Solar cable red 50m 4mm² IEC62930 – SOLR450 for reliable PV installations

The solar cable SOLS450 (50 metres, 4mm²) in black is the ideal metered cable for photovoltaic projects that require flexible and secure wiring over medium distances. With a length of 50 metres, this roll offers ample scope for string cabling on rooftops or for connecting module arrays to the inverter. The black colouring is used for standard-compliant identification of the negative pole (-), which makes installation straightforward and minimises connection errors.Certified to the international standard IEC 62930, this cable fulfils the highest requirements for safety and durability. It is specially designed for the harsh conditions outdoors and, thanks to its high-quality material composition, ensures efficient energy transmission over the entire service life of your solar installation.Highlights at a glanceCertified standard: Complies with standard IEC 62930 (H1Z2Z2-K), which guarantees maximum suitability for photovoltaic DC systems up to 1500V.Generous range: 50 metres in one piece allow uninterrupted installation without additional connectors between module array and technical room.Clear polarity: The black outer sheath provides clear visual separation of the negative cable, increasing safety during installation and maintenance.Weather- & UV-resistant: The quality XLPO double insulation provides lasting protection against embrittlement from sunlight, ozone, and extreme weather.Optimum conductivity: The finely stranded conductor made from tinned copper provides excellent corrosion protection and permanently low transition resistances.High thermal load capacity: Reliable operation in a wide temperature range from -40°C to +90°C.Areas of applicationThe SOLS450 is the ideal choice for a wide variety of installation scenarios:Single-family homes & rooftop systemsPerfect for connecting the solar modules to the inverter when it is installed in the basement or utility room.Balcony systems & garden installationsIdeal for installations where a greater distance between the panels and the feed-in point needs to be bridged.Mobile solar systemsUse in self-sufficient systems for tiny houses or larger mobile homes, where certified industrial quality is important.Installation & safety instructionsProfessional connectionFor assembly, use only high-quality MC4 connectors and ensure precise crimping with special solar crimping pliers.Mechanical fixationFasten the cable at regular intervals with UV-resistant cable ties to minimise mechanical stress from wind or self-weight.Avoiding induction loopsLay the black negative cable as parallel and as close as possible to the red positive cable to reduce electromagnetic interference and the risk of lightning induction. Features Model / SKU**SOLS450** Conductor cross-section**4.0 mm²** Delivery form**50 metre ring** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (finely stranded) Temperature range-40°C to +90°C (ambient) Certificates**IEC 62930 / EN 50618 (H1Z2Z2-K)** Special featureHalogen-free & short-circuit proof  FAQs about the solar cable black 50m 4mm²Why is IEC 62930 certification important?It guarantees longevity in PV systems.This standard ensures that the cable is halogen-free, flame-retardant and specially tested against stresses from high DC voltages and UV light. This distinguishes it significantly from conventional installation cables.Is 4mm² sufficient for a 50m long cable?Yes, for moderate currents.In a typical module string with high voltage, the voltage drop at 50 metres and 4mm² is usually completely unproblematic. For systems with very low voltages (e.g. 12V), however, the voltage drop should be checked in advance.Is the cable resistant to acids and alkalis?Yes.The XLPO insulation provides good resistance to chemical influences, which is particularly advantageous for installations near industrial areas or in agriculture (ammonia exposure).

