Special cells
Varta Lithium photobattery CRP2 6V (single blister)
The VARTA CRP2 is a high-performance 6-volt lithium primary battery developed specifically for devices with high, short-term power requirements such as cameras and flash units. Based on lithium manganese dioxide technology (Li-MnO2), it offers exceptionally high performance, extremely low self-discharge and a very wide operating temperature range. Delivered in a protective single blister, it is the ideal power source for demanding photography and other high-tech applications.Highlights at a glanceHigh performance: Developed for high-tech devices with high and fast power requirements (high drain).Quick flash readiness: Delivers high currents quickly for rapid charging of photo flashes.Extreme longevity: Can be stored for up to 10 years thanks to extremely low self-discharge.Wide temperature range: Reliable performance under extreme conditions from -20 °C to +70 °C.Safe packaging: The protective blister guarantees freshness and performance until use.Reliable power for photography and high-tech devicesThe VARTA CRP2 is the preferred power source for a wide range of devices that require high performance and absolute reliability. Its main field of use is in analogue and digital photography, supplying SLR cameras and external flash units. It is also ideal for use in high-intensity LED torches, smart home sensors and security technology.Superior lithium manganese dioxide technologyLithium manganese dioxide technology (Li-MnO2) is the key to this cell's exceptional performance. It enables a high rated voltage of 6 volts in a single compact unit and is able to deliver very high currents very quickly. This shortens the charging time between two flashes and ensures consistent performance for continuous shooting. The extremely low self-discharge guarantees maximum readiness for use even after many years of storage.Developed for maximum reliabilityThe CRP2 is manufactured to the highest quality standards to ensure maximum reliability and leak resistance. This protects your valuable and often sensitive equipment from damage. The protective single blister ensures that the battery retains its full power until it is used and can be safely stored against short circuits and external influences. Features Model VARTA Lithium photo battery CRP2 (single blister) Battery type Lithium manganese dioxide (Li-MnO2) Rated voltage (V) 6.0 Capacity (mAh) 1500 Dimensions (L x W x H in mm) 36.0 x 35.0 x 19.5 Weight (g) 38.0 FAQs about the VARTA Lithium Battery CRP2What is the main advantage of this lithium battery?The key advantage is its ability to deliver very high currents quickly (high drain), making it ideal for photo flashes and other high-performance applications. This is combined with the high voltage of 6V in a single battery, an extremely long shelf life and a wide temperature range.Is this battery rechargeable?No. This is a lithium primary battery. It must not be attempted to recharge it under any circumstances. Charging attempts are extremely dangerous and can lead to fire or explosion.Why is it called a "photobattery"?One of the main applications for this type of battery is to supply cameras and flash units with power. The high voltage and the ability to deliver power quickly are perfectly matched to the requirements of photography.How should this battery be disposed of?Batteries must not be disposed of with household waste. Please take the empty battery to the appropriate collection points in shops or municipal recycling centres to ensure environmentally friendly recycling.
PANASONIC Lithium battery BR-2/3A 3V 1200mAh
This PANASONIC BR-2/3A is a highly specialised 3-volt lithium battery developed for fail-safe memory backup in demanding industrial control systems. Based on the extremely reliable lithium polycarbon monofluoride technology (Li-(CF)n), this cell offers an exceptionally long service life and operating reliability, especially in high-temperature environments. As a ready-to-connect cell, it is the first choice for powering PLC controllers and other critical industrial applications.Highlights at a glanceMaximum reliability: Developed for fail-safe buffering of programme memories in PLC and industrial control systems.Extreme longevity: Very low self-discharge and a service life of up to 10 years.High temperature range: Guarantees stable performance in a wide operating temperature range from -40 °C to +85 °C.Stable voltage: Constant 3-volt voltage for the reliable supply of sensitive electronics.Assembled ready for connection: Equipped with the appropriate cable and plug for quick and error-free installation.Fail-safe power for industrial control systemsThis PANASONIC BR-2/3A battery is the preferred energy source for memory buffering in a variety of automation systems. It is typically used in programmable logic controllers (PLCs) and other industrial computers. Its main function is to reliably preserve volatile programme memory (SRAM) and system parameters in the event of a power failure or when the machine is switched off, thereby preventing costly data loss and reprogramming.Superior lithium polycarbon monofluoride technologyThe lithium polycarbon monofluoride technology (BR series) is the key to this battery’s exceptional reliability. Compared to lithium manganese dioxide technology (CR series), it offers even lower self-discharge and superior performance at very high ambient temperatures, as often found in control cabinets of industrial machinery. This guarantees maximum operational reliability throughout its entire long service life.Developed for professional useThis battery is designed as a direct replacement and OEM component. The assembly with the specific connector plug ensures quick, easy and, above all, reverse polarity protected replacement by technical personnel. The high quality of workmanship ensures a permanently reliable connection even under the vibrations of machine operation. Features ModelPANASONIC lithium battery BR-2/3A TechnologyLithium carbon monofluoride (Li-CF) Rated voltage (V)3.0 Capacity (mAh)1200 Dimensions (Ø x H in mm)17.0 x 33.5 ConnectionIndustrial cell (flat terminal) Weight (g)approx. 13.5 FAQs about the PANASONIC BR-2/3A battery packWhat is the main advantage of this lithium battery?The decisive advantage is its extreme long-term reliability, even at high temperatures. The very low self-discharge ensures that the battery remains ready for use for many years, making it ideal for low-maintenance backup applications in industrial control systems.Is this battery pack rechargeable?No. This is a lithium primary battery. It must never be attempted to recharge it under any circumstances. Charging attempts are extremely dangerous and may lead to fire or explosion.Why is the special plug so important?The pre-assembled plug is precisely matched to the connections of certain PLC controllers. This enables quick “plug-and-play” replacement and its coding prevents incorrect polarity, which could destroy the sensitive control electronics.How often does this battery need to be replaced?The replacement intervals depend on the control unit and environmental conditions and are specified by the machine’s manufacturer. Due to the very long service life of the battery, these intervals are typically several years.How should this battery be disposed of?Batteries must not be disposed of with household waste. As an industrial battery, it is subject to the provisions of the Battery Act. Please take the empty battery to the designated industrial or municipal collection points to ensure proper and environmentally friendly recycling.
