Mounting material
Mounting kit for 2 solar modules on tiled roofs – with black module clamps
With this complete installation kit, you can securely and permanently mount two solar panels on your tiled roof. The pack contains everything you need for the substructure: six height-adjustable stainless steel roof hooks, four aluminium mounting rails, and end and centre clamps in black. The dark module clamps blend discreetly into the overall appearance of the black solar panels. Ideal for a balcony power plant on the roof or a small PV system on a garden shed, garage or house.The highlights at a glanceComplete set for 2 modules: Roof hooks, rails, clamps, connectors, end caps and screws in one pack.6 stainless steel roof hooks: sturdy, corrosion-resistant and height-adjustable from 120 to 160 mm to suit different tile shapes.2460 mm rail length per row: Two rails, each 1230 mm long, are joined using a rail connector to form a continuous row.Black module clamps: for modules with a frame height of 30 to 40 mm and a width of up to 1134 mm; visually compatible with full-black modules.Designed to withstand wind and snow: wind speeds of up to 35 m/s and snow loads of 3 kN/m².Contents of the package6 adjustable stainless steel roof hooks with L-brackets and connectors4 mounting rails, each 1230 mm long (two of each make a row of 2460 mm)2 rail connectors 40 x 40 mm4 end clamps and 2 centre clamps (black)4 end capsM10 x 25 screws, flange nuts and 18 wood screwsFixing roof hooks correctlyThe roof hooks bear the entire load of the solar panels, including wind and snow loads. For this reason, they are not fixed to the tiles, but are screwed directly onto the rafters using the timber screws supplied. Before installation, measure the rafter spacing and plan the fixing points so that each hook sits centrally on a rafter. Screws that are too close to the edge of the rafter or positioned next to it are one of the most common installation errors.After installation, the tile must not rest on the roof hook, otherwise it may break under load. Thanks to the height adjustment, the hook can be set precisely to the height of the tile. If necessary, lightly sand down the tile at the point of contact using an angle grinder.Important note: Any alterations to the roof covering may affect your roofer’s warranty and your building insurance. It is best to clarify this before installation. Work on the roof should only be carried out with suitable fall protection, protective equipment and at least two people present.Installation in six stepsLifting tiles: Lift or remove the tiles at the planned hook positions across the rafters.Screwing in the roof hooks: Pre-drill holes in the rafter using a 6.7 mm drill bit and screw the roof hooks securely in place using timber screws.Adjust the height and insert the tile: Adjust the hook height so that all hooks are in a straight line and the tile does not rest on them. Tighten the clamping screws to 13–15 Nm and reinsert the tile.Connecting and fitting the rails: Connect two rails at a time using the rail connector to form a row. Position the joint between two hooks, clip the rail into the clamps and tighten to 13–15 Nm.Securing solar modules: Secure the first panel on the outside with the end clamp and on the inside with the centre clamp; secure the second panel in the opposite direction. Tighten all panel clamps to 13–15 Nm.Fitting the end caps: Clip the end caps into the ends of the rails and, finally, check and retighten all screws. Frequently asked questionsWhich solar panels is this mounting kit suitable for?For two framed solar modules, each up to 1150 mm wide.What frame height is the mounting kit suitable for?35 mm. This is standard for most solar panels, but check the data sheet for your panels before purchasing.Can I expand to three or four modules?Yes. For each additional module, you’ll need an extension kit containing 2 roof hooks, 2 rails, 2 rail connectors and 2 centre clamps.Does the fitting kit fit any tiled roof?It is designed for traditional roof tiles and roof pans. For plain tiles, slate or metal roofs, different roof hooks are required.Why are the roof hooks height-adjustable?Tiles vary in shape and height. Thanks to the adjustment range of 120 to 160 mm, the tile does not rest on the hook and is not damaged.Where are the roof hooks fixed?Always on the rafters, never on the tiles. The screws should be positioned in the centre of the rafter.
KSENG Adjustable Solar Universal Mounting Bracket (Black Anodised)
KSENG Adjustable universal solar mounting bracket – black anodisedProduct informationThe KSENG Universal solar mounting bracket in black anodised finish enables the installation of a solar panel in various locations. Whether on a suitable balcony railing, on a wall or on a flat surface: the mounting bracket offers various installation options for your photovoltaic system.The adjustable telescopic supports allow the panel tilt to be adapted to the installation situation. The black finish complements black-framed solar panels in particular, creating a uniform appearance.Highlights at a glance▪ Adjustable tilt: Angle adjustment via telescopic supports.▪ Various mounting options: For balcony, wall and freestanding installation in accordance with the instructions.▪ Black anodised finish: A suitable look for solar panels with black frames.▪ Foldable support arms: Folding support structure for assembly.▪ Inverter mounting provided: The instructions describe how to mount a micro-inverter.Technical specifications FeaturesSpecification ManufacturerKSENG Item numberKSEUESBLACK Product typeAdjustable universal solar mounting bracket Colour / FinishBlack anodised Tilt adjustmentAbout telescopic supports Mounting optionsBalcony, wall, flat surface as per the instructions Weight as stated in the shop5 kg Installation and compatibilityBefore purchasing, check the panel dimensions, frame profile and suitability of the installation site. The term ‘universal’ does not imply unrestricted compatibility with all panels and railings.The mounting and, where necessary, additional securing must be suitable for the surface and the local load conditions. Please follow the installation instructions.Frequently asked questionsIs the panel tilt adjustable?Yes, adjustment is carried out via the telescopic supports.Can the mount be fitted to a wall?Yes, the instructions show wall mounting. The fixings must be suitable for the respective surface.Is a solar panel or inverter included?This item is a mounting bracket. The solar panel and inverter must be selected separately.