The Deye SE-G5.1Pro-B is a powerful battery module with 5.12 kWh storage capacity based on safe lithium iron phosphate technology (LiFePO₄). With its modular design, support for high-current applications and its flexibility in installation, it is the ideal solution for modern energy storage systems in private and commercial settings.Highlights at a glanceSafe & durable: Cobalt-free LiFePO₄ cells with intelligent BMS Modular and scalable: Up to 64 modules – max. 327 kWh storage capacity High compatibility: Suitable for wall mounting, floor mounting & 19" rack Easy maintenance: Automatic networking, remote monitoring & USB firmware updates Reliable operation: IP20, natural cooling, wide temperature range down to -20 °CCompact, scalable & intelligently networkedWith a single capacity of 5.12 kWh, the Deye SE-G5.1Pro-B is ideal for smaller storage solutions or as a module in large modular storage systems. Thanks to the possibility to connect up to 64 units in parallel, a maximum total capacity of 327 kWh is possible. Perfect for applications with increasing energy needs. Automatic network addressing as well as support for firmware updates via USB or remote access make commissioning and maintenance much easier.Flexible to mount – space-saving & installation-friendlyThanks to three mounting options, rack mounting (19 inch), wall mounting or floor installation, the module can be optimally positioned in almost any environment. With its compact form of only 133 mm height, it saves valuable space in technical rooms or living areas.Who is the Deye SE-G5.1Pro-B suitable for?Private households looking for a safe and future-proof storage system Commercial enterprises requiring scalable storage solutions for self-consumption or backup System integrators & installers who value easy integration and low maintenance  Sustainability-orientated users who rely on environmentally friendly storage technology ModelDEYSE-G5.1 Pro-B Battery typeLiFePO4 Module capacity (kWh)5.12 Module nominal voltage (V)51.2 Module capacity (Ah)100 System nominal voltage (V)51.2 System operating voltage (V)43.2-57.6 System capacity (kWh)5.12 System usable capacity (kWh)4.6 Charge/discharge current (A) - Recommendation50 Charge/discharge current (A) - Nominal value100 Charge/discharge current (A) - Peak discharge (2 min,25°C)150 Operating temperature (°C)Charge: 0 ~ 55 / Discharge: -20 ~ 60 LCD displaySOC%, Power, Total Voltage Communication portCAN2.0, RS485 Humidity5% ~ 90% Altitude≤2000m IP protection class of the housingIP65 Storage temperature (°C)0 ~ 35 Dimensions (W/D/H, mm)440 * 133 * 540 Weight (kg)45 Installation locationFloor mounting, rack mounting Recommended depth of discharge90% Cycle lifetime25 ± 2°C, 0.5C/0.5C, EOL70% ≥ 6000 Warranty10 years CertificationsUN38.3, IEC62619, CE,UK, VDE2510-50, CEI 0-21, FCC, UL1973, UL9540A  FAQs about the Deye SE-G5.1Pro-B battery storage unitHow much energy is actually usable?One module delivers 5.12 kWh gross capacity, of which around 4.6 kWh is usable at 90% depth of discharge, particularly suitable for private and commercial applications.What voltage and currents apply per module?The module operates at 51.2 V nominal voltage and 100 Ah capacity. The continuous current is 50 A, with up to 150 A possible for 10 seconds at peak.How many modules can be combined?In the IP20 version, up to 64 modules can be connected in parallel, giving a total capacity of over 327 kWh. For home use: six modules per stack, i.e. 30.7 kWh per unit.How long does the module last?The cells achieve over 6,000 cycles at 90 % DoD, with a residual capacity of at least 70 % at the end of life, so they are designed for long-term use.Which Deye inverters is the system compatible with?The battery is officially released for all three-phase hybrid inverters of the SUN-xK-HP3 and SUN-xK-BM series, fully plug-&-play enabled without additional modifications. Scope of delivery Deye SE-G5.1Pro-B rack battery module (5.12 kWh): Module typeThis is a single, flexible low-voltage battery module for installation in 19-inch racks, for wall mounting or floor mounting.1 x Deye SE-G5.1Pro-B battery module (5.12 kWh)The central storage unit with 5.12 kWh (100 