36 V FunctionActivation of the BMS & release of the discharge current for the test Connection (device)Specific connection for universal battery tester Connection (battery)Original Bosch Classic plug (rectangular) Special featuresIntegrated electronics for simulating communication (bike detection) Weight (g)approx. 180  FAQs about the Smart Adapter for Bosch ClassicDoes the adapter also fit Bosch Active or Performance Line?No. The Bosch Classic Line uses a different connector and a different design than the newer Active (Gen 2) or Performance Line (Gen 3/4) batteries. For these newer systems you need the corresponding oval adapter.Can I charge the battery using this adapter?This adapter is primarily designed for connection to a diagnostic and test device (discharge/measurement). Whether charging is possible depends on the capabilities of the connected tester; as a rule, however, charging is carried out via the original Bosch charger.Does the adapter also work with 24V Classic batteries?The article designation specifies "36 V". Although the connectors are often mechanically similar, the pin assignment or coding differs between 36V and the rarer/older 24V systems. Please use the adapter only for the specified 36V system to avoid damage.Do I need software for this?The adapter itself is hardware. To analyse the data and control the test, you need the corresponding basic test device and its PC software. The adapter serves as an interface between the battery and the test device.n-bottom:16px;">This specialised Smart Adapter is the essential connector for professional battery diagnostic tools to test e-bike batteries from the Bosch Classic Line (36V). As Bosch batteries have a sophisticated battery management system (BMS), a simple direct tap is often not sufficient. This adapter establishes the correct physical and electronic connection between your battery tester and the Bosch Classic battery in order to make reliable statements about residual capacity, health (SoC/SoH) and performance. Highlights at a glanceSpecific compatibility: Exactly suitable for Bosch Classic Line batteries of the first generation (36V system).Plug & Play: Simple and reverse polarity protected connection thanks to original Bosch plug face.Smart communication: Enables the tester to communicate with the BMS or to enable the discharge output.Professional diagnosis: Essential for bicycle dealers and workshops to evaluate used Bosch systems or create service reports.Robust design: High-quality cables and connectors, designed for daily use in the service environment.Versatile: Suitable for rack and frame batteries of the Classic series (provided the connection is identical).Precise analysis for Bosch Classic batteriesThe Bosch Classic Line (Gen 1) is still widely used. In order to be able to test these batteries with a universal battery tester, this Smart Adapter is required. It not only bridges the mechanical connection, but also ensures the correct signal transmission so that the battery releases the discharge current. This allows you to carry out real capacity tests under load instead of just voltage measurements and provide your customers with well-founded test reports.Indispensable for e-bike serviceWhether you are trading in a used pedelec or troubleshooting on behalf of a customer, this adapter extends the functionality of your existing battery tester. It puts an end to DIY solutions and wobbly clamps and ensures a professional workflow in the workshop. Features ModelBatterytester Smart Adapter - Bosch Classic 36V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Bosch Classic Line (Generation 1, approx. 2010-2014) Compatible battery typesFrame batteries & rack batteries (36V versions) Nominal voltage36 V FunctionActivation of the BMS & release of the discharge current for the test Connection (device)Specific connection for universal battery tester Connection (battery)Original Bosch Classic plug (rectangular) Special featuresIntegrated electronics for simulating communication (bike detection) Weight (g)approx. 180  FAQs about the Smart Adapter for Bosch ClassicDoes the adapter also fit Bosch Active or Performance Line?No. The Bosch Classic Line uses a different connector and a different design than the newer Active (Gen 2) or Performance Line (Gen 3/4) batteries. For these newer systems you need the corresponding oval adapter.Can I charge the battery using this adapter?This adapter is primarily designed for connection to a diagnostic and test device (discharge/measurement). Whether charging is possible depends on the capabilities of the connected tester; as a rule, however, charging is carried out via the original Bosch charger.Does the adapter also work with 24V Classic batteries?The article designation specifies "36 V". Although the connectors are often mechanically similar, the pin assignment or coding differs between 36V and the rarer/older 24V systems. Please use the adapter only for the specified 36V system to avoid damage.Do I need software for this?The adapter itself is hardware. To analyse the data and control the test, you need the corresponding basic test device and its PC software. The adapter serves as an interface between the battery and the test device.