Beltrona High-quality aluminium mounting
These Beltrona Universal mounting system is a robust and flexible solution for securely mounting photovoltaic modules on flat surfaces (flat roofs, garage roofs, ground, terraces). Made from corrosion-resistant Aluminium, this design offers maximum durability with a low weight.The special highlight is the Variable tilt angles from 30° to 60°. This allows you to align the solar module perfectly with the sun, thereby significantly increasing the yield of your system – particularly in the case of "balcony power stations" or off-grid systems – The mounting bracket is designed to be universal and fits almost all standard solar module sizes (framed).Highlights at a glanceFlexible bracket (30°-60°): The tilt angle can be adjusted continuously or in steps (depending on the model) between 30 and 60 degrees. A steeper angle (45–60°) is ideal for optimising yield in spring, autumn and winter, when the sun is low in the sky.Universal fit: The structure is attached directly to the frame of the solar module. As the rails are telescopic or can be mounted in various ways, the system is suitable for small 100W modules as well as large 400W+ panels (standard width approx. 1134mm).High-quality material: Made from anodised Aluminium (AL6005-T5) and screws made of Stainless steel (SUS304). This guarantees rust resistance and weather resistance for decades.Versatile installation: Suitable for flat roofs (bitumen, membrane, gravel), concrete surfaces, garden soil or even for vertical wall mounting (facade) to space the module away from the wall.Easy installation: Pre-assembled parts and simple screw connections enable quick installation.Areas of applicationBeltrona ’s mounting system is ideal for:Flat roofs: Garage, carport, bungalow (weighting with ballast stones recommended).Garden / open space: Installation on a lawn or terrace.Balcony power stations: To position modules at the optimum angle on a large terrace or a canopy.Facade: For wall mounting, to tilt the module away from the house wall towards the sun.Installation & Safety InstructionsBallasting (Important!): If you are installing the mounting bracket on a flat roof (e.g. bitumen), you are often not permitted to drill through the roof membrane. In this case, the structure must be weighted down (e.g. with paving slabs or concrete blocks). A single module at a 60° angle presents a large surface area for the wind to catch (sail effect)!Screw connection: The bracket is typically screwed into the mounting holes on the back of the module frame. Check whether your module frame has the appropriate holes or use module clamps.Alignment: Ideally, align the module with South orientation. If a south-facing orientation is not feasible, south-east or south-west orientations also deliver good yields. Features ProductBeltrona Vario aluminium mounting system (30°-60°) Material (profiles)**Aluminium AL6005-T5** (Anodised, silver) Material (connections)**SUS304 stainless steel** (A2/A4 stainless) Tilt angle**30° - 60°** (Adjustable via telescopic leg) Installation locationFlat roof (concrete/bitumen/gravel), open space (ground), wall Module alignmentHorizontal (Landscape) or Vertical (Portrait) - depending on the rail length Max. wind loadup to 60 m/s (depending on ballasting/screw connections) Max. snow loadapprox. 1.4 kN/m² Contents (set)Pre-assembled triangles, slot nuts, Allen screws WarrantyOften 10 years warranty on material durability FAQs on the Beltrona mounting systemIs the system suitable for my 420-watt module?Yes. Current standard modules (approx. 172 x 113 cm) can be installed without any problems. The length of the aluminium arms is designed to safely support these sizes.Why 30° to 60° and not flatter?Flatter angles (e.g. 10–15°) do not self-clean as effectively (rain does not wash away pollen/dust). The 30–60° range offers the best compromise between Self-cleaning and Annual yield. 30–35° is ideal for summer, whilst 60° makes the most of the low winter sun.Can I also screw the system to the wall?Yes, these triangular structures are also ideal for façade mounting. One side is firmly anchored to the wall with dowels, whilst the adjustable side supports the module. Please ensure you use sturdy dowels and screws here due to wind loads.