Ah) in rack format, including an intelligent, integrated battery management system (BMS).1 x set of mounting handles / rack earsHandles for easier handling and for attaching the module in a 19-inch rack.1 x set of battery connection cables (plus & minus)A pair of pre-assembled high-performance cables for connecting the module (or the battery stack) to a compatible hybrid inverter.1 x communication cable (CAN/RS485)A data cable for communication between the battery module and the inverter.1 x parallel connection cable (power & communication)Short cables to connect the power and data bus of this module to another module.1 x earthing cableA protective conductor cable for proper earthing of the housing.1 x operating and installation manualA printed manual that describes the various installation methods (rack, wall, stack).2 x wall bracketsFor wall mounting of the battery pack 4 x feetFor stacking and securing the battery

The Deye SUN-8K-SG05LP3-EU-SM2 is a powerful three-phase hybrid inverter. It has been specifically designed for residential and commercial applications, combining an inverter, battery charger and intelligent energy management system in a single device. This all-in-one solution is ideal for new installations as well as retrofitting existing photovoltaic systems and reliably maximises self-consumption and energy efficiency.Highlights at a glanceSupports both lead-acid and lithium-ion batteries for flexible storage solutionsBattery voltage range from 40 to 60 volts for different storage requirementsMaximum charging and discharging current of 190 amps enables fast energy transferMaximum PV input power of 12,000 watts for larger photovoltaic systemsUnbalanced output power with up to 50 percent of the rated power per phase enables flexible load distributionParallel connection of up to 10 devices for customisable system sizesEfficient energy conversion for modern requirementsThe Deye SUN-8K-SG05LP3-EU-SM2 offers a maximum efficiency of 97.6 percent and an MPPT efficiency of over 99 percent. The wide MPPT voltage range of 200 to 650 volts ensures that a high energy yield is achieved even with changing irradiation conditions. With a maximum PV input voltage of 800 volts, the inverter is optimally suited for high-performance solar module fields. This helps to sustainably increase the efficiency and profitability of the photovoltaic system.Flexibility and scalabilityThe Deye SUN-8K-SG05LP3-EU-SM2 can be flexibly adapted to different requirements. With the option of operating up to ten devices in parallel, the system can be scaled for both smaller and larger energy projects. AC coupling enables simple integration into existing solar systems without the need for extensive modifications. Thanks to the support of both battery types, lead-acid and lithium-ion, the inverter offers a high degree of adaptability to individual storage solutions.Reliability and protectionWith a protection class of IP65, the inverter is optimally protected against dust and water and is therefore suitable for use in a wide variety of environments. The operating temperature range of minus 40 to plus 60 degrees Celsius ensures reliable operation even in extreme weather conditions. Extensive protection functions such as overcurrent, overvoltage, short-circuit and thermal protection, DC reverse polarity protection and monitoring of the DC insulation impedance ensure a high level of operational safety and a long service life for the device.Who is the Deye SUN-8K-SG05LP3-EU-SM2 suitable for?This inverter is ideal forHomeowners seeking a powerful and flexible solution for self-consumption and grid independenceCommercial operations that require stable and efficient power supplyUsers wishing to retrofit existing solar systems with modern storage solutionsInstallations in regions with fluctuating grid supply, where diesel generators provide additional security of supply  ModelDEYE SUN 8K-SG05LP3-EU-SM2 Battery input data Battery typeLi-lon Battery voltage range (V)40~60 Max. charging current (A)190 Max. discharging current (A)190 Number of battery inputs1 Charging strategy for Li-ion batterySelf-adaptation to BMS PV string input data Max. DC input power (W)16000 Rated PV input voltage (V)550 Starting voltage (V)160 MPP voltage range (V)200-650 Max. DC input voltage (V)800 PV input current (A)20+20 Max. PV short-circuit current (A)30+30 Number of MPPT2 Strings per MPPT1+1 AC output data AC rated power and UPS power (W)8000 Max. AC output power (W)8800 AC output rated current (A)12.2/11.6 Maximum AC output rated current (A)13.4/12.8 Max. continuous AC throughput (A)45 Peak power (without grid)2-fold rated power, 10 S Output power factor0.8 leading to 0.8 lagging Output frequency and voltage50/60Hz; 3L/N/PE 220/380, 230/400Vac Grid typeThree-phase Total harmonic distortion (THD)< 3% ( rated power ) Direct current feed-in<0,5% ln Efficiency Max. efficiency97,60% Euro efficiency97.00% MPPT efficiency99,90% Protection FusesDC Polarity Reverse Connection Protection, AC Output Overcurrent Protection, Thermal Protection, AC OutputOvervoltage Protection, AC Output Short Circuit Protection, DC Component Monitoring, Overvoltage Load Protection,Earth Fault Current Monitoring, Arc Fault Current Interrupter (optional), Grid Monitoring,Islanding Protection Monitoring, Earth Fault Detection, DC Input Switch, DC IsolationImpedance Monitoring, Reverse Current Detection (RCD), Overvoltage Protection Level Overvoltage categoryDC Type II/AC Type III Certifications and standards Grid approvalsIEC 61727, IEC 62116, CEI 0-21, EN 50549, NRS 097, RD 140, UNE 217002, OVE Directive R25, G98, G99, VDE-AR-N 4105 Safety EMC / StandardIEC/EN 61000-6-1/2/3/4, IEC/EN 62109-1, IEC/EN 62109-2 General data Operating temperature range (℃)-45~60°C, >45°C power reduction CoolingIntelligent cooling Noise (dB)<55 dB Communication with BMSRS485; CAN; RS232 Weight (kg)35.2 Size (mm)422B×699.3H×279T Degree of protectionIP65 Installation styleWall mounting Warranty10 years  FAQs about the 8 kW Deye Sun Hybrid InverterWhich battery types does the inverter support?The inverter is compatible with lead-acid and lithium-ion batteries in the voltage range from 40 to 60 volts.What is the maximum charging and discharging current?The maximum charging and discharging current is 190 amps, which enables fast energy transfer.Which protective functions are integrated in the Deye?The inverter offers protective mechanisms such as DC reverse polarity protection, AC output overcurrent protection, thermal protection, AC output overvoltage protection, AC output short-circuit protection, DC component monitoring, optional arc fault protection switch, islanding protection, DC switch, insulation impedance detection, residual current detection, and overvoltage protection class II for DC and AC.Is the inverter suitable for retrofitting existing systems?Yes, the inverter can be easily integrated into existing solar systems thanks to AC coupling.Can the inverter supply unbalanced loads?Yes, the inverter can supply an unbalanced load of up to 100 percent, with each phase supplying up to 50 percent of the rated power. Scope of delivery: Deye SUN-8K-SG05LP3-EU-SM2 (8 kW LV hybrid inverter) 1 x Deye SUN-8K-SG05LP3-EU-SM2 inverterA three-phase hybrid inverter with 8 kW output, integrated LCD colour touchscreen and support for 48V low-voltage battery systems.1 x wall mounting (Wall Mount Bracket)A robust metal mounting rail for secure attachment of the device to a load-bearing wall.1 x Wi-Fi stick (data logger)A plug-in communication module for connecting to the internet for remote monitoring via Deye Cloud or Solarman App.3 x current transformer (CT - Current Transformer)External clip-on current transformers for measuring the energy flows at the house connection, necessary for zero feed-in and self-consumption optimisation.1 x set of PV connectors (MC4 compatible)The required pairs of DC connectors (plus and minus) for connecting the PV strings to the inverter.1 x communication cable (BMS)A pre-assembled RJ45 data cable for the connection between the inverter and the battery management system.1 x mounting kit (screws and dowels)A set of stainless steel screws and heavy-duty dowels for proper installation of the wall mount.1 x user manual (User Manual)A printed manual with detailed installation instructions, wiring diagrams and safety information.