Golden Power Alkaline Battery PX27A – 6V Special Battery (Replaces V27PX / 4LR43)
The Golden Power PX27A is a high-quality 6-volt alkaline special battery, specially developed to meet the energy needs of precision instruments and analogue cameras. It is the modern, environmentally friendly successor to the previously used PX27 mercury battery.Technically speaking, the PX27A is a stack of four LR43 button cells (hence the name 4LR43), which are combined in a custom-fit housing to form a 6V unit. This battery will breathe new life into your classics from Minox, Rollei or Yashica and ensures reliable exposure metering and shutter speeds.Highlights at a glanceExact fit: Replaces the classic types PX27, V27PX, KX27, HS3C and 4LR43 in analogue cameras and measuring devices.High voltage level: Provides constant 6.0 volts of energy for electronic shutters, light meters and remote controls.Mercury-free: Modern alkaline technology (0% Hg) as a safe and environmentally friendly alternative to banned mercury cells.Long shelf life: Thanks to high-quality seals and low self-discharge, the battery remains ready for use for years.Robust housing: The metal-clad construction protects against leakage and ensures stable contact in the battery compartment.Areas of applicationThe PX27A is a niche battery, but is essential for the use of certain vintage devices:Analogue cameras: Minox (C, EC, LX, TLX), Rollei (35 LED, A110), Yashica (Atoron Electro) and many more models from the 70s and 80s.Light meters: Various older handheld exposure meters.Remote controls: Older garage door openers or special infrared transmitters.Other: Electronic dog collars or medical measuring devices.Assembly & safety instructionsPolarity: When inserting the battery, pay meticulous attention to the "+ / -" marking. In many Minox cameras, the positive pole is often inserted in a particular direction (usually towards the lid) – check the engraving in the battery compartment.Voltage difference: The original PX27 (mercury) had 5.6 volts. This alkaline version has 6.0 volts. Most cameras with an electronic shutter (e.g. Minox C) tolerate this slight overvoltage without any problems thanks to internal voltage stabilisation. In pure rangefinder cameras, there may be minimal deviations in the exposure metering.Disposal: Empty batteries do not belong in household waste, but in the collection boxes in shops or at the recycling centre. Features Model / ReferenceGolden Power PX27A (special battery) Chemical system**Alkaline** (zinc-manganese dioxide) Rated voltage**6.0 V** Rated capacityapprox. **100 - 110 mAh** Dimensions (Ø x H)approx. **12.7 mm x 20.5 mm** Weightapprox. 7.0 g Alternative designationsV27PX, 4LR43, KX27, EPX27, HS-C, PX27A Typical applicationsClassic cameras (Minox, Rollei), remote controls, medical devices FAQs about Golden Power PX27AIs this battery rechargeable?No. This is a primary battery (single use). Never attempt to recharge an alkaline battery, as it may outgas or explode.Can I use four individual LR43 batteries instead?Theoretically yes, practically difficult. The PX27A internally consists of four LR43 cells. If you stack four individual LR43 cells in the compartment, you will have the same voltage (6V), but often the lateral support is missing (the diameter of the case is absent) and the contact becomes shaky. Moreover, stacking is "fiddly". The PX27A as a ready-made block is the much more reliable solution.How long does the battery last in a camera?That depends greatly on use. In a Minox camera that mainly uses the power for the shutter magnet and the LED display, a fresh PX27A often lasts 1 to 2 years with moderate use. Remove the battery when you are not using the camera for a long time to prevent leakage.
Varta Longlife zinc-carbon battery 430 / 4R25 6V
The Varta Longlife 430, internationally standardised as 4R25, is a robust and extremely long-lasting 6V block battery for continuous operation. Specialising in applications with low but constant energy requirements, it is the economical and reliable choice for safety lighting, agriculture and mobile use. Its proven zinc-carbon technology and practical spring contacts make it the standard solution for weeks of self-sufficient operation.Highlights at a glanceReliable continuous operation: Optimised for low-drain applications such as warning lights and electric fencing devices.Economical solution: Proven zinc-carbon technology for an excellent price-performance ratio.Robust design: Stable housing for demanding use on construction sites and outdoors.Secure connection: Practical spring contacts for easy, quick and vibration-resistant connection.High capacity: Long-lasting energy for weeks of low-maintenance operation.Specialist for construction site, agriculture and safetyThe Varta Longlife 430 is the preferred energy source for a wide range of professional applications. Its main area of use is to power construction site and warning lights, where it reliably ensures continuous or flashing operation. In agriculture, it is indispensable for operating electric fencing devices. It is also used in camping and leisure for large lanterns and lamps.Proven zinc-carbon technologyZinc-carbon technology is the ideal choice for devices with low and continuous energy consumption. Compared to alkaline batteries, it offers a very economical solution for this specific area of use, without compromising reliability. The Varta Longlife 430 is designed to deliver its energy slowly and consistently to achieve maximum runtime in continuous applications.Focus on functionality and safetyThe entire construction of this battery is designed for tough practical use. The impact-resistant housing protects the inner block from moisture and mechanical stress. The large spring contacts guarantee a simple but extremely effective and safe electrical connection, which is not interrupted by vibrations such as those found on construction sites. Features Model Varta Longlife 430 / 4R25 Battery type Zinc-carbon Rated voltage (V) 6 Capacity (mAh) 9300 Dimensions (L x W x H in mm) 115 x 67 x 67 Weight (g) 570 Connection Spring contacts FAQs about the Varta Longlife 4R25 batteryFor which devices is this battery mainly intended?This battery is ideal for devices with low, but long-lasting energy requirements. These include, above all, construction site warning lights, flashing lights, large camping lanterns and electric fencing devices.What is the difference to an alkaline version (4LR25)?The main difference is in the cell chemistry. The zinc-carbon version (4R25) is the more economical choice and perfect for devices with low, constant power consumption. The alkaline version (4LR25) is more expensive, but offers higher capacity and performance. It is better suited for devices with higher power consumption (e.g. bright halogen hand lamps) and for use at very low temperatures.What is the advantage of the spring contacts?The spring contacts enable very easy, tool-free and quick installation. They provide a secure and firm fit of the lamp head or connection cables and ensure a reliable power connection that is insensitive to vibrations.Is this battery rechargeable?No, the Varta Longlife 430 is a primary battery and cannot be recharged. Attempts to charge are dangerous and can cause the battery to leak or burst.How should this battery be disposed of?Batteries must not be disposed of in household waste. Please take the empty battery to the appropriate collection points in shops or municipal recycling centres to ensure environmentally friendly recycling.
Varta Longlife zinc-air battery 431 / 4R25X 6V
The Varta Longlife 431, internationally standardised as 4R25X, is a high-performance block battery based on zinc-air technology and developed for extremely long-lasting continuous applications. With its extremely high capacity, it provides a reliable supply of energy for months for devices with consistently low energy consumption. It is the first choice for professional applications in agriculture and traffic safety, where maximum autonomy and minimal maintenance are paramount.Highlights at a glanceExtreme longevity: Zinc-air technology for by far the highest energy density and longest lifetime of all 6V block batteries.Maximum cost-efficiency: Reduces operating costs through extremely infrequent battery replacements.Specialist for continuous use: Optimised for devices with low but constant energy consumption over many months.Robust construction: Sturdy housing for demanding outdoor use in all weather conditions.Secure connection: Practical screw terminals for a firm and absolutely secure connection.Specialist for agriculture and traffic safetyThe Varta Longlife 431 is specially designed for two main areas of application: powering electric fence devices and powering construction site and permanent warning lights. Its unique zinc-air chemistry enables these devices to be used for an entire grazing season or for months without changing the battery, making it the most efficient solution for hard-to-reach or maintenance-intensive installations.Innovative zinc-air technologyZinc-air technology utilises the oxygen from the surrounding air as an active component for the chemical reaction. To activate the battery, simply remove the adhesive strip from the air holes. After a short activation time, the cell supplies a constant voltage and a large amount of energy. This technology enables a capacity far above that of alkaline or zinc-carbon batteries.Focus on functionality and safetyThe entire construction of this battery is designed for maximum reliability in outdoor use. The impact-resistant housing protects the cells from weather influences and mechanical stress. The screw terminals ensure an extremely secure and permanent electrical connection that cannot come loose even with vibrations or exposure to the elements, which is essential for continuous use. Features Model Varta Longlife 431 / 4R25X Battery type Zinc-Air Rated voltage (V) 6 Capacity (mAh) 30000 Dimensions (L x W x H in mm) 115 x 67 x 67 Weight (g) 770 Connection Spring contacts FAQs about the Varta Longlife 4R25X batteryHow is this zinc-air battery activated?Before first use, the sealing adhesive strip must be removed from the battery's air holes. It takes a few minutes for enough atmospheric oxygen to penetrate the cell to achieve full power. Once activated, the process can no longer be reversed and the battery will slowly self-discharge.What is the difference compared to the 6V block batteries 4R25 (zinc-carbon) and 4LR25 (alkaline)?The main difference is the energy density. The zinc-air battery (4R25X) offers a three to four times higher capacity than the zinc-carbon version, and still a significantly higher capacity than the alkaline version. It is the absolute specialist for extremely long runtimes at low continuous current, as is typical for electric fences and warning lights.What is the advantage of the screw terminals?Screw terminals allow a particularly firm, secure and corrosion-resistant connection of the connecting cables. This is particularly important for outdoor use to ensure a permanently reliable contact even in the event of moisture and temperature fluctuations.Can I use this battery for a bright hand-held spotlight?No, it is not ideal for this. Zinc-air technology is optimised for devices with low continuous current. For applications with a high current requirement, such as a bright spotlight, an alkaline block battery (4LR25) is the better choice as it can supply higher currents.How should this battery be disposed of?Batteries must not be disposed of in household waste. Please take the empty battery to the designated collection points in stores or municipal recycling centres to ensure environmentally friendly recycling.