This specialised Smart Adapter is the link between your professional battery tester and e-bike batteries from the Panasonic Premium and Luxe systems. It supports both the 26V and 36V versions of this widespread drive generation (frequently installed in Flyer, KTM and Kalkhoff e-bikes). As these batteries have a battery management system that blocks the flow of current without the appropriate signal, this adapter enables the necessary communication to release the battery for precise capacity measurement.Highlights at a glanceDual compatibility: Suitable for Panasonic Premium, Luxe and DeLuxe battery systems in both 26V and 36V variants.BMS activation: Simulates the communication of the e-bike to "wake up" the battery and enable the discharge output for the test.Precisely fitting connection: Features the specific connector that fits mechanically and electrically exactly onto the contacts of the Panasonic Premium batteries.Professional diagnostics: Enables dealers and workshops to create reliable condition reports (SoH) for customer batteries.Robust workshop quality: High-quality cabling and strain-relieved connectors guarantee a long service life in daily service use.Easy application: Plug & Play – connect the adapter to the test device and the battery, the system recognises the connection.Precise analysis for Panasonic Premium batteriesThe Panasonic "Premium" and "Luxe" batteries (often recognisable by their design behind the seat tube or on the down tube) require a specific signal in order to deliver current. A simple multimeter or a direct load is often not sufficient. This Smart Adapter ensures that the battery management system (BMS) enables the output. Only in this way can your battery tester record a realistic discharge curve and determine the actual remaining capacity.Indispensable for Flyer and KTM ServiceAs Panasonic systems have been the market leader for premium e-bikes (especially Flyer C-series, T-series etc.) for years, these batteries are ubiquitous in routine service. With this adapter, you are able to make well-founded statements about the condition of used batteries, whether for resale or for processing complaints. Features ModelBatterytester Smart Adapter - Panasonic Premium / Luxe ApplicationConnection cable for capacity test / diagnostics Compatibility (system)Panasonic mid-motor systems (26V Premium & 36V Deluxe) Frequent bike brandsFlyer (C-, T-, L-, S-series), KTM, Kalkhoff, Raleigh, Kettler Voltage range26V (25.2V nominal) and 36V (automatic detection) FunctionActivation of the BMS & release of the discharge current for testing Connection (device)Specific connection for universal battery tester Connection (battery)Original Panasonic system connector Special featuresSimulates the communication of the pedelec to "wake up" the battery Weight (g)approx. 190  FAQs about the Smart Adapter for Panasonic PremiumHow can I recognise a Panasonic "Premium" battery?Panasonic Premium batteries often differ from the older "standard" systems (only 26V) by the display and the charge level indicator directly on the battery (push button with 5 LEDs) as well as the slightly wider design of the contact rail. This adapter is specially designed for this newer generation (Premium/Luxe).Does the adapter also work for the Panasonic mid-motor 36V "Next Generation"?No. The Panasonic "Next Generation" (often a downtube battery) uses a completely different connector system and communication protocol. For this type of battery, you need a different, specific adapter. This one is for previous drive generations (Premium/Luxe).Can I charge the battery via the adapter?The adapter is primarily intended to allow current flow from the battery into the test device (discharge/capacity test). Charging is usually most efficient via the original Panasonic charger, even though some testers could theoretically charge via the adapter (depending on the pin assignment of the tester).Why is there no current when I only connect clamps?Panasonic batteries for safety reasons switch off the output when they are not fitted to the bike. A resistance or data signal must be present to open the BMS. This is precisely the function that the Smart Adapter performs automatically.

This specialised Smart Adapter enables you to connect your professional battery tester to e-bike batteries of the "Panasonic Next Generation" (36V) system. This drive generation, often found in high-quality e-bikes from Flyer, KTM or Kettler (from around model year 2014), features a complex battery management system. The adapter not only establishes the physical connection but also handles the necessary communication ("handshake") to wake the battery from sleep mode and enable the discharge output for precise capacity measurement.Highlights at a glanceExact compatibility: Specially developed for the Panasonic "Next Generation" system (36V), which is mechanically and electronically different from the older premium/standard systems.BMS activation: Simulates the e-bike communication to prompt the battery management system (BMS) to release current for testing.Professional diagnostics: Allows bicycle dealers and service centres to create reliable test reports on remaining capacity and state of health (SoH).Robust construction: Equipped with high-quality connectors and durable cables for everyday use in the workshop environment.Secure connection: Reverse-polarity-proof connection guarantees flawless battery contact without loose contacts.Plug & Play: Easy handling – plug the adapter between the tester and battery, communication is automatic.Precise analysis for Next Generation batteriesBatteries of the "Next Generation" series (often designed as down tube or seat tube batteries) do not deliver voltage at the main contacts as long as they have not received the correct signal from the motor or display. A simple measurement with a multimeter is therefore impossible. This smart adapter overcomes this hurdle intelligently. It allows your battery tester to carry out a realistic load simulation to determine the actual range capacity of the customer's battery.Indispensable for modern e-bike serviceAs many premium manufacturers, such as Flyer, opted for the "Next Gen" system in the 2010s, there are a large number of these batteries in circulation. For the assessment of returned leased batteries, trade-ins or warranty issues, this adapter is the crucial tool for moving from mere estimates to measurable facts. Features ModelBatterytester Smart Adapter - Panasonic Next Generation ApplicationConnection cable for capacity test / diagnostics Compatibility (system)Panasonic Next Generation mid-motor systems (from approx. 2012/2013) Frequent bike brandsFlyer (Next Generation models), KTM, Kettler Rated voltage36 V FunctionActivation of the BMS & release of the discharge current (simulation of bus communication) Connection (device)Specific connection for universal battery tester Connection (battery)Original Panasonic Next Gen connector Special featuresEnables the testing of batteries that remain in "sleep mode" without communication Weight (g)approx. 200  FAQs about the Smart Adapter for Panasonic Next GenerationDoes this adapter also fit Panasonic Premium (26V/36V)?No. The "Premium" system (often the battery located behind the seat tube with a large handle) and the "Next Generation" system (often down tube or integrated) use completely different connectors and communication protocols. They are not compatible with each other. You need the Panasonic Premium Adapter for Premium batteries.Can I measure the voltage without the adapter?No. Panasonic Next Generation batteries switch off the output ("sleep mode") when they are not in the bike. Without the Smart Adapter, which sends the "wake-up signal", you will measure 0V at the contacts, even if the battery is fully charged.For which bicycle brands is the adapter relevant?The Panasonic Next Generation system was frequently installed in e-bikes from the brands Flyer (C-series, T-series of more recent date), KTM (certain models) and Kettler. If the battery is labelled "Next Generation", this is the correct adapter.Can I charge via the adapter?The adapter is primarily designed for diagnostic purposes (discharging/testing). Ideally, charging should always be carried out with the original charger to guarantee optimal cell balancing.