Beltrona High-quality aluminium mounting structure for mounting a photovoltaic module (for all solar module sizes) on flat roofs etc. The installation angle is 30°-60° (ground/roof)

The 10 metre Hoymiles BC05 to Schuko connection cable is the customised solution for the simple commissioning of modern Hoymiles HMS microinverters. While older series used the Betteri connector, the new HMS generation (e.g. HMS-800W-2T) uses the special "Field Connector" (BC05).This cable connects this special connector directly to your household socket. It eliminates the complicated assembly of AC trunk cables for single installations. The high-quality, 10-metre-long rubber hose cable (H07RN-F) is extremely resistant to weather influences and UV radiation, ensuring safe continuous operation of your balcony power plant outdoors.Highlights at a glancePerfect fit: Specially assembled for Hoymiles microinverters of the HMS series (e.g. HMS-600, HMS-800, HMS-1000) with the typical BC05 connector.Simple installation: Connects the inverter directly and without additional adapters to a standard outdoor Schuko socket ("Plug & Play").Long range: With 10 metres of length you can easily bridge distances from the balcony, garden fence or flat roof to the next outdoor socket.High-quality rubber cable: The heavy-duty rubber hose cable of type H07RN-F 3G1.5 mm² is extremely robust, oil-resistant and suitable for long-term outdoor use.High protection class: The BC05 plug on the inverter side is waterproof (IP68), while the Schuko plug is designed for sheltered outdoor areas (IP44).Standard-compliant manufacture: Professionally machine-pressed contacts ensure minimal contact resistance and maximum safety when feeding power.Areas of applicationThis cable is essential for owners of the current Hoymiles generation:Balcony power plants (HMS): For direct connection of an HMS-800-2T to the balcony socket.Garden installation: When the inverter is mounted on the module in the garden and the path to the patio socket needs to be bridged.Retrofit: Replacement of defective or too short original cables in existing HMS systems.Mounting & safety instructionsCheck connection: The BC05 plug must audibly latch onto the inverter to ensure watertightness.Risk of confusion: This cable does not fit the older Hoymiles HM series (these use the Betteri BC01 connector). Please check your inverter connector before purchase.Cable routing: When laying, ensure the cable is not pulled over sharp edges or crushed (e.g. through windows without lead-through).Schuko weather protection: While the BC05 plug is fully weatherproof, the Schuko plug should be inserted into a splash-proof outdoor socket that is ideally covered. Features Model / DesignationHoymiles HMS connection cable (10 m) Connector A (inverter)**Hoymiles BC05** (Field Connector / Female) Connector B (mains side)**Schuko plug** (Type F, IP44/IP65) CompatibilityHoymiles **HMS series** (e.g. HMS-600, 800, 1000, 1600, 2000) Cable specification**H07RN-F 3G1.5 mm²** (heavy-duty rubber cable) Rated voltage**230 V AC** Max. current-carrying capacity**16 A** Protection class (overall)**IP65** (connector) / IP44 (Schuko plug) ApprovalsVDE-tested, CE-compliant  FAQs about the Hoymiles BC05 cableDoes this cable fit my Hoymiles HM-600 or HM-800?No, definitely not. The HM series uses the "Betteri BC01" connector (identifiable by the wave-shaped housing). The HMS series offered here uses the "BC05" connector (smoother, more rectangular design). The connectors are not mechanically compatible.Can I shorten the cable if 10 metres is too long?Technically, this is possible, but you will lose the warranty and the tested safety of the assembled Schuko side. It is often better to safely stow the excess length in a neat loop (not too tightly wound because of induction).Is the cable suitable for 800 watt feed-in?Yes, absolutely. The cable has a cross-section of 1.5 mm² and is designed for currents of up to 16 amps (approx. 3680 watts). The continuous supply of 800 watts (approx. 3.5 amps) presents no thermal problem for this high-quality cable.