PANASONIC Lithium CNC Battery BR-CCF2TH 6V 5000mAh
The PANASONIC BR-CCF2TH is a highly specialised 6-volt lithium battery pack developed for fail-safe memory backup in demanding CNC control systems. Based on the extremely reliable lithium polycarbon monofluoride technology (Li-(CF)n) and assembled into a robust unit of two C-cells, this pack offers exceptionally long service life and operational reliability, especially in environments with high temperatures.Highlights at a glanceMaximum reliability: Developed for fail-safe buffering of programme memories in CNC and PLC control systems.Extreme longevity: Very low self-discharge and a service life of up to 10 years.High temperature range: Guarantees stable performance over a wide operating temperature range from -40 °C to +85 °C.Very high capacity: 5000 mAh for maximum self-sufficiency and long replacement intervals.Ready to connect: Equipped with the appropriate cable and connector for fast and error-free installation.Fail-safe energy for CNC machinesThe PANASONIC BR-CCF2TH battery pack is the preferred power source for memory buffering in a wide range of machine tools. It is typically used in CNC control units (e.g. from Fanuc) and other industrial computers. Its main task is to reliably maintain the volatile programme memories (SRAM), tool data and system parameters in the event of a power failure or when the machine is switched off, thus preventing costly data loss, machine downtime and time-consuming reprogramming.Superior lithium polycarbon monofluoride technologyLithium polycarbon monofluoride technology (BR series) is the key to this battery pack's exceptional reliability. In comparison to lithium manganese dioxide technology (CR series), it offers even lower self-discharge and superior performance at very high ambient temperatures, such as those often present in industrial machine cabinets. This guarantees maximum operational reliability throughout the long service life.Developed for professional applicationThis battery pack is designed as a direct replacement and OEM component. The assembly of the two cells with the specific connector plug ensures rapid, simple and, above all, reverse-polarity-proof replacement by technical staff. The high manufacturing quality ensures a permanently reliable connection even under the vibrations of machine operation. Features ModelPANASONIC Lithium CNC Battery BR-CCF2TH ApplicationMemory backup (CNC/PLC control units) TechnologyLithium carbon monofluoride (Li-CF) Nominal voltage (V)6.0 Capacity (mAh)5000 Cell arrangementSeries (2 cells side by side) Dimensions (L x W x H in mm)approx. 52 x 50 x 26 ConnectionCable with specific connector Weight (g)approx. 85 FAQs about the PANASONIC BR-CCF2TH battery packWhat is the main advantage of this lithium battery?The decisive advantage is the extreme long-term reliability, even at high temperatures. The very low self-discharge ensures that the battery remains ready for use for many years, making it ideal for low-maintenance backup applications in industrial control systems.Is this battery pack rechargeable?No. This is a lithium primary battery. It must not be attempted to be recharged under any circumstances. Charging attempts are extremely dangerous and can lead to fire or explosion.Why is the special connector so important?The pre-assembled connector is precisely matched to the connections of specific CNC controllers. This enables fast "plug-and-play" replacement and its coding prevents incorrect polarity, which could destroy the sensitive control electronics.How often does this battery need to be replaced?The replacement intervals depend on the control unit and the ambient conditions and are specified by the machine manufacturer. As a rule, the CNC controller itself signals when the backup battery voltage drops and replacement is required.How should this battery be disposed of?Batteries must not be disposed of with household waste. As an industrial battery, it is subject to the provisions of the Battery Act. Please take the empty battery to the designated industrial or municipal collection facilities to ensure proper and environmentally friendly recycling.
PANASONIC Lithium battery pack BR2/3AGCT4A 6V 2900mAh
The PANASONIC BR2/3AGCT4A is a highly specialised 6-volt lithium battery pack designed for fail-safe memory buffering (memory backup) in demanding industrial control systems. Based on extremely reliable lithium polycarbon monofluoride technology (Li-(CF)n) and assembled as a robust unit from four cells, this pack offers exceptionally long lifetime and operational reliability, especially in high-temperature environments. It is the first choice for supplying CNC controllers and other critical industrial applications.Highlights at a glanceMaximum reliability: Developed for fail-safe buffering of programme memory in CNC and PLC controls.Extreme longevity: Very low self-discharge and service life of up to 10 years.High temperature range: Guarantees stable performance in a wide operating temperature range from -40 °C to +85 °C.Stable voltage: Constant 6-volt voltage for the reliable supply of sensitive electronics.Ready for connection, assembled: Equipped with the proper plug for quick and error-free installation.Fail-safe power for industrial control systemsThe PANASONIC BR2/3AGCT4A battery pack is the preferred energy source for memory backup in a wide range of machine tools and automation systems. It is typically used in CNC controls by leading manufacturers such as Siemens (Simatic S5, S7) and Fanuc. Its main task is to reliably retain volatile programme memories (SRAM) and system parameters in the event of a power failure or shutdown of the machine, thus preventing costly data losses and reprogamming.Superior lithium polycarbon monofluoride technologyLithium polycarbon monofluoride technology (BR series) is key to the exceptional reliability of this battery pack. Compared to lithium manganese dioxide technology (CR series), it offers even lower self-discharge and superior performance at very high ambient temperatures, as frequently occurs in control cabinets of industrial machinery. This guarantees maximum operational reliability for the whole long service life.Developed for professional useThis battery pack is conceived as a direct replacement and OEM component. The assembly of the four cells in a robust holder and the equipment with the specific connector plug guarantee quick, simple, and above all reverse polarity-safe replacement by technical personnel. The high quality of workmanship ensures a continuously reliable connection even under the vibrations of machine operation. Features ModelPANASONIC Lithium battery pack BR2/3AGCT4A ApplicationMemory backup (CNC controls) TechnologyLithium carbon monofluoride (Li-CF) Nominal voltage (V)6.0 Capacity (mAh)2900 Cell arrangementBlock (2x2 cells) Dimensions (L x W x H in mm)approx. 34 x 34 x 34 ConnectionCable with specific plug Weight (g)approx. 60 FAQs about the PANASONIC BR2/3AGCT4A battery packWhat is the main advantage of this lithium battery?The crucial advantage is the extreme long-term reliability, even at high temperatures. The very low self-discharge ensures that the battery remains ready for use for many years, making it ideal for low-maintenance backup applications in industrial control systems.Is this battery pack rechargeable?No. This is a lithium primary battery. It must not be recharged under any circumstances. Attempts to charge are extremely dangerous and can lead to fire or explosion.Why is the special plug so important?The pre-assembled plug is precisely matched to the connections of certain CNC and PLC controls (e.g. from Siemens or Fanuc). This enables fast "plug-and-play" replacement and, thanks to its coding, prevents incorrect polarity that could destroy the sensitive control electronics.How often does this battery need to be replaced?Replacement intervals depend on the control unit and the ambient conditions and are specified by the machine manufacturer. Due to the very long service life of the battery, these intervals usually span several years.How should this battery be disposed of?Batteries must not be disposed of with household waste. As an industrial battery, it is subject to the requirements of the Battery Act. Please return the empty battery to the designated industrial or municipal reception points to ensure correct and environmentally friendly recycling.