This specialised Smart Adapter is the crucial connection cable for the professional diagnosis of 36V e-bike batteries used in Brose drive systems (manufactured by BMZ). Equipped with the characteristic magnetic Rosenberger connector (RoPD), this adapter establishes a secure connection between your battery tester and the battery. It not only enables physical contact, but also provides the necessary signal transmission to enable the battery management system (BMS) for precise capacity measurement.Highlights at a glanceSpecific compatibility: Perfectly matched to 36V batteries from BMZ, which are used in Brose systems (e.g. in Rotwild, Bulls, Specialised models with BMZ battery).Rosenberger connector (RoPD): Features the magnetic, self-tightening Rosenberger connector for convenient and wear-free contacting.BMS activation: Wakes the battery from sleep mode and enables the discharge output, which is essential for testing modern smart batteries.Professional diagnostics: Indispensable for e-bike dealers and workshops to determine the state of health (SoH) and the real range of customer batteries.Robust quality: High-quality cables and connectors guarantee durability and reliability in daily workshop use.Plug & Play: Simple connection – the magnetic connector finds its position almost by itself, communication starts automatically.Precise analysis for BMZ batteries with Brose systemBatteries with Rosenberger connection have a sophisticated BMS and data lines (CAN bus or similar protocols). Without the correct "wake-up signal", the power contacts remain de-energised to prevent sparking on the magnetic connector. This smart adapter simulates the presence of the e-bike, activates the current flow and thus enables your test device to record realistic discharge curves and reliably identify defective cells or capacity losses.Standard in the modern e-bike workshopThe Rosenberger connector has established itself as the industry standard for high-quality e-bikes (especially mountain bikes and trekking bikes with Brose drive). In order to be able to professionally maintain and assess this growing fleet of vehicles – for example when returning leased bikes or selling used bikes – this adapter is a must for every well-stocked diagnostic station. Features ModelBatterytester Smart Adapter - Brose / BMZ (Rosenberger) ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Brose Drive Systems / BMZ Drive Systems Compatible battery typesBMZ batteries with Rosenberger charging socket (36V / 37V) Frequent bike brandsBulls (Brose models), Rotwild, Hercules, Scott (E-Silence) Rated voltage36 V FunctionWake up the BMS via data pin (wake-up signal) for the discharge test Connection (device)Specific connection for universal battery tester Connection (battery)Rosenberger connector (RoPD - magnetically coded) Weight (g)approx. 185  FAQs about the Smart Adapter for Brose / BMZDoes the adapter fit all batteries with Rosenberger connectors?The adapter is primarily designed for 36V BMZ batteries in the Brose system. Although the Rosenberger connector is also used in other systems (e.g. Green Mover / GoSwissDrive 36V), the allocation of the data pins may vary. In most cases, it works universally for 36V BMZ batteries, but if in doubt check the compatibility of your specific test device.Can I use it to test Specialised batteries?Although Specialised uses Brose motors and Rosenberger connectors, it often uses its own, highly specific battery firmware (Mission Control). Whether the adapter can "wake up" the battery depends strongly on the test device used. For standard BMZ batteries (e.g. in Bulls or Rotwild) it usually works perfectly.Why is the connector magnetic?The Rosenberger Power Data (RoPD) connector uses magnetic force to centre and fix itself in place. This prevents wear from mechanical plugging and twisting and safely releases if you trip over the cable, without damaging the socket.Can I measure the battery directly without an adapter?No. The Rosenberger connector is constructed so that it is not live as long as no connection exists. This prevents short circuits caused by metallic objects sticking to the magnet. The adapter is absolutely necessary to activate the contacts.

This specialised Smart Adapter is the essential connector for the professional diagnosis of e-bike batteries from the Yamaha PW series (36V). As Yamaha batteries have an intelligent management system that blocks the current output without communication with the drive unit, this adapter is necessary to "wake up" the battery for testing purposes. It establishes the physical and electronic connection between your battery tester and the battery and thus enables precise statements to be made about capacity and state of health (SoH).Highlights at a glanceSpecific compatibility: Developed for all 36V batteries of the Yamaha PW system (incl. PW-X, PW-SE, PW-ST, PW-TE), for both frame and rack batteries.BMS activation: Simulates drive unit communication to trigger the battery management system (BMS) to enable the discharge output.Precise connection: Features the specific Yamaha system connector, which ensures safe and polarity reversal-free contacting of the battery terminals.Professional diagnosis: Enables dealers and workshops to create reliable test reports and objectively assess complaints or used bikes.Robust workshop quality: High-quality materials and strain relief ensure longevity in daily service use.Simple handling: Plug & Play – connect the adapter, the tester recognises the battery and starts communication automatically.Precise analysis for Yamaha PW batteriesYamaha e-bike batteries are designed so that, for safety reasons, they have no voltage on the main contacts when they are not mounted in the bike and switched on. A simple measurement with a multimeter therefore often shows 0V. This Smart Adapter overcomes this obstacle by sending the necessary control signals. This closes the main relay in the battery and your test device can record a realistic discharge curve under load.Standard for Haibike, Winora and Co.The Yamaha PW system is one of the most widely used drive systems in the e-MTB and trekking sector (installed on Haibike, Winora, Raymon, Lapierre, among others). For workshops servicing these brands, this adapter is indispensable for carrying out efficient fault diagnoses and reliably determining the condition of leasing returns. Features ModelBatterytester Smart Adapter - Yamaha PW System ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Yamaha PW, PW-X, PW-SE, PW-TE drive systems Frequent bike brandsHaibike (SDURO), Winora, Lapierre, Ghost, Batavus Nominal voltage36 V FunctionActivation of the BMS (wake-up) via signal pin to enable the output Connection (device)Specific connection for universal battery tester Connection (battery)Original Yamaha 4-pin plug (large charging plug) Special featuresNot compatible with older Yamaha 26V systems Weight (g)approx. 195  FAQs about the Smart Adapter for Yamaha PWCan I measure the battery with a multimeter without an adapter?No. Yamaha PW batteries switch off their main contacts ("sleep mode") as soon as they are disconnected from the bike. Without the adapter, which signals to the battery "I am an e-bike", you will not be able to measure any voltage at the contacts, even if the battery is fully charged.Does the adapter fit the old 26V Yamaha batteries?No. The older Yamaha 26V systems (often known as Yamaha PAS) use a different connector shape and technology. This adapter is specifically designed for the newer 36V PW generation (from approx. 2014).Does the adapter also work with Intube batteries?Yamaha Intube batteries (integrated in the frame) often use the same electrical connection as the external frame batteries. If the connector fits mechanically, the adapter will also work. Compatibility should be checked for some third-party batteries (e.g. Simplo for Yamaha).Can I charge via the adapter?The adapter is primarily designed for the discharging process (diagnosis). Yamaha batteries should always be charged using the original Yamaha charger, as this also controls temperature monitoring and balancing during charging.