Balcony Power Station Solar Mount 0–30° adjustable for balconies, railings & walls for PV modules 30/35 mm
Product informationThe adjustable solar mounting bracket for balconies, railings and walls is a flexible mounting solution for framed solar modules and is ideal for balcony power stations and compact PV systems.Thanks to the manually adjustable tilt angle of 0° and 15–30° the solar panel can be optimally aligned with the sun. This allows for better utilisation of sunlight, depending on the location, season and mounting position.The mounting kit is pre-assembled and designed for particularly easy installation. The mounting bracket is unfolded, positioned and secured – making it ideal for quick installation on balconies, railings or walls.The mounting system is manufactured from high-quality, corrosion-resistant materials such as AL6005-T5, AL5052 and SUS304 stainless steel. This makes it robust, durable and suitable for long-term outdoor use. Highlights at a glance Adjustable to 0° and 15–30°Flexible adjustment of the tilt angle for optimum module alignment.Pre-assembled mounting kitQuick and straightforward installation.For balconies, railings & wallsVersatile for use in a variety of installation scenarios.Suitable for framed solar modulesCompatible with modules with a frame height of 30 or 35 mm.Wide range of modulesFor solar modules up to 2,200 mm in length and 751–1,313 mm in width.Corrosion-resistant materialsAluminium alloys AL6005-T5 and AL5052, and SUS304 stainless steel.High stabilityDesigned for wind speeds of up to 40 m/s.Ideal for balcony power stationsIdeal for use with solar panels and micro-inverters.10-year warrantyFor long-term planning certainty. Flexible tilt from 0° to 30° The mounting bracket allows the solar panel to be manually adjusted to various positions. The following are available: 0°Adjustable from 15–30° This allows the solar panel to be positioned optimally depending on the installation location and desired orientation. An adjusted tilt angle can help to make better use of sunlight throughout the day and year, particularly for balcony or wall installations. Quick and easy installation The solar mounting kit is largely pre-assembled and designed for particularly easy installation. The system simply needs to be unfolded, aligned and secured. The modular design enables quick assembly and reduces the installation effort. This makes the mounting system particularly suitable for: Balcony power stationsBalcony parapetsRailingWall mountingCompact PV systemsPrivate solar installations High-quality and corrosion-resistant materials Robust materials are used for the mounting bracket: AL6005-T5 aluminiumAL5052 aluminiumSUS304 stainless steel These materials are characterised by high corrosion resistance and stability. The mounting system is therefore designed for long-term outdoor use. Suitable for many solar modules The balcony mounting bracket is designed for framed solar modules and supports various module sizes. Suitable modules are those with: with a length of up to 2,200 mma width of 751 to 1,313 mma frame thickness of 30 or 35 mm This means the mounting system is compatible with many standard solar panels for balcony power stations and smaller PV systems. Ideal for balcony power stations The mounting bracket is particularly suitable for installing solar panels on balconies and railings. The adjustable tilt allows the module to be aligned more effectively with the sun than with a purely vertical installation. Typical areas of application are: Balcony parapetMetal railingWall surfacesPatiosGarden shedsSmall PV systemsBalcony power stations Technical Specifications FeaturesValue Product nameAdjustable solar mounting bracket for balconies and walls MaterialAL6005-T5, AL5052, SUS304 Suitable modulesFramed solar modules Module orientationLandscape Suitable module thickness30 & 35 mm Max. module length≤ 2,200 mm Suitable module width751–1,313 mm Tilt angleAdjustable to 0° and 15–30° Max. wind speed40 m/s Installation locationsBalcony, railing, wall CertificationISO9001, CE Package size370 × 150 × 80 mm Weightapprox. 2.5 kg Warranty10 years Advantages of the adjustable balcony mounting bracket The mounting system offers several advantages over fixed module installation. Due to the variable tilt angle the module can be better adapted to local conditions. Further advantages: Easy installationCompact designPre-assembled structureShort installation timeFlexible module orientationHigh-quality materialsHigh corrosion resistanceSuitable for various module sizesSuitable for use with numerous balcony power plant systems Installation instructions Before installation, you must check whether the balcony, railing or wall is suitable for the loads involved. In particular, the following must be taken into account: Net weight of the solar moduleWeight of the mounting bracketWind loadslocal weather conditionsCondition of the railing or substrateSecure fastening of all screw and clamp connections Installation must be carried out in accordance with the locally applicable building and safety regulations. If in doubt, the mounting should be checked by a suitably qualified specialist. FAQ on the adjustable solar mounting bracket Which solar panels is the mounting system suitable for? The mounting system is designed for framed solar modules with a frame thickness of 30 or 35 mm suitable. The maximum module length is 2,200 mm, the supported width ranges from 751 and 1,313 mm. Can the angle be adjusted? Yes. The mounting bracket can be fitted to 0° and within the range of 15–30° can be adjusted. This allows the solar panel to be flexibly adapted to the specific installation site. Is the mounting bracket already pre-assembled? Yes. The structure is largely pre-assembled and has been designed for quick installation. The system is unfolded, positioned and then securely fastened. Can the mounting bracket be attached to a balcony? Yes. The mounting system has been designed specifically for balconies and railings developed. However, prior to installation, it must be checked whether the structure in question is sufficiently load-bearing and suitable for the wind loads that may occur. Is wall mounting also possible? Yes. Depending on the local conditions, the system can also be used for wall mounting. The fasteners must be selected to suit the specific wall structure. Is the mounting bracket suitable for outdoor use? Yes. The aluminium alloys and stainless steel components used are corrosion-resistant and designed for long-term outdoor use. Contents of the package 1 × pre-assembled solar mounting kitRequired mounting and connection components as per the set contentsInstallation accessories as specified by the manufacturer The solar panel and micro-inverter are not included in the scope of delivery, unless expressly stated otherwise.