PANASONIC Lithium CNC Battery BR-AGCF2W 6V 2200mAh
The PANASONIC BR-AGCF2W is a highly specialised 6-volt lithium battery pack designed for fail-safe memory backup in demanding CNC control systems. Based on extremely reliable lithium polycarbon monofluoride (Li-(CF)n) technology and assembled to a robust unit of two cells, this pack offers exceptionally long service life and operational reliability. It is the first choice for supplying CNC controllers from leading manufacturers such as Fanuc.Highlights at a glanceMaximum reliability: Developed for fail-safe buffering of programme memories in CNC controllers.Extreme longevity: Very low self-discharge and a service life of up to 10 years.High temperature range: Guarantees stable performance in a wide operating temperature range from -40 °C to +85 °C.Stable voltage: Constant 6-volt voltage for the reliable supply of sensitive electronics.Ready for connection: Equipped with the appropriate cable and connector for quick and error-free installation.Fail-safe energy for CNC machinesThe PANASONIC BR-AGCF2W battery pack is the preferred energy source for memory buffering in a wide range of machine tools. It is typically used in CNC controllers from Fanuc (e.g. Alpha series amplifiers) and other manufacturers. Its main function is to reliably maintain volatile programme memory (SRAM), tool data and system parameters in the event of a power failure or when the machine is switched off, thus preventing costly data loss, machine downtime and complex reprogramming.Superior lithium polycarbon monofluoride technologyLithium polycarbon monofluoride technology (BR series) is the key to the exceptional reliability of this battery pack. Compared with lithium manganese dioxide technology (CR series), it offers even lower self-discharge and superior performance at very high ambient temperatures, as often found in the control cabinets of industrial machinery. This guarantees maximum operational reliability over its entire long service life.Developed for professional useThis battery pack is designed as a direct replacement and OEM component. The assembly of the two cells with the specific connector ensures quick, simple and above all reverse-polarity-proof replacement by technical personnel. The high quality of workmanship guarantees a permanently reliable connection even under the vibrations of machine operation. Features ModelPANASONIC Lithium CNC Battery BR-AGCF2W ApplicationMemory backup (CNC/PLC controllers) TechnologyLithium carbon monofluoride (Li-CF) Nominal voltage (V)6.0 Capacity (mAh)2200 Cell arrangementSeries (2 cells side by side) Dimensions (L x W x H in mm)approx. 46 x 34 x 18 ConnectionCable with specific connector Weight (g)approx. 40 FAQs about the PANASONIC BR-AGCF2W battery packWhat is the main advantage of this lithium battery?The key advantage is the extreme long-term reliability, even at high temperatures. The very low self-discharge ensures that the battery remains ready for use over many years, making it ideal for low-maintenance backup applications in industrial controls.Is this battery pack rechargeable?No. This is a lithium primary battery. Under no circumstances should you attempt to recharge it. Attempting to do so is extremely dangerous and may cause fire or explosion.Why is the special connector so important?The pre-assembled connector is precisely matched to the connections of certain CNC controllers (especially Fanuc). This allows quick "plug-and-play" replacement and, thanks to its coding, prevents incorrect polarity, which could destroy the sensitive control electronics.How often does this battery need to be replaced?Replacement intervals depend on the control system and the operating conditions and are specified by the machine manufacturer. As a rule, the CNC controller itself signals when the voltage of the backup battery drops and replacement becomes necessary.How should this battery be disposed of?Batteries must not be disposed of with household waste. As an industrial battery, it is subject to the provisions of the Battery Act. Please take the empty battery to the appropriate industrial or municipal collection points to ensure proper and environmentally friendly recycling.
CNC battery 575332TA f
The CNC Battery 575332TA (often also referred to as Size 1/2 AA) is the essential backup power supply for classic Siemens Simatic S7-300 and S5 controllers. As a direct replacement for the original part number 6ES7971-1AA00-0AA0, this 3.0 volt lithium cell ensures that your automation systems do not suffer from memory loss.This battery buffers the RAM memory and the real-time clock (RTC) when the system is disconnected from the mains. A failure of this small component can mean the loss of the PLC program and all retentive data, leading to costly downtime and reprogramming. The high-quality lithium thionyl chloride technology (Li-SOCl2) guarantees an extremely long service life and shelf life.Highlights at a glancePerfect compatibility: 100% precision-fit replacement for the Siemens original battery 6ES7971-1AA00-0AA0.High voltage (3.0V): Uses lithium thionyl chloride chemistry for a stable voltage of 3.0 volts (unlike standard 3.0V lithium), which is absolutely essential for certain Siemens CPUs.Fully pre-assembled: Supplied complete with connection cable and the specific 2-pin connector. Old battery out, new in – done.Long service life: Thanks to extremely low self-discharge (< 1% per year at 20°C) the battery provides a standby time of up to 10 years (in storage) and several years in operation.Industry standard: Robust cell design (size 1/2 AA), resistant to temperatures and vibrations in the control cabinet.Data security: Protects against the loss of user programs, flags, counters and system data in the event of a power failure.Fields of applicationThis buffer battery is used in a wide range of Siemens automation components:Simatic S7-300: In almost all CPUs of the S7-300 series (e.g. CPU 312, 313, 314, 315, 316 etc.) that have a battery compartment (older models without Micro Memory Card concept or as RTC buffer).Simatic S5: S5-90U, S5-95U, S5-100U and other compact controllers.Sinumerik: Various CNC controllers from Siemens.Replacement for: Varta 6126, Tadiran SL-350, Saft LS14250 (each with the matching connector).Assembly & safety notesReplacement: Battery replacement should generally be carried out with the supply voltage switched on to the CPU to prevent data loss during the changeover.Diagnosis: Pay attention to the "SF" (collective fault) or specific "BATF" (battery fault) LED on the CPU. If this is lit (often yellow or red), the voltage is critically low.Plug direction: The plug is usually designed to be reverse polarity protected. Do not use force.Do not charge: Never attempt to charge this battery. There is a danger of explosion. Properties Model / ReferenceCNC Battery 575332TA (Replacement for 6ES7971-1AA00-0AA0) Chemical system**Lithium thionyl chloride** (Li-SOCl2) Voltage**3.0 V** (high-voltage lithium) Capacityapprox. **1200 mAh** (1.2 Ah) Design**1/2 AA** (Half mignon size) Connection**Cable with connector** (Reverse polarity protected for Siemens socket) Dimensions (cell)approx. 14.5 mm diameter x 25 mm height Compatibility**Siemens Simatic S7-300** (All CPUs of the 300 series), **S5-90U** Reference numbers6ES7971-1AA00-0AA0, 6ES7-971-1AA00-0AA0, SL-360/S TypeNon-rechargeable / Primary cell (Not rechargeable!) FAQs about the 575332TAIs this a 3V or 3.6V battery?This is a 3.0V battery. Many standard BIOS batteries have 3.0V, but Siemens S5/S7 controllers specifically require 3.0V for Li-SOCl2 technology. A 3.0V battery may be immediately detected as "empty" by the controller.How often should I change the battery?Siemens usually recommends a change every 12 months in the maintenance manual as a preventive measure. At the latest, however, when the battery LED comes on. Since the consequences of data loss are expensive, annual replacement is considered "best practice".Does this battery fit the S7-400?No. The S7-400 series mostly uses larger batteries (often size AA or mono cells buffered in the power supply unit), e.g. part number 6ES7971-0BA00. The 575332TA (1/2 AA) offered here is too small for the 400 series.