This specialised Smart Adapter is the indispensable interface for the diagnosis of Panasonic SIB (Smart Integrated Battery) batteries. These 36V high-performance batteries were developed exclusively for premium e-bikes, in particular for the Swiss brand Flyer (e.g. U series with multispeed motor). As SIB batteries have complex communication (often integrated in the FIT system), they do not emit any voltage when removed. This adapter simulates the vehicle electronics, wakes up the battery management system (BMS) and thus enables a professional capacity test.Highlights at a glanceSpecific compatibility: Customised for Panasonic SIB (Smart Integrated Battery) 36V systems, primarily found in Flyer e-bikes.BMS activation: Adopts the digital "handshake" to wake the battery from safety sleep mode and enable the main contacts for testing.Exclusively for Flyer: Supports the diagnosis of batteries that are installed in combination with the Panasonic Multispeed (2-speed) engine or the FIT system.Precise connection: Features the special SIB system connector, which guarantees a mechanically secure and reverse polarity protected connection.Professional diagnosis: Enables dealers to generate valid service reports on the state of health (SoH) of these high-priced batteries.Plug & Play: Easy to use – insert the adapter between tester and battery, communication starts automatically.Precise analysis for SIB batteries (Smart Integrated Battery)The Panasonic SIB batteries are characterised by their integration into the frame and their high energy density. They are "intelligent" and communicate permanently with the display and motor. Without the appropriate wake-up signal, the terminals remain de-energised. This smart adapter is the only tool that makes it possible to discharge and test these batteries outside the bike under realistic conditions in order to reliably identify ageing or defects.Standard for Flyer dealersAs Flyer was one of the main customers for this special Panasonic technology (especially for the innovative models with integrated battery and 2-speed motor), this adapter is essential for every workshop that services Flyer bikes. It allows the safe evaluation of lease returns and trade-ins. Features ModelBatterytester Smart Adapter - Panasonic SIB (Flyer) ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Panasonic Multispeed Assist System / Flyer FIT 1.0 (Flyer Intelligent Technology) Compatible battery typesPanasonic SIB (Smart Integrated Battery) batteries (e.g. STB-630, STB-750) Frequent bike brandsFlyer (U-Series, Upstreet, Uproc - models with SIB battery) Nominal voltage36 V / 43.2 V (system-dependent, adapter covers SIB series) FunctionActivation of the BMS (wake-up) to enable the discharge output Connection (device)Specific connection for universal battery tester Connection (battery)Panasonic SIB system connector (multipin blade) Weight (g)approx. 200  FAQs about the Smart Adapter Panasonic SIBIs this adapter identical to the "Panasonic Next Generation" adapter?No. Panasonic has different systems. "Next Generation" (often down tube battery, but not fully integrated) and "SIB" (Smart Integrated Battery, fully integrated) use different housings and connectors. This adapter (AT00098) is specially designed for the SIB-Series.Can I also use it to charge the battery?The adapter is primarily designed for connection to the test device for discharging (diagnosis). Charging should always be carried out with the original Panasonic/Flyer charger in order to correctly operate the complex protective circuits of the SIB battery.Can I measure the voltage with a multimeter?No. Like almost all modern Panasonic batteries, the SIB switches to "deep sleep" as soon as it leaves the wheel. There is 0V at the contacts. No measurement is possible without the Smart Adapter, which simulates communication.For which Flyer models does it fit?It is typically designed for Flyer models that use the Panasonic Multi Speed Assist motor (2-speed) and the integrated battery (e.g. Flyer U series). If in doubt, please compare the plug shape of your battery.

This Smart Adapter is the specialised connection solution for diagnosing e-bike batteries of the classic Panasonic mid-motor drive (26V standard system). This legendary drive system, which played a key role in kickstarting the e-bike boom (known from Flyer C series, Kalkhoff, Raleigh), is represented millions of times on the market. The adapter establishes a safe and polarity reversal-free connection between your battery tester and the battery to perform a reliable capacity test, which is crucial for the service assessment of batteries that are often getting older.Highlights at a glanceSpecific compatibility: Designed for the classic Panasonic 26V standard system (recognisable by the wide carrying handle and the position behind the seat tube).Safe contacting: Features the precisely fitting receptacle plug for the blade contacts of the Panasonic battery, which prevents loose contacts and sparking.Plug & Play: Very easy handling – connect the adapter and the test device can immediately begin diagnosis.Professional diagnosis: Enables dealers to objectively determine the remaining capacity (SoH) in order to decide whether a cell replacement or new purchase is necessary.Robust workshop quality: Durable materials and sturdy connectors are designed for daily use in the bike workshop.Wide market coverage: Covers a huge fleet of older e-bikes (Flyer, KTM, Kalkhoff, Raleigh, Victoria) that now increasingly require service.Precise analysis for the classicThe Panasonic 26V drive is considered the “forefather” of modern pedelecs. Even though the technology is considered robust, the lithium-ion cells (often Mn-based) are subject to natural ageing. With this adapter you can perform a real discharge under load instead of just estimating the voltage. This way you can identify batteries that indicate “full”, but immediately break down when climbing hills (high internal resistance).Indispensable for servicing existing bikesAs these e-bikes are often very durable, they are still found on the roads in large numbers. For workshops, the ability to professionally test these older systems is an important service building block to ensure customer retention and avoid costly misdiagnoses. Features ModelBatterytester Adapter - Panasonic Standard 26V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Panasonic mid-motor systems (standard 26V generation) Frequent bicycle brandsFlyer (C-, T-series old), Kalkhoff, Raleigh, Rixe, KTM (older models) Nominal voltage26 V (25.2 V nominal) FunctionDirect connection to the discharge port of the battery Connection (device)Specific connection for universal battery tester Connection (battery)Original Panasonic standard plug (white/black, rectangular) Special featuresFor the first generation of Panasonic batteries (often NiMH or early Li-Ion) Weight (g)approx. 180  FAQs about the Smart Adapter for Panasonic (Standard)What is the difference to the “Premium” Adapter?The Panasonic system has been further developed. The older Standard system (26V) has a different contact geometry and communication than the newer Premium system (26V & 36V, often recognisable by the “Push” button for charge status display on the battery). The adapters are not mechanically compatible. This adapter is for the older standard version.Can I also measure the voltage with a multimeter?Yes, in the Panasonic 26V standard system, voltage is often present directly at the outer contacts (unlike Bosch). However, the open-circuit voltage says nothing about the condition under load. Only the adapter in combination with the load tester provides a meaningful capacity curve.Which brands does the adapter fit?It fits almost all e-bikes with the Panasonic 26V mid-motor that was the market standard until around 2012/2013. These include models from Flyer (F-, C-, T-, L-series), Kalkhoff (Agattu, Tasman), Raleigh (Dover), KTM (Amparo), Victoria and many more.Can I charge via the adapter?The adapter is designed for connection to the diagnostic device (discharge). The original Panasonic charging station (tabletop charger) should always be used for charging.

