Deye SUN-10K-SG05LP3-EU-SM2 Three-phase low-voltage hybrid inverter 10 kW

The Deye SE-F12 is a state-of-the-art low-voltage energy storage system (48V / 51.2V), designed for maximum reliability and performance in residential and commercial solar installations. With an impressive rated capacity of 11.8 kWh (approx. 230 Ah) in a single, compact housing, this storage system offers an excellent balance of high energy density and proven safety.Thanks to the long-lasting lithium iron phosphate (LiFePO4) cell chemistry and the intelligent battery management system (BMS), the SE-F12 is the ideal choice for users who wish to maximise their self-sufficiency. The system’s enormous scalability also makes it a flexible and future-proof investment in your own energy independence.Highlights at a glanceHigh storage capacity (11.8 kWh): It offers a massive 230 Ah at a nominal voltage of 51.2 V in a single module, which drastically reduces the amount of cabling required compared to smaller 5 kWh blocks.Safe LiFePO4 technology: It uses lithium iron phosphate, the safest and most thermally stable cell chemistry on the market, with no risk of thermal runaway.High-performance power handling: Enables a maximum continuous discharge current of 230 A (approx. 11.5 kW output) and peak currents of up to 280 A for 10 seconds – ideal for high-power loads such as heat pumps or electric vehicle charging points.Extreme scalability: The system scales to meet your requirements. Up to 32 units can be connected in parallel as standard (with a CAN bridge, this can be increased to up to 64 units for a storage capacity of up to 18 MWh).Smart monitoring: Equipped with LED status indicators as well as Bluetooth, RS485 and CAN2.0. Seamless integration with the Deye app enables precise real-time monitoring on your smartphone.Long service life: Certified for over 6,000 cycles (at 80 % depth of discharge / DoD), which corresponds to a service life of 15+ years with daily charging and discharging.Flexible installation: Certified to IP21, the enclosure supports both wall-mounted and floor-standing (stacked) installation to make optimum use of space in the plant room.Areas of applicationThe Deye SE-F12 is extremely versatile and is primarily suitable for:Detached houses: To maximise self-consumption and as a robust emergency power storage solution in combination with hybrid inverters.Commercial systems (C&I): For peak shaving and the storage of large PV yields on agricultural or commercial premises.Off-grid systems: Its high continuous load capacity easily handles self-sufficient off-grid systems with high inrush currents.Installation & Safety InstructionsTransport and handling: Weighing 84 kg the module is extremely heavy. You must ensure that it is carried into the basement or plant room by two people or using suitable lifting equipment (e.g. a stair climber).Temperature management: Although the battery operates within a wide temperature range (-20°C to 55°C during discharge), it should be stored in a frost-free, dry room (15°C to 25°C) to ensure maximum service life and capacity retention. Charging below 0°C is blocked by the integrated BMS for safety reasons.Cable sizing: To transmit the enormous maximum continuous current of 230 A without voltage drops or dangerous heat build-up, high-quality battery cables with a cross-section of at least 70 mm² (preferably 95 mm²) between the storage unit and the busbar or inverter is essential.Compatibility: The system natively supports the Deye protocol and works best via Plug & Play with Deye low-voltage hybrid inverters (e.g. the SUN-10K or 12K-SG04LP3 series). FAQs on the Deye SE-F12Can I use this battery with an inverter from another brand?In principle, yes. The Deye SE-F12 uses standard communication protocols (CAN/RS485) and can often be operated with compatible third-party brands. However, the correct BMS protocol must be manually configured on the battery (via software or DIP switches). Neither the manufacturer nor the retailer provides any support for setting up the system for use with third-party products. A fully functional system can only be guaranteed when using the Deye own-brand product. Please check the compatibility list in advance.What happens in the event of a power cut at home?If you combine the SE-F12 with a hybrid inverter capable of providing emergency power (such as the Deye SG04 series), the system will switch to battery operation within milliseconds in the event of a mains power failure. Thanks to the high discharge power (up to 11.5 kW from a single battery), you can continue to supply even large three-phase loads on the domestic circuit without any problems.Why do some shops list it as "SE-F12-C"?The abbreviation "-C" usually refers to the latest model revision (often the EU version), which is fitted with an integrated LCD display on the front of the casing. This allows cell voltages and SoC to be read directly. The raw performance specifications for the standard SE-F12 are identical.