CNC Battery 1756BA2 f
The CNC Battery 1756BA2 is the indispensable energy insurance for your Allen Bradley ControlLogix control systems of the Series B. This 3.0-volt lithium battery has been specially developed to supply the volatile memory (RAM) of the CPU with power in the event of a power failure or shutdown of the system.While the 1756-BA1 is responsible for Series A, the revised processors of Series B absolutely require this type (1756-BA2). It reliably secures your PLC logic, variable values and system configurations. Failure of this small component can lead to hours of downtime if programmes have to be reloaded – this battery prevents this scenario cost-effectively.Highlights at a glanceSpecific for Series B: Exact replacement for the Allen Bradley part number 1756-BA2. Compatible with ControlLogix Series B processors (e.g. 1756-L61 Ser B).High-performance lithium: Utilises lithium manganese dioxide (Li-MnO2) technology for an extremely stable voltage of 3.0 V and high energy density.Plug & Play: Supplied as a complete assembly – lithium cell including permanently connected cable whip and the matching connector for the controller board.Long service life: Provides a typical operating life of 2 to 5 years (depending on the uptime of the machine) and a shelf life of up to 10 years.Data protection: Effectively prevents the loss of user programmes and real-time data (Real-Time Clock) in the event of power disconnection.Robust design: Withstands typical industrial environmental conditions such as vibrations and temperature fluctuations in the control cabinet.Areas of applicationThis battery is the standard replacement for the following Rockwell Automation / Allen Bradley components (each Series B):ControlLogix 5561 (1756-L61) Series BControlLogix 5562 (1756-L62) Series BControlLogix 5563 (1756-L63) Series BControlLogix 5564 (1756-L64) Series BControlLogix 5565 (1756-L65) Series BAssembly & safety instructionsBattery warning: As soon as the red "BAT" LED lights up on the controller, you often only have a reserve of a few days or weeks (with the machine switched off). Replace the battery immediately.Change under voltage: To avoid data loss, Allen Bradley often recommends changing the battery with the controller switched on (Power ON). Attention: Be sure to follow the safety regulations for working on live control cabinets (arc flash hazard, protection against accidental contact)!Observe the difference: Do not attempt to force a 1756-BA1 into a Series B controller. Brackets and connectors may vary.Storage: Store spare batteries in a cool, dry place to minimise self-discharge. Features Model / ReferenceCNC Battery 1756-BA2 (Allen Bradley replacement) Chemical system**Lithium** (LiMnO2) Voltage**3.0 V** Capacityapprox. **1200 mAh** (specific for Series B boards) Form factorSpecial cell (often 1/2 AA size or similar) with cable Connection**Cable with connector** (white, coded for Series B) Compatible CPUsControlLogix **Series B**: 1756-L61, L62, L63, L64, L65 TypeNon-rechargeable / primary cell (not rechargeable!) Weightapprox. 18 g Shelf lifeUp to 10 years (low self-discharge) FAQs about the 1756BA2What is the difference between 1756-BA1 and 1756-BA2?The main difference is in the controller series for which they are built.BA1: For ControlLogix 556x Series A.BA2: For ControlLogix 556x Series B. Although the cell itself is often similar (1/2 AA), connector polarity or cable length may vary. Always use the type specified by the manufacturer for your CPU revision.Can I use a rechargeable battery instead?No. The charging system of the PLC is not designed to charge a battery. These batteries are primary cells (disposable). A rechargeable battery would also have a high self-discharge and would not be able to backup the memory for months without power.How do I dispose of the old battery?Lithium batteries are hazardous waste. They must not be disposed of in residual waste. Tape the terminals of the old battery with insulating tape (risk of short circuit in the collection container) and take it to a certified collection point.
CNC Battery 1756BA1 f
The CNC Battery 1756BA1 is a high-quality lithium replacement battery specially developed for the requirements of Allen Bradley (Rockwell Automation) control systems. This 3.0-volt power source serves as a critical backup for the volatile memory (RAM) of your PLC controller.A failure of the buffer battery can have fatal consequences in industry: loss of the control programme, machine parameters or tool data. This battery ensures that your ControlLogix Series 5561, 5562, 5563 and 5564 controllers retain all data securely even in the event of a power failure or system shutdown. It is the cost-efficient and reliable alternative to the OEM part.Highlights at a glanceFull compatibility: Developed as a precisely fitting replacement for the Allen Bradley part numbers 1756-BA1, 1756-BA2 and 94194801.Lithium technology: The lithium cell (often Li-MnO2) offers a high energy density and a stable voltage of 3.0 Volt over almost the entire service life.Long shelf life: Thanks to a very low self-discharge rate (< 1% per year), this battery can be stored for up to 10 years and is reliable for years in use.Plug included: The battery is supplied as a finished assembly with cable and the specific 2-pin connector supplied. No soldering or tinkering is necessary ("Plug & Play").Data security: Protects against the loss of PLC programmes, system configurations and real-time clock (RTC) data in the event of a power failure.Industry standard: Robust construction that is resistant to vibrations and temperature fluctuations in control cabinets.Areas of applicationThis battery is essential for the following systems of the Rockwell Automation / Allen Bradley family:ControlLogix 5561 (1756-L61) processors (Series A).ControlLogix 5562 (1756-L62) processors (Series A).ControlLogix 5563 (1756-L63) processors (Series A).ControlLogix 5564 (1756-L64) processors (Series A).CNC controls: Used in various machine tools based on AB control technology.Installation & safety instructionsChange during operation: To prevent data loss during battery replacement, the battery should often be replaced while the controller (PLC) is powered on (Power ON). However, always check the manual for your specific controller beforehand to ensure that this is permitted and safe.Create backup: Always make a backup of the PLC programme to a non-volatile memory (e.g. CompactFlash card or PC) before replacing the battery to be on the safe side.Battery LED: Replace the battery immediately when the red "BAT" or "BATT LOW" LED on the front of the CPU lights up.Disposal: Lithium batteries do not belong in household waste. Dispose of the used battery in accordance with local regulations for hazardous materials. Features Model / ReferenceCNC Battery 1756-BA1 (Replacement for Allen Bradley) Chemical system**Lithium manganese dioxide** (LiMnO2) Voltage**3.0 V** Capacityapprox. **1800 mAh** Form factor (cell)2/3 A cell (cylindrical) Connection**Cable with 2-pin plug** (reverse polarity protected) Dimensions (cell)approx. 17 mm diameter x 35 mm height Compatible CPUsControlLogix 5561, 5562, 5563, 5564 (Series B) TypeNon-rechargeable / primary cell (Do not charge!) Weightapprox. 20 g FAQs about the 1756BA1How long does this backup battery last?In normal operation (when the machine is mostly switched on) the battery often lasts 2 to 5 years. The battery is only loaded when the machine is switched off. If the system is stored without power for a long period, the battery discharges more rapidly. Manufacturers often recommend a preventive replacement every 12 months.What happens if I don't change the battery?If the battery is empty and the machine is switched off (or the power fails), the RAM memory is deleted. The PLC programme and all parameters are lost. The machine must be reprogrammed/reloaded, which can lead to significant production downtime.Does this battery also fit Series B processors?Attention: The B series of ControlLogix L6x processors sometimes use other battery modules (e.g. 1756-BA2, which is often identical in design, or completely different modules for newer series such as L7x, which use capacitors). Always compare the connector and design with the old battery. The cell described here is a cylindrical cell attached to a cable.