This specialised Smart Adapter is the key tool for professional diagnosis of e-bike batteries of the Impulse drive system. The Impulse system developed by Derby Cycle (installed in brands such as Kalkhoff, Raleigh, Rixe, Gazelle) is one of the best-selling drive systems in German-speaking countries. As Impulse batteries are equipped with intelligent battery management and the contacts are de-energised when removed, this adapter is necessary to activate the battery for test purposes and to carry out a precise capacity measurement.Highlights at a glanceSpecific compatibility: Customised for 36V batteries of the Impulse system (Impulse 1.0, 2.0 and often Impulse Evo), which are installed millions of times in Kalkhoff and Raleigh e-bikes.BMS activation: Simulates the bike's communication to wake the battery from "deep sleep" and activate the main contacts for the discharge test.Precise connection: Features the specific Impulse system connector (often curved or magnetic, depending on the version), ensuring safe contact.Professional diagnosis: Enables dealers to create valid test protocols (SoH) for leasing returns, warranty claims, and the used bike trade.Plug & Play: Easiest operation without manual settings – connect the adapter, and the tester recognises the battery automatically.Robust workshop quality: High-quality cables and durable connectors guarantee reliability in daily service use.Precise analysis for Derby Cycle batteriesImpulse batteries (often known as seat tube batteries with large range) are highly complex. To prevent sparking and corrosion, the external contacts carry 0 volts as long as there is no communication with the motor. This Smart Adapter intelligently bridges this safety function. It sends the necessary start signal, allowing your battery tester to simulate a realistic load and determine the actual remaining capacity in watt-hours (Wh).Standard for Kalkhoff and Raleigh serviceDue to the enormous prevalence of Impulse drives in Germany and Europe, this adapter is a "must-have" for every e-bike workshop. It enables diagnosis for a huge fleet of existing bikes, where ageing effects now need to be checked. Features ModelBatterytester Smart Adapter - Impulse 1.0 / 2.0 / Evo ApplicationConnection cable for capacity test / diagnosis Compatibility (System)Impulse 1.0, Impulse 2.0, Impulse Evo & Evo RS (Derby Cycle) Frequent bike brandsKalkhoff, Raleigh, Focus, Univega, Gazelle, Rixe Supported battery typesSeat tube batteries & down tube batteries (various capacities 11Ah - 17Ah) Nominal voltage36 V FunctionActivation of the BMS (wake-up) via system pins to enable the output Connection (device)Specific connection for universal battery tester Connection (battery)Original Impulse system connector (usually 5-pin / blade contact) Weight (g)approx. 190  FAQs about the Smart Adapter for ImpulseWhich brands does the adapter fit?The Impulse drive is a product of Derby Cycle. The adapter therefore primarily fits e-bikes of the brands Kalkhoff, Raleigh, Rixe, Univega, Gazelle (models with Impulse motor) and Focus (models with Impulse motor).Can I test Impulse Evo batteries with it?The Impulse system has developed various connector types. The classic Impulse 1 & 2 batteries (seat tube) use a bent plug contact. Impulse Evo often uses a magnetic Rosenberger connector. Please check whether the adapter connector is mechanically compatible with your battery. There are often combination adapters or specific cables for Evo.Can I measure the voltage without an adapter?No. Impulse batteries completely switch off the output when not installed in the bike. A multimeter shows 0V. Without the Smart Adapter that activates the system, diagnosis is not possible.Is the adapter also for the old 26V Panasonic batteries in Kalkhoff bikes?No. Kalkhoff previously installed Panasonic drives (26V) before the Impulse system (36V) was introduced. For the old Panasonic batteries, you require the "Smart Adapter for Panasonic Standard". This adapter here is only for the newer Impulse system.