The AIKO Neostar Pro 3S+ 54 glass-glass Full Black module with 485 W is a highly efficient solar module for demanding domestic and commercial photovoltaic systems. Featuring state-of-the-art N-type ABC cell technology, a robust double-glass construction and an elegant full-black design, this module combines high performance, exceptional durability and long-term yield reliability at a particularly high standard.Performance and technologyAIKO AIKO’s Neostar Pro 3S+ 54 achieves a maximum power output of 485 W with a module efficiency of 24,3 %. The innovative N-type ABC cell technology ensures higher energy yields, optimised performance under partial shading and an improved temperature coefficient. In addition, the double-glass construction supports its use in modern PV systems with high demands on efficiency and design.Robust construction and high reliabilityThe module is constructed as a double-glazed version with 2.0 + 2.0 mm coated, semi-tempered glass and features a black anodised aluminium frame. This design ensures high mechanical stability and a long service life. The module is resistant to micro-cracking, has an IP68 junction box with three bypass diodes and is designed to withstand high mechanical stresses in demanding outdoor applications.Long-term yield securityAIKO offers a 30-year product warranty on the Neostar Pro 3S+ 54, as well as a 30-year linear power warranty. Degradation in the first year is a maximum of 1 %; from the second year onwards, it is a maximum of 0,35 % per year. This means the module is designed to deliver stable solar yields over the long term and offer a high level of investment security.ApplicationsThe AIKO Neostar Pro 3S+ 54 with 485 W is ideal for private rooftop systems, high-quality home projects and commercial installations where high module power, modern design and long-term reliability are required. Thanks to its compact dimensions and high efficiency, it is particularly well-suited to areas where the aim is to achieve as much power as possible per module.Contents of delivery1 x AIKO Neostar Pro 3S+ 54 glass-glass Full Black module AIKO-A485-MCE54Db with 485 W

The SOLR6100 solar cable (100 metres, 6mm²) in red is the professional solution for photovoltaic installations where maximum efficiency and minimum resistance are paramount. With a length of 100 metres per roll and a reinforced cross-section of 6mm², this cable is ideal for large rooftop installations, ground-mounted projects, or systems with high current ratings. The red marking allows standard-compliant identification of the positive pole (+) and ensures clear cabling.Certified according to the international standard IEC 62930, this cable provides the highest safety for modern PV systems with voltages up to 1500V DC. The larger cross-section minimises voltage losses even over long distances and is ideal for high-performance module generations delivering high currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section greatly reduces electrical resistance and ensures higher yield compared to standard cables.Certified safety: Conforms to IEC 62930 (H1Z2Z2-K) standard for use in photovoltaic systems up to 1500V DC.High coverage: 100 metres in one piece allow for individual cuts for custom string connections without unnecessary junctions.Extremely durable: High quality XLPO double insulation is UV-resistant, ozone-resistant and flame-retardant for a service life of over 25 years.Corrosion-protected conductor: Fine stranded, tinned copper provides consistently optimal conductivity and protection against oxidation in humid environments.Wide temperature range: Safe operation under extreme weather conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLR6100 is the first choice for demanding PV projects:Large rooftop systems & PV parksEfficient string cabling and connecting distant module fields to the central inverter.High-performance balcony systemsIdeal for systems with modern modules (500Wp+), to transport high currents without loss.Battery storage & off-grid systemsPerfect for 24V or 48V systems where minimal voltage drops are crucial for charging efficiency.Installation & safety instructionsProfessional connectionUse only MC4 connectors explicitly approved for 6mm² cable with this cross-section and a high-quality crimping tool.Mechanical protectionWhen routing on the roof or through walls, use corrugated conduits or cable ducting to protect the insulation from mechanical abrasion and rodent damage.Parallel cable routingRun positive (red) and negative (black) cables as parallel and close as possible together, to minimise electromagnetic interference (induction loops). Features Model / SKU**SOLR6100** Conductor cross-section**6.0 mm²** Form of supply**100 metre roll** ColourRed (positive pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** Special featureHalogen-free, UV & ozone resistant  FAQs on the red solar cable 100m 6mm²Why should I choose 6mm² instead of 4mm²?For higher yield and future-proofing. Especially with cable lengths over 15–20 metres or when using modules with high current (Isc over 13A), the voltage drop with 6mm² is noticeably lower. This means that more energy reaches the inverter and the cable remains cooler under high load.Can the cable be laid directly in the ground?Only in a protective conduit. Although the insulation is very robust, the cable is not designed for direct burial without protection. In suitable cable protection conduit, however, laying in the ground is no problem.Is the cable resistant to chemicals?Yes. The XLPO insulation is resistant to acids, alkalis, and ammonia. This makes it especially suitable for installations in agriculture (barns) or in areas affected by industrial pollution.