CNC Battery A98L-0031-0012 f
The Fanuc A98L-0031-0012 is probably the most commonly installed backup battery in the world of CNC machining. It is a special 3.0-volt lithium cell of size 2/3 A, which serves in thousands of Fanuc controls (series i) and robot controllers as life insurance for memory.This battery supplies the SRAM memory and the absolute encoder (depending on the place of installation) with power when the machine is switched off. It stores machine parameters, zero points, tool corrections and CNC programmes. As the cell often serves for many years, its replacement is frequently forgotten – until the critical "BAT" alarm appears.Highlights at a glanceOriginal Fanuc specification: The part number A98L-0031-0012 designates the specific cell (often a Panasonic or Sanyo BR-2/3A), which is contained in the Fanuc order number A02B-0200-K102.High energy density (lithium): Uses lithium poly-carbon monofluoride chemistry (Li-CFn). This is not designed for high currents, but for extreme longevity and stable voltage over the years – ideal for memory backup.Format 2/3 A: A compact cylindrical cell (approx. 33.5 mm long) that is shorter than a standard AA battery, but thicker than a CR123A.Ready to plug-in installation: Delivered including cable and the special black Fanuc system connector (JAE 2-pin with locking nose). No soldering required.Long service life: Typically offers an operating period of 3 to 5 years in the CNC machine. The self-discharge is so low that it can be stored for up to 10 years.Critical data protection: Prevents the loss of system parameters (parity error), which on older machines would often mean manual re-entry of hundreds of parameters.Areas of applicationThis battery is found in a very wide range of Fanuc devices:CNC controls: Fanuc Series 0i (0i-Mate, 0i-B, 0i-C, 0i-D), 16i, 18i, 21i, 30i, 31i, 32i.Robot controller: Fanuc R-J3iB, R-30iA Mate (often in the controller housing or in the base of the robot).Power Mate: Series iD, iH.Position: Usually directly behind the screen (LCD) or in a small compartment on the CNC unit inside the control cabinet.Installation & safety instructionsGolden rule: Replace the battery only when control is switched on (Power ON). The system is buffered for only approx. 20 minutes by a capacitor when switched off. If you remove the old battery and have trouble inserting the new one (e.g. connector stuck), the memory is cleared. With the machine switched on, this risk does not exist.Attention high voltage: Work carefully in the control cabinet. Do not touch any live parts near the control.Reset: After the change, the error message ("BAT" flashes or alarm) usually does not have to be acknowledged manually; it disappears as soon as the voltage is > 2.8V again.Connector coding: Pay attention to the "nose" on the black connector. There are similar batteries with brown connectors (different coding) which do not fit mechanically. Do not use force. Features Model / Fanuc Ref.CNC battery A98L-0031-0012 Chemical system**Lithium poly-carbon monofluoride** (BR series) Voltage**3.0 V** Capacityapprox. **1200 mAh** (standard for 2/3A) Format (cell)**2/3 A** (Cylindrical, short and wide) Dimensions (cell)approx. 17 mm Ø x 33.5 mm height Connection**JAE connector 2-pole** (coded for Fanuc board) CompatibilityFanuc Series **0-C, 0-D**, Series **15-B**, 16/18/21 (older revisions), Power Mate iH TypeNon-rechargeable / primary cell Weightapprox. 18 g FAQs for A98L-0031-0012What is the difference to A98L-0031-0025?That is a big difference!A98L-0031-0012: Small cell (2/3 A), black connector. Mostly for the CNC control (display).A98L-0031-0025: Large cell (type C or D in housing), grey box. Mostly for the servo amplifier (buffering of the axis position). Do not mix these up, they do not fit mechanically.My screen displays "APC Alarm 307" – is this the battery?Probably not. APC alarms (Absolute Pulse Coder) usually refer to the batteries in the axis amplifiers (servo drives), not to the battery in the CNC unit. The battery of the CNC unit usually causes system alarms or a flashing "BAT" in the status line. Check your machine's manual.Why is the battery so expensive compared to supermarket batteries?This is an industrial lithium cell (not alkaline manganese). It has a special chemistry for long-term stability (10 year shelf life) and a very wide temperature range (-40 to +85 degrees), to avoid failure in a hot control cabinet. A standard battery would quickly fail here and cause expensive damage.
CNC Battery A02B-0200-K102 f
The CNC battery A02B-0200-K102 (often identified by the cell part number A98L-0031-0012) is a specialised 3-volt lithium backup battery. It is the life insurance for the control data of your Fanuc i-series (16i, 18i, 21i) as well as compatible machines such as the Le Blonde 77.This battery secures the SRAM memory of the CNC controller. It stores critical data such as CNC parameters, tool offsets, workpiece zero points and the PLC program (ladder). A failure of this battery leads to the immediate loss of this data ("System Parity Error"), which results in a complete machine standstill and a costly restoration of the parameters.Highlights at a glanceOriginal specification: Developed as an exact replacement for the Fanuc order number A02B-0200-K102. The actual cell often bears the identification A98L-0031-0012.High reliability: Uses lithium poly-carbon monofluoride (BR series) chemistry (mostly Panasonic BR-2/3A), which is specially designed for long-term applications with low discharge.Voltage: 3.0 Volt.Capacity: 1,200 mAh (High Capacity for size 2/3 A).Ready to plug in: Delivered as assembly with cable and the specific black 2-pin connector (JAE type), which fits exactly to the Fanuc board.Long life: Typical durability of 3 to 7 years in operation (depending on the operating time of the machine) and up to 10 years shelf life.Areas of applicationThis battery is compatible with a wide range of Fanuc controllers and servo systems, especially:Fanuc Series 16i / 160i / 162iFanuc Series 18i / 180i / 182iFanuc Series 21i / 210i / 212iFanuc Power Mate iD / iHLe Blonde 77 CNC (if equipped with Fanuc control)Location: Mostly behind the LCD display or in a special battery compartment on the CNC unit.Installation & Safety AdviceThe most important rule: Always replace the CNC buffer battery ALWAYS with the machine powered on (Power ON).Reason: If you switch off the machine and remove the old battery, the capacitor on the board will only buffer for about 20-30 minutes. If the replacement takes longer or the capacitor is old, the memory will be erased. With the machine powered on, the power supply provides the memory and the change is safe.Note the alarm: Replace the battery immediately if the display shows the message "BAT" is flashing or the alarm "Battery Low" (often alarm code APC 300 series or system alarm) appears. Do not wait until the next maintenance interval.Position: The battery is often located on the rear of the display unit (MDI/CRT Unit) under a small yellow or black cover. Features Model / Fanuc Ref.CNC battery A02B-0200-K102 (Fanuc) OEM reference (cell)**A98L-0031-0025** (often printed on the housing) Chemical system**Lithium poly-carbon monofluoride** (BR series) Voltage**3.0 V** Capacityapprox. **1200 mAh** Design**2/3 A** (Cylindrical, short) Dimensions (cell)approx. 17 mm Ø x 33.5 mm height Connection**JAE connector 2-pin** (special connector for Fanuc board) CompatibilityFanuc Series **16i, 18i, 21i**, Power Mate iD/iH, 0i-B TypeNon-rechargeable (Not rechargeable!) FAQs for A02B-0200-K102Is this the battery for the drives (servos) or the controller?The A02B-0200-K102 (A98L-0031-0012) is primarily the battery for the CNC controller (memory backup). For the servo amplifier (absolute axis position) often other batteries are used (e.g. large mono D cells or the A98L-0031-0025 in the black box). Check exactly which alarm message you have ("System Battery" vs. "APC Battery").My battery has a brown connector, this one has a black one. Will this fit?Caution. The connector (JAE) has a mechanical coding (nose).A98L-0031-0012: Black connector (for i-series controllers).A98L-0031-0026 / -0028: Often brown or cream-coloured connector (for Beta drivers or older systems). Compare the nose on the connector exactly with your old part. Forcing it will damage the connection on the expensive CNC board.Can I use a standard CR123A battery?No. Although they look similar, photo batteries (CR123A) have different dimensions and do not have solder tags/connectors. DIY solutions with adhesive tape in vibration-rich CNC machines risk loose contacts and data loss.