This Smart Adapter is the professional interface to connect your battery tester to the widely used Bosch e-bike batteries of the Active and Performance Line (36V). As modern Bosch batteries (Gen 2, 3 and 4) have a complex battery management system, they do not emit any voltage at the contacts without a specific communication signal. This adapter simulates the electronics of the e-bike, wakes the battery from "sleep mode" and thus enables precise diagnostics, capacity measurement and condition assessment (SoH).Highlights at a glanceWide compatibility: Supports all Bosch 36V batteries with the standard oval connector, including Active Line, Performance Line, Performance CX and Cargo Line (Generation 2, 3 and 4).BMS activation: Takes over the necessary digital "handshake" with the battery to trigger the battery management system (BMS) to release the discharge current.Precise connection: Features the original oval Bosch system connector for a mechanically safe and polarity reversal-free connection to frame, rack and PowerTube batteries.Professional diagnosis: Enables dealers and workshops to create valid test reports for leasing returns, warranty claims or used bike sales.Robust workshop quality: High-quality cables and strain-relieved connectors guarantee reliability in daily, intensive service use.Plug & Play: Easy to use without manual configuration – connect the adapter, and communication starts automatically.Precise analysis for the Bosch E-Bike System 2 (BES2)Bosch batteries are the market standard in the e-bike sector. The Smart Adapter is essential for maintaining them safely. It bypasses the battery's safety cut-out, which normally prevents voltage from being applied when the battery is not in the bike. With this adapter, your test device can simulate a realistic riding load and thus detect weak points in the cell pack that a simple voltage measurement would overlook.Ideal for PowerPack and PowerTubeRegardless of whether it's the classic "PowerPack" (add-on battery) or the integrated "PowerTube" – as long as the battery has the oval connection of generations 2, 3 or 4, this adapter is the right tool. It is a must for every certified e-bike workshop. Features ModelBatterytester Smart Adapter - Bosch Active / Performance 36V ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Bosch Active Line, Performance Line, Performance CX (Gen 2, 3, 4) Compatible battery typesPowerPack (frame & rack) & PowerTube (Intube) Nominal voltage36 V FunctionActivation of the BMS & release of the discharge current (simulation of CAN bus communication) Connection (device)Specific connection for universal battery tester Connection (battery)Original Bosch Oval connector (for Active / Performance) Special featuresEnables testing of batteries that would switch off without bike communication Weight (g)approx. 200  FAQs about the Smart Adapter for BoschDoes the adapter also fit the new "Smart System" (BES3)?It depends on the version of your adapter. The standard adapter with the oval connector described here does not physically fit the new BES3 batteries (Smart System from approx. 2022), as these use a different connector geometry and communication. A separate, specific adapter is required for the BES3 system.Can I use it to test Bosch Classic (Gen 1) batteries?No. The Bosch Classic Line (Gen 1) uses a rectangular connector and a different connection technology. For these older batteries you need the "Smart Adapter for Bosch Classic". This adapter here is for the successors (Gen 2 and newer) with an oval connector.Can I test the battery with a multimeter without an adapter?No, this is not possible. Bosch batteries de-energise the main contacts ("deep sleep") as soon as they are removed from the bike. A multimeter will show 0V. Only the adapter that sends the control signal can unlock the voltage.Does the adapter also support 48V or 24V systems?No. The Bosch Active/Performance system works almost exclusively with 36V. The adapter is specifically designed for this voltage range and the Bosch protocol.

This high-quality E-Bike Vision quick charger is the most powerful solution for extremely fast and safe charging of all 36V E-Bike Vision PowerPack (POP) batteries. With a very high charging current of 6 amperes (6A), it charges your battery significantly faster than conventional chargers, thus minimising the waiting time until your next ride. The robust and compact design makes it the perfect charger for demanding e-bikers who want maximum performance and efficiency.Highlights at a GlanceExtremely fast charging: With 6 amperes charging current, your e-bike battery is charged efficiently in no time at all.Universal compatibility: Suitable for all 36V E-Bike Vision PowerPack (POP) batteries.Intelligent charging electronics: Permanently monitors the charging process and automatically switches off after full charge to protect the battery.High safety: Comprehensive protection against short circuit, overheating and overvoltage.Compact and robust: Lightweight and durable housing, ideal for everyday use and when on the go.Less Waiting, More RidingReduce the charging time to a minimum and maximise your time on the bike. With a charging current of 6 amperes, this quick charger is one of the most powerful on the market. An empty battery with 18Ah capacity is, for example, fully ready for use again in just about 3 hours. The LED display provides clear and distinct information about the current charging status at all times.Safe and Gentle for Your BatteryDespite the extremely high charging speed, the safety and longevity of your valuable battery come first. The intelligent charging electronics optimally adapt the charging process to the condition of the battery. After reaching full capacity, the device automatically switches to maintenance mode to prevent overcharging and to maximise the lifespan of the battery cells.Flexibility for Different SystemsThis charger is the heart of the flexible E-Bike Vision charging system. While it is directly compatible with the E-Bike Vision batteries for Panasonic 36V and Bosch Classic Line, it can also be used, via separately available charging adapters, to charge original batteries of the Yamaha, Bosch (Active/Performance) and Panasonic (Next Generation) systems. Features  ModelE-Bike Vision Quick Charger 36V 6A ApplicationCharger for 36V E-Bike batteries Input voltage100 - 240V AC Output voltage (V)42.0 Charging current (A)6 Connection (battery)System-specific charging adapter required DisplayLED status display Dimensions (L x W x H in mm)approx. 200 x 95 x 50 Weight (g)approx. 850  FAQs about the E-Bike Vision Quick ChargerWhat does 6A charging current mean and how does it affect the charging time?The "6A" stands for 6 amperes of charging current. This is the "speed" at which the battery is charged. A 6A charger charges a battery three times faster than a 2A standard charger and still 50% faster than a 4A charger. The exact charging time is calculated from the capacity of the battery (in Ah) divided by the charging current (in A), for example: 18 Ah / 6 A = 3 hours.Can I also use this charger to charge my original battery (e.g. from Yamaha)?Yes, that is possible. However, you will need the appropriate, separately available charging adapter for your specific battery system (e.g. Yamaha PW-series). The adapter provides the correct mechanical and electrical connection to the charging socket of your original battery.Is extremely fast charging harmful for my battery?Modern lithium-ion batteries and their battery management systems (BMS) are designed for quick charging with currents like 6A. The intelligent electronics in charger and battery ensure that the charging process takes place safely and in the optimum range so that the lifetime of the cells is not negatively affected.Can I leave the battery on the charger overnight?Yes, that's safe. The intelligent charger detects when the battery is fully charged and automatically ends the main charging process. It then switches to a maintenance mode with very low current to keep the battery full without overcharging.