The Hoymiles HMS-800W-2T is the powerful successor to the legendary HM series and sets new standards for modern balcony power plants. With a maximum output power of 800 watts this micro inverter gets the most out of your solar modules and is optimally prepared for the current legislation.The "2T" in the name stands for two independent MPPT trackers. This means you can connect two solar modules, which are controlled completely independently of each other. If one module is in the shade or has a different alignment, the second module still runs at full power. Compared to the previous series, the HMS-800W-2T uses the more stable Sub-1G radio technology (for greater range to DTU) and the new BC05 plug-in system.Highlights at a GlanceHigh output power (800 watts): Delivers a full 800 VA of power into the household grid, making it ideal for the maximum permissible feed-in limit of balcony power plants.Two independent MPPT trackers: Guarantees the maximum yield from each individual module, even with partial shading or different alignment (e.g. east/west).Stable Sub-1G communication: Offers a noticeably more stable and wider-reaching connection through walls when used with an (optional) DTU compared to conventional Wi-Fi.New connection system (BC05): Equipped with the proprietary Hoymiles "Field Connector" (BC05) for rapid and extremely watertight installation.Reactive power control: Complies with the VDE-AR-N 4105:2018-11 standard and supports grid stability by providing reactive power.Robust design (IP67): The fully sealed housing is dust- and waterproof and designed for decades of outdoor use in the harshest conditions.Flexible limiting: Using an optional DTU unit, the output can be temporarily restricted to 600 watts via app (S-Miles Cloud) if required.Areas of ApplicationThe HMS-800W-2T is the standard solution for:Balcony power plants (2 modules): The classic – two modules on the balcony railing for maximum self-sufficiency covering your electricity needs.Garages & Carports: Thanks to high protection class IP67 can be safely used on flat roofs.Garden sheds: Easy installation “Plug & Play” (with suitable Schuko cable).Shaded locations: Where a string inverter would fail, the HMS-800 still extracts energy thanks to single MPPT.Mounting & Safety InstructionsCable selection (Important!): The HMS-800W-2T uses the new BC05 connection (rectangular, flat). It is not compatible with the old Betteri BC01 cables from the HM series. When purchasing the connection cable, be sure to look for the note "for HMS series" or "BC05".Distance to the surface: Mount the inverter with at least 2 cm distance to the mounting surface (roof/wall) so that air can circulate behind the unit (passive cooling).Hot Spot: The metal housing acts as a heat sink and in summer at full load can become up to 80°C hot. This is normal, but avoid touching during operation.Earthing: The device is earthed via the AC connection. Additional grounding on the housing is possible, but not usually mandatory if a compliant Schuko/Wieland cable is used (observe local VDE standards). Features ModelHoymiles HMS-800W-2T Max. recommended PV power**320 W to 540 W+** (per module) Maximum output power**800 VA** (adjustable to 600 VA) MPPT number / inputs**2 MPPT** / 2 DC inputs Max. DC input voltage**65 V** Max. input current (DC)**2 x 14 A** (Compatible with modern 500W+ modules) Communication**Integrated Wi-Fi** (2.4 GHz) AC connection**BC05 connector** (HMS series) Efficiency (CEC)**96.7 %** Protection class**IP67** (dust-tight & protection against temporary submersion) Dimensions (W x H x D)261 x 180 x 35.1 mm FAQs about the Hoymiles HMS-800W-2TWhat is the difference with the Hoymiles HM-800?The HMS is the newer generation. The main differences are:Radio: HMS uses Sub-1G (better range) instead of 2.4 GHz (HM).Connection: HMS uses the BC05 connector, HM uses Betteri BC01.Amperage: The HMS tolerates higher input currents (14A), making it more compatible with modern high performance modules (400W+).Do I necessarily need a DTU (Data Transfer Unit)?For pure operation ("generate power"): No. As soon as the sun shines and the grid is present, it generates power. For monitoring (app) and settings (throttling to 600W): Yes. As the HMS-800W-2T does not have integrated Wi-Fi, you need the DTU-Lite-S stick for app connection.Can I limit the inverter to 600 watts?Yes. When used together with a DTU and an installer account in the S-Miles Cloud, the output power can be limited as a percentage (e.g. to 75% = 600W) to comply with current registration requirements.