CNC battery for Fuji Electric Micrex-F ( Fuji CREXF / FBT030A)
The search term "TOSMICREXF" is a common designation (often used by third-party suppliers) for the buffer battery of the Fuji Electric Micrex-F PLC series (Programmable Logic Controller). These controllers were frequently installed in machine tools (also by TOS).The technically correct designation for this battery is usually FBT030A or the underlying cell CR8-LHC. This is a powerful 3.0 volt lithium cell that backs up the RAM memory of the CPU (programmes, parameters, tool data) when the machine is switched off.Highlights at a glanceIdentification: Replaces the original part numbers FBT030A, FBT020A and often CR8-LHC.System compatibility: Especially for the Fuji Micrex-F series (models F30, F50, F55, F70, F80, F80H, F100, F120, F120H).High capacity: Utilises a "high capacity" lithium cell (approx. 3000 mAh) to guarantee the long buffer times of old systems.Ready to plug in: Supplied with cable and the specific white 2-pin connector with locking lug supplied.Long-term protection: Prevents the loss of the PLC programme (ladder logic) and the machine parameters.Important note on the designThere are different batteries within the Micrex-F series. Please check your old part before ordering:The "big one" (described here): Approx. 45 mm long (CR8-LHC / FBT030A). This is the standard for most Micrex-F CPUs.The "little one": Approx. 27 mm long (CR2-L / PM-20). This is rarely used.Connector: The connector of the "TOSMICREXF" is usually white and has a small lug for locking on the circuit board.Assembly & SafetyChange under voltage: To avoid data loss, the battery must be with control switched on (Power ON) must be replaced. Do not switch off the machine while removing the old battery, otherwise the memory will be deleted immediately!Alarm LED: Replace the battery as soon as the red "ALM" or "BATT" LED on the CPU lights up.Reset: For some Micrex-F CPUs, the battery error must be reset after replacement using a reset button or command.Features Model / ReferenceFuji Electric FBT030A (Also: TOSMICREXF) Chemical system**Lithium thionyl chloride** (Li-SOCl2) Rated voltage**3,6 V** Battery capacityapprox. **1600 - 2000 mAh** (depending on cell charge) Design**2/3 A** (often also referred to as ER17/33) Dimensions (cell)approx. 17 mm Ø x 33.5 mm height Connection**Cable with special plug** (white, 2-pin connector, Fuji coding) Compatibility**Fuji Micrex-F** series, **Toshiba PROSEC T** series Battery lifeapprox. 3 to 5 years (in buffer mode) weightapprox. 20 g FAQs for TOSMICREXF (Fuji FBT030A)What is the difference between FBT020A and FBT030A?The difference lies in the capacity and size.FBT020A (CR6-L): Often has approx. 1600 mAh.FBT030A (CR8-LHC): Has approx. 3000 mAh (high capacity). Both have 3.0V and usually the same white connector. The FBT030A lasts significantly longer and is recommended for machines that are often switched off. Mechanically, the larger FBT030A usually fits into the same holder, as this is often just a clip.Do I have to delete an error after the change?Yes, often. With the Micrex-F series, the "BATT" LED sometimes does not disappear automatically. You may need to press a reset button on the CPU (depending on the CPU model) or acknowledge the alarm in the system menu. Check the manual for your specific control unit (F80, F120 etc.).Can I use a normal photo battery (CR123A)?No. Although both have 3.0 volts, the CR123A has different dimensions and no connector. Soldering on lithium batteries is dangerous (risk of explosion!). In addition, CR123A batteries are often not optimised for years of micro-discharge current (memory backup), but for high currents (flash). Use the original industrial cell for data security.
Fuji Special CR8-LHC f
The Fuji Special CR8-LHC is a high-capacity lithium buffer battery specially designed for the Fuji Electric Micrex-F and Micrex-SX PLC control series. This 3.0-volt power source secures the internal RAM memory.The addition "LHC" (High Capacity) indicates a particularly high energy density. Compared to standard buffer batteries, this model offers an extended service life, significantly prolonging maintenance intervals in large industrial plants. It reliably protects your programmes, machine data and calibration values from loss in the event of power failure or system shutdown.Highlights at a glanceSpecific for Fuji Electric: Perfect replacement for part numbers CR8-LHC, FBT020A or FBT030A (please compare plug).High Capacity (3000 mAh): With a capacity of about 3000 mAh this cell provides an extremely high energy reserve. This is especially important for older controllers or systems with long downtimes.Lithium technology: Uses lithium manganese dioxide (Li-MnO2) for a stable voltage of 3.0 V throughout the entire lifetime.Ready to install: The battery is supplied as an assembly, including cable and the specific white system connector (often with latch), exactly fitting the CPU board.Long lifetime: Thanks to extremely low self-discharge (< 1% per year) the battery can be stored for up to 10 years and often lasts 5+ years in operation.Industrial quality: The cylindrical steel housing protects against leakage and withstands typical vibrations in control cabinets.Areas of applicationThis battery is primarily found in the following systems:Fuji Electric Micrex-F series: F30, F50, F55, F70, F80, F80H, F120, F120H.Fuji Electric Micrex-SX series: SPH, SPB.Various CNC controls: Based on Fuji hardware.Installation & safety instructionsReplacement under voltage: As with almost all PLC systems, the battery must be replaced while the controller is powered (Power ON) to avoid data loss.Observe alarm: The CPU usually indicates a weak battery with an LED (BATT or ALM). Do not delay replacement, as the remaining runtime is often just a few weeks.Plug check: There are various versions of Fuji batteries. Compare your old plug to the spare part. The CR8-LHC usually has a slightly larger, white plug compared to the smaller CR2-L versions.Reset: After installing the new battery, the battery error must often be cleared by a reset or restart (see CPU manual). Features Model / ReferenceFuji Special CR8-LHC (original spare part) Chemical systemLithium manganese dioxide (LiMnO2) Voltage3.0 V Capacityapprox. 2600 - 3000 mAh (High Capacity) DesignCylindrical (similar to A-cell, but special size) Dimensions (cell)approx. 17 mm Ø x 45 mm height ConnectionCable with connector (specific for Fuji Micrex board) CompatibilityFuji Electric MICREX-F series (F30, F50, F55, F70, F80 etc.) TypeNon-rechargeable / primary cell (Not rechargeable!) Weightapprox. 22 - 25 g FAQs for Fuji CR8-LHCWhat is the difference to CR6-L or CR2-L?The difference is in the size and capacity.CR2-L: Small, short cell (often for compact CPUs).CR6-L: Medium size.CR8-LHC: Large cell (approx. 45mm long) with the highest capacity (3000mAh) for maximum buffer time. Mechanically, they often do not fit in the same holder, so the part number is crucial.Can I recharge the battery?No, absolutely not. This is a primary cell (disposable). Attempting to charge can cause an explosion or chemical leakage, which would destroy the expensive PLC board.How long can I store the battery?Thanks to lithium technology, you can easily store this battery for 10 years on the shelf (at room temperature). It is advisable to always keep a spare battery in stock so that you can react immediately in the event of an alarm.