The Beltrona 12V/3A desktop charger is a compact and extremely reliable solution for regular and gentle charging of 12-volt lead-acid batteries. It perfectly bridges the gap between weak trickle chargers and large, unwieldy workshop equipment. With a constant charging current of 3 amps (3000 mA), it quickly restores discharged batteries to full power without thermally stressing the cell chemistry with excessive currents.Equipped with robust, colour-coded crocodile clips, the charger can be connected to almost any standard battery terminal in no time at all. Thanks to the intelligent, microprocessor-controlled charging electronics, the device works fully automatically. As soon as the final charging voltage is reached, it switches to trickle charging and thus effectively protects the battery from harmful overcharging.Highlights at a glanceUniversal compatibility: Perfectly suited for all common 12V lead-acid types (wet batteries, maintenance-free AGM, VRLA and gel batteries).Fast charging process: Provides a powerful 3 ampere charging current for fast and battery-friendly recharging.Flexible crocodile clips: Enables fast, safe and universal connection to a wide range of battery terminals.Comprehensive safety: Integrated protection mechanisms against short circuit, reverse polarity (incorrectly connected terminals) and overload.Fully automatic: Automatic switchover to trickle charging after a full charge to maximise battery life.Compact design: The lightweight plastic desktop housing fits anywhere and is easy to store or transport.Areas of applicationThe Beltrona 12V/3A charger is the ideal all-rounder for workshops, garages and hobby rooms:Two-wheelers & motor vehicles: Ideal for charging motorbike, scooter, quad bike or smaller car batteries.Garden & Leisure: Ensures full batteries for ride-on mowers, boats, golf caddies or electric fencing devices.Safety technology: For the maintenance and occasional recharging of 12V buffer batteries in alarm systems or small UPS systems.Hobby & modelling: Reliable power supply for charging 12V lead-acid batteries in feed boats or large modelling vehicles.Assembly & safety instructionsCorrect connection sequence: For safety reasons, always connect the red terminal to the positive pole (+) and the black terminal to the negative pole (-) of the battery first. Only then insert the mains plug into the socket.Good ventilation: Gases can be produced when charging open lead-acid batteries. Always charge batteries in well-ventilated rooms and avoid flying sparks in the immediate vicinity.Dry environment: The charger is designed for use in dry indoor areas (workshop, cellar, garage). Be sure to protect the housing from rain and direct moisture.Safe disconnection: When charging is complete, first disconnect the mains plug from the socket. Only then remove the crocodile clips from the battery terminals. Features ModelBeltrona 12V-3A desktop charger Supported battery types**Lead-acid, AGM, gel, VRLA** Nominal output voltage**12 V** Max. Charging current**3.0 A** Recommended battery capacity**10 Ah to 60 Ah** Charging method3-stage (IUoU) Input voltage100 - 240 V AC, 50/60 Hz Connection output**Crocodile clips** (red/black) DisplayStatus LED (charging / full) SafetyShort-circuit, overload and reverse polarity protection FAQs about the Beltrona desktop charger 12V/3AFor which battery sizes (Ah) is this charging current optimal?Best for capacities from approx. 10 Ah to 30 Ah. With 3 amps, you can charge these medium-sized batteries (e.g. from a ride-on mower or motorbike) quickly and gently. You can theoretically also connect larger car batteries (e.g. 60 Ah), but a full charge will then take longer (roughly approx. 20 hours).Can I use it to charge lithium batteries (Li-Ion or LiFePO4)?No, this is not recommended. The voltage curve of this charger is specially tailored to the cell chemistry of lead batteries. Lithium batteries require different charging characteristics and often require communication with the battery management system (BMS). Using a pure lead-acid charger can damage lithium cells.Will the device overcharge my battery if I leave it connected for days?No, the device works fully automatically. As soon as the charger recognises that the battery is fully charged, it automatically switches to trickle charging. Only very small currents then flow, which merely compensate for the natural self-discharge of the battery.

This Ansmann microcontroller fast charger is the universal all-in-one solution for modelling and tool batteries. Designed for NiMH and NiCd battery packs consisting of 1 to 10 cells (nominal voltage 1.2V to 12.0V), the device recognises the number of cells fully automatically and controls the charging process precisely. Thanks to state-of-the-art microcontroller technology with -dU cut-off, your batteries are not only charged quickly, but also safely and with optimised service life.Highlights at a glanceUniversal compatibility: Charges NiMH and NiCd battery packs with 1 to 10 cells (1.2V - 12.0V) fully automatically.Intelligent microcontroller control: The -dU (minus-delta-U) cut-off reliably recognises when the battery is fully charged and ends the fast charging process to prevent overcharging.Versatile connections: Often equipped with a Tamiya plug and additional adapters (e.g. crocodile clips or hollow plugs) to connect a wide variety of packs.Safety timer: An integrated safety timer serves as an additional protective mechanism to terminate the charging process in the event of defective batteries.Can be used worldwide: Thanks to the wide-range input (100-240V AC), the charger can be used internationally.Discharge function (depending on model): Many models in this series offer a button or function for discharging the battery before charging in order to minimise the memory effect (with NiCd) or lazy battery effect (with NiMH).Precise charging technology for battery packsThe centrepiece of this charger is the microcontroller. It monitors the voltage curve during the charging process. As soon as the battery has reached its maximum capacity, the voltage drops slightly (-dU effect). The device registers this immediately and switches from fast charging to impulse trickle charge. This guarantees that your battery pack is always brim-full and ready for use without getting hot.Ideal for modelling and hobbiesWhether for remote-controlled cars (RC cars), airsoft weapons, racing packs or self-assembled battery packs in torches and tools – this charger is the perfect companion. The automatic setting to the battery voltage makes manual switching superfluous and avoids operating errors. Features ModelAnsmann ACS 110 Traveller ApplicationCharger for battery packs in modelling, lamps, toys Compatibility (cells)1 to 10 cells (automatic detection) Battery technologyNickel-metal hydride (NiMH) & nickel-cadmium (NiCd) Output voltage1.2 V - 12.0 V Charging current800 mA Capacity rangeRecommended for 800 mAh to 10,000 mAh Charging methodMicrocontroller-controlled (-Delta U cut-off, impulse trickle charge) Special features* Pre-discharge function (Discharge) * Usable worldwide (100-240V AC) * Safety timer & short-circuit protection Scope of delivery (plug)8-piece secondary plug set (hollow plug, jack), Tamiya plug, crocodile clips Weight (g)approx. 340 (set)  FAQs on the Ansmann microcontroller fast chargerCan I also use it to charge Li-Po or Li-Ion batteries?No, this device is designed exclusively for nickel-metal hydride (NiMH) and nickel-cadmium (NiCd) rechargeable batteries. Lithium batteries have completely different charging characteristics and must not be connected under any circumstances (fire hazard).How do I connect my battery?The device is usually supplied with a standard Tamiya plug (white, 2-pin), which is very common in modelling. An adapter set is often included (e.g. crocodile clips for open cable ends or jack plugs). Always ensure that the polarity is correct (red to plus, black to minus).Do I have to set the voltage?No, that's the big advantage of this charger. You simply connect the pack. The microcontroller automatically recognises the voltage level of the pack and adjusts the charging process accordingly, regardless of whether it is a small 2-cell pack or a large 10-cell pack.What do the LEDs mean?Typically: Red (steady light): The battery is charged quickly. Yellow (if available): The battery is discharged (discharge function active). Green: The battery is full and is trickle charged. Flashing: Error or polarity reversed (please observe operating instructions). 

This specialised Smart Adapter is the professional interface for diagnosing high-performance batteries of the Shimano Steps E-MTB series (E8000, E7000 and EP8). In contrast to the older E6000 series, these modern E-mountain bike systems use different connection technology and communication. As Shimano batteries completely shut down when removed for safety (deep sleep), this adapter is absolutely essential. It simulates the presence of the drive unit, wakes up the battery management system (BMS) and activates the main contacts for precise capacity measurement.Highlights at a GlanceSpecific compatibility: Developed for the Shimano Steps Performance Line (E8000, E7000) and the EP8 series (EP800/EP801), suitable for external and Intube batteries.BMS activation: Takes over the digital "handshake" to wake the battery from sleep mode and release the voltage at the contacts.Precise connection: Features the specific connector for the Shimano E-MTB battery generation (e.g. for BT-E8010, BT-E8020, BT-E8035).Professional diagnostics: Enables dealers to create valid service reports on the state of health (SoH) of high-quality E-mountain bikes.Robust workshop quality: High-quality cables and durable connectors guarantee reliability in tough workshop use.Plug & Play: Easiest handling without software configuration on the adapter – connect and the test device starts communication.Precise Analysis for Shimano E-MTB PowerThe batteries of the E8000 and EP8 series are designed for heavy off-road loads. To reliably assess their condition – for example with leasing returns or the sale of used E-MTBs – a multimeter is not enough, as the contacts are de-energised. This Smart Adapter allows your battery tester to simulate a realistic riding load. This way you can reliably detect whether the battery is still delivering full power for steep climbs or whether the internal resistance has increased with age.Standard for Performance WorkshopsShimano drives are installed in countless high-end E-MTBs (e.g. from Commencal, Husqvarna, Merida, Santa Cruz). This adapter is the crucial tool for professional maintenance of these bikes and to provide customers with reliable information about their range. Features ModelBatterytester Smart Adapter - Shimano Steps E8000 / EP8 ApplicationConnection cable for capacity test / diagnosis Compatibility (system)Shimano Steps E8000, EP8 (EP800/EP801), E7000, E6100, E5000 Compatible battery typesBT-E8010, BT-E8020, BT-E8035, BT-E8036 (frame, Intube & integrated) Nominal voltage36 V FunctionBMS activation (Wake-Up) for enabling the discharge output Connection (device)Specific connection for universal battery tester Connection (battery)Shimano Steps specific adapter plug (often in conjunction with SM-BTE adapter) Special featuresAlso supports the newer battery generations of the EP8 series Weight (g)approx. 210  FAQs about the Smart Adapter for Shimano E8000 / EP8Is this adapter identical to the one for Shimano E6000?No. The older E6000 system (City/Trekking) uses different connectors than the more powerful E8000/EP8 systems. Although both have 36V, the connector does not fit mechanically. Please check the model number of your battery (BT-E...).Can I measure the voltage without an adapter?No. Shimano batteries have a strict safety shutoff. If they are not communicating with the motor, there are 0 volts at the contacts. The Smart Adapter is the only way to bypass this lockout for diagnostics.Can I charge via the adapter?The adapter is primarily designed for connection to the diagnostic device (discharging). Charging should always be done with the original Shimano charger (e.g. EC-E6002 or EC-E8004) to ensure cell balancing.Does it also work with third-party batteries for Shimano?Many third-party manufacturers (e.g. Simplo or Darfon) that build batteries for Shimano systems use the same communication protocol and the same connector. In these cases, the adapter usually works without any problems.

The Beltrona lead-acid battery charger 24V 8A offers an efficient and reliable solution for charging 24V lead-acid batteries. With a strong output power of 8 amps, this charger enables fast yet gentle charging that optimally supplies your batteries and extends their service life. It is compatible with various types of lead-acid, gel and AGM batteries, making it ideal for use in wheelchairs, electric vehicles, solar systems and emergency power systems. The charger is equipped with important protective functions such as overcharge protection, short-circuit protection and reverse polarity protection to ensure maximum safety. Thanks to its robust design and user-friendly operation, this charger is ideal for both professional applications and private use.