The solar cable SOLS6100 (100 metres, 6mm²) in black is the professional solution for photovoltaic installations where maximum efficiency and minimal resistance are paramount. With a length of 100 metres on a reel and a reinforced cross-section of 6mm², this cable is excellent for large roof systems, open-area projects or systems with high currents. The black identification enables standard-compliant identification of the negative pole (-) and ensures clearly arranged cabling.Certified in accordance with the international standard IEC 62930, this cable offers maximum safety for modern PV systems with voltages of up to 1500V DC. The larger cross-section minimises voltage losses even over long distances and is ideal for high-performance module generations delivering high currents.Highlights at a glanceMaximum efficiency: The 6mm² cross-section significantly reduces the electrical resistance and provides more yield compared to standard cables.Certified safety: Complies with IEC 62930 (H1Z2Z2-K) standard for use in photovoltaic systems up to 1500V DC.Long range: 100 metres in one piece enable custom cuts for tailor-made string connections without unnecessary separation points.Extremely resistant: The high-quality XLPO double insulation is UV-resistant, ozone-resistant and flame-retardant for a lifespan of more than 25 years.Corrosion-protected conductor: Fine-stranded, tinned copper offers permanently optimum conductivity and protects against oxidation in a damp environment.Wide temperature range: Safe operation in extreme weather conditions from -40°C to +90°C (short-term peaks up to +120°C).Areas of applicationThe SOLS6100 is the number one choice for demanding PV projects:Large roof systems & PV parksEfficient string cabling and connection of distant module fields to the central inverter.High-performance balcony power plantsIdeal for systems with modern modules (500Wp+), to ensure the loss-free transport of high currents.Battery storage & stand-alone systemsPerfect for 24V or 48V systems where low voltage drops are crucial for charging efficiency.Assembly & safety instructionsProfessional connectionsFor this cross-section, use only MC4 connectors that are explicitly approved for 6mm² cable, and use high-quality crimping pliers.Mechanical protectionWhen laying on the roof or through walls, use corrugated ducts or cable ducts to protect the insulation from mechanical abrasion and rodent bites.Parallel cable routingRoute the black negative cable as parallel and close as possible to the red positive cable to minimise electromagnetic interference fields (induction loops). Features Model / SKU**SOLS6100** Conductor cross-section**6.0 mm²** Delivery form**100 metre reel** ColourBlack (negative pole) Rated voltageDC: 1.5 kV / Max. 1.8 kV Conductor materialCopper, tinned (Class 5) Temperature range-40°C to +120°C (on the conductor) Standardisation**IEC 62930 / EN 50618** Special featureHalogen-free, UV- & ozone-resistant  FAQs about solar cable black 100m 6mm²Why should I choose 6mm² instead of 4mm²?For more yield and future-proofing.Especially for cable lengths above 15–20 metres or when using modules with high current (Isc above 13A), voltage drop is noticeably lower with 6mm². This means more energy reaches the inverter and the cable stays cooler under high load.Can the cable be laid directly in the ground?Only in protective conduit.Although the insulation is very robust, the cable is not designed for direct burial without protection. Installation in a suitable cable conduit in the ground, however, is no problem.Is the cable resistant to chemicals?Yes.The XLPO insulation is resistant to acids, alkalis and ammonia. This makes it particularly suitable for agricultural (stables) or industrially impacted areas.