PANASONIC Lithium CNC Battery BR-CCF1TH 3V 5000mAh
The PANASONIC BR-CCF1TH is a highly specialised 3-volt lithium battery pack developed for fail-safe memory buffering (Memory Backup) in demanding CNC controllers. Based on extremely reliable lithium polycarbon monofluoride technology (Li-(CF)n) and assembled with a specific connector, this pack offers exceptionally long service life and operational reliability, especially in high-temperature environments.Highlights at a glanceMaximum reliability: Developed for fail-safe buffering of programme memories in CNC and PLC controllers.Extreme longevity: Very low self-discharge and a service life of up to 10 years.Wide temperature range: Guarantees stable performance over an extensive operating temperature range of -40 °C to +85 °C.Very high capacity: 5000 mAh for maximum autonomy and long replacement intervals.Ready-to-connect configuration: Supplied with the suitable cable and plug for fast and error-free installation.Fail-safe energy supply for CNC machinesThe PANASONIC BR-CCF1TH battery pack is the preferred energy source for memory buffering in a wide variety of machine tools. It is typically used in CNC controllers and other industrial computers. Its main function is to reliably maintain volatile programme memory (SRAM), tool data and system parameters in the event of a power failure or machine shutdown, thus preventing costly data loss, machine downtime and laborious reprogramming.Superior lithium polycarbon monofluoride technologyLithium polycarbon monofluoride technology (BR Series) is the key to the outstanding reliability of this battery pack. In comparison to lithium manganese dioxide technology (CR Series), it offers even lower self-discharge and superior performance at very high ambient temperatures, such as those often encountered in the control cabinets of industrial machines. This guarantees maximum operational reliability over the entire long service life.Developed for professional useThis battery pack is designed as a direct replacement and OEM component. The assembly with the specific connector ensures rapid, simple, and above all, reverse polarity-proof replacement by technical personnel. The high-quality workmanship guarantees a consistently reliable connection even under the vibrations of machine operation. Features ModelPANASONIC Lithium CNC Battery BR-CCF1TH ApplicationMemory backup (CNC/PLC controllers) TechnologyLithium carbon monofluoride (Li-CF) Nominal voltage (V)3.0 Capacity (mAh)5000 Cell arrangementSingle cell (BR-C) with cable Dimensions (Ø x H in mm)26.0 x 50.0 ConnectionCable with specific connector Weight (g)approx. 42 FAQs about the PANASONIC BR-CCF1TH battery packWhat is the main advantage of this lithium battery?The key advantage is the extreme long-term reliability, even at high temperatures. The very low self-discharge ensures that the battery remains ready for use for many years, making it ideal for low-maintenance backup applications in industrial controllers.Is this battery pack rechargeable?No. This is a lithium primary battery. It must never be recharged under any circumstances. Attempting to charge it is extremely dangerous and may cause fire or explosion.Why is the special connector so important?The pre-assembled connector is precisely matched to the connections of certain CNC controllers. This enables quick "plug-and-play" replacement and, thanks to its coding, prevents incorrect polarity which could damage sensitive control electronics.How often does this battery need to be replaced?Replacement intervals depend on the controller and the ambient conditions and are specified by the machine manufacturer. Normally, the CNC controller itself indicates when the backup battery voltage drops and replacement is required.How should this battery be disposed of?Batteries must not be disposed of in household waste. As an industrial battery, it is subject to battery legislation. Please hand the empty battery into the designated industrial or municipal collection points to ensure proper and environmentally friendly disposal.
Duracell Plus alkaline battery MN1203 single blister
The Duracell Plus 9V, also known as MN1203, is the reliable alkaline block battery for a variety of everyday and safety-critical devices. As a quality product from the globally recognized brand Duracell, it provides long-lasting, consistent power supply and high leak protection. It delivers a nominal voltage of 9 V and is the ideal choice for devices such as smoke alarms, measuring devices, and toys. Delivery is in a practical individual blister pack that protects the battery until use.Highlights at a glanceBrand quality: Reliable and long-lasting energy from Duracell.Safety specialist: Ideal for smoke detectors, alarm systems and measuring devices.Long shelf life: Thanks to Duralock Power Preserve technology, can be stored for up to 5 years.High performance: 9 V voltage for a constant and powerful energy output.Packaging: Secure individual blister for convenient handling and storage.Powerful in a variety of applicationsThe Duracell Plus 9V block battery is the universal power supply for countless electronic devices where a 9-volt supply is required. It is the first choice for safety-relevant applications such as smoke alarms and carbon monoxide detectors, where absolute reliability is essential. In addition, it is used in measuring devices such as multimeters, in remote controls, scales, wireless microphones, effect devices, and in electronic toys.Reliable alkaline technologyThe alkaline manganese technology used (Zn/MnO2) stands for high capacity and an excellent price-performance ratio. Compared to simple zinc-carbon batteries, it offers a significantly longer life span and better performance. The high-quality workmanship of Duracell and the Duralock technology also ensure a high level of tightness and reliably protect your devices from damage caused by leakage.Efficiency and safety with a systemDuracell batteries are subject to strict quality controls to ensure consistently high performance and maximum safety. The guaranteed shelf life of 5 years gives you the assurance of always having a ready-to-use battery available, especially for the important annual replacement in smoke alarms. The single packaging protects the cell from short circuits and environmental influences until used. Characteristics ModelDuracell Plus Alkaline Battery MN1203 (3LR12) ApplicationEveryday devices, lanterns, experiments TechnologyAlkaline manganese (alkaline) Nominal voltage (V)4.5 Capacity (mAh)approx. 6100 Dimensions (L x W x H in mm)67 x 62 x 22 ConnectionFlat contacts (+ wide / - narrow) Weight (g)approx. 170 FAQs about the Duracell Plus 9V batteryWhat do the designations MN1203 and 6LR61 mean?MN1203 is Duracell's traditional ANSI designation for this battery type. 6LR61 is the international IEC standard designation for a 9-volt alkaline block battery. Both designations describe the same compatible battery type.How long can this battery be stored?Thanks to Duracell Duralock Power Preserve technology, this 9-volt battery can be stored for up to 5 years if kept in a cool, dry place without significant loss of capacity.Why should I use this battery for smoke alarms?The Duracell Plus is designed for long-lasting and reliable power output in low power consumption applications, such as smoke alarms. Its high quality and leak protection provide the necessary operational safety for these essential devices.How should this battery be disposed of?Batteries must not be disposed of in household waste. Please take the empty battery to the designated collection points in retail stores or municipal recycling centres to ensure environmentally safe